T Mobile Pocket PC and Siemens Sx56 Unlocking

[Moosani]

HI too all in this forum i am new one in this

please guide me step by step the procedure to unlock it

Device Information

Rom Version: 3.14.40 ENG
Rom Date: 11/26/02
Radio Version: 6.18
Protocol version: 324e4
Model No: PW10B1
Plateform: Pocket Pc


and when i enter the test mode by pressing 3 button power+action+reset
they show

wallaby
bootloader
v5.15

Gsm ok

please guide me step by step

wbr
Ahsan MOosai




wbr
Ahsan Moosani

[tedd]

Hi to you too,pal! Well don't have to enter the test mode.
First try to install the xda unlock exe file fm this site,and then open it fm your ppc.
If the attept fails,find and download the special rom or rom kitchen,to overwrite a new rom which provides the use of any network.

Finally I've discovered a tip,on sx56.When is asking for SID lock code not PIN,type the number zero eight times.

[cshields1]

HI too all in this forum i am new one in this

please guide me step by step the procedure to unlock it

Device Information

Rom Version: 3.14.40 ENG
Rom Date: 11/26/02
Radio Version: 6.18
Protocol version: 324e4
Model No: PW10B1
Plateform: Pocket Pc


and when i enter the test mode by pressing 3 button power+action+reset
they show

wallaby
bootloader
v5.15

Gsm ok

please guide me step by step

wbr
Ahsan MOosai




wbr
Ahsan Moosani

I just unlocked my TMO XDA 1 ... it was painful! Here's a lesson's learned checklist.
1. Get a SD card reader/writer. ~$20 @ CompUSA.
2. Get a 64M SD Card for Bootloader flashing your unit.
3. Build a 3.17.03.exe ROM image at Yorch kitchen.
4. Backup current CE+boot to your 64M SD card. Enter Bootloader, wait for a "GSM OK" message to appear, press contact button next to speaker. Scroll down to Boot+CE->SD, select. This will copy current ROM to SD card.
5. Take this sd card, put in sd card reader/writer and using OSImageTool.exe (part of XDAtools), copy card to pc folder called CurrentROM or similar.
4. Remove sim & sd card from unit.
5. Put in cradle & connect to pc. Using a guest partnership is okay.
6. Run the 3.17.03.exe file. Mine failed. Couldn't read device config. Said to check USB/serial cable connection.
7. Went back to Yorch kitch, created 3.17.03.nb1 file, downloaded it, copied to SD card via sd card reader/writer & OSImageTool.
8. Insert this sd card into your unit, enter Bootloader & it will ask if you want to load this O/S, do so. This worked for me. Do a hard reset after successfully completion and when it comes up, it states unit is sim locked, do you want to change this, tap Yes. I copied XDAunlock.exe to unit, via A/S to confirm unit was really unlocked. XDAunlock confirmed unit was unlocked.
9. Problem, flashing to 3.17.03 put phone model to PW10A1, mine is PW10B1. Any .exe ROM upgrade software will not work. They "see" a model A and they're configured to install software for a model B ... at least in the USA.
10. To get around this, I put a ROM4.00.21.nb1 on the SD card via sd writer, upgraded unit's ROM via Bootloader. This was successful and model was put to PW10B1.
11. Then I ran my ROM4.01.00.exe which completely finished installing the RSU & ROM on my unit. The advanced copy of TMO's ROM4.01.00, RS6.24.01 is combined into an .exe. I'm sure .nb1 and .nbf exist.

I'm running an unlocked TMO XDA 1 and just packaged it for selling. Good luck.

[Moosani]

i send the xdaunlock file in my ppc and open it but they show error erro to getting code , i send the file with infra red and open it in start>programes>filexplorer>mydocuments

but show error

i have only usb cable and infra red

please guide me

and its hard to purchase com cable from any other site just give me schematic and pinouts for cable i will make it by my own

wbr
Ahsan Moosani

[Peter Poelman]

Your ROM version is too old: if you install the XDA-developers Special Edition ROM it will provide you with some new features, and resolve your SIMlock problem as well.

Note that this will involve cold-booting your device, so backup all your information first.

[Moosani]

how i update to rom because i have only usb cable which comes in box
there is any other way to make cable because it is hard to purchase for me give me schematic and pinouts etc.

wbr
Ahsan Moosani

[Biso007]

you don't need a serial cable to flash your xda. just got to the kitchen at www.yorch.net. cook a ROM based on 3.17 and select the exe method. down load the file to ur PC and connect the xda to the cradle and make sure it's connected to power. run the exe file and follow the instructions.

good luck

[Moosani]

@Biso007

thanks for reply me

but how download the file i find many things but not 3.17

could u give me complete link to download

thanks in adv.

wbr
Ahsan Moosani

[Moosani]

XDA-developers-SER-v12

i download this from another site
this is the right thing to cook my palm on 3.17 check it

please before done any thing i want confirmation

i dont want to loose my palm

:( :( :( :( :( :( :(

[cruisin-thru]

Thats the one, go ahead, make sure you back up your data first.

[Moosani]

i received new phone from america and its locked
i did not make any things in it now they need to make backup
or not

wbr Ahsan Moosani

[cultavix]

3.14 T-Mobile
g32e4
6.18

I want to use my phone in Vodafone in Spain. So I need to unlock.

I have the unlock tool from XDA but it says 'error getting unlock code'

this is due because it is incompatible with the version of ROM/Software I have on my PDA.

Now, I have a small problem. I dont have the USB cables, (I want t buy them but I cant find them ANYWHERE...if any of you know...that would be of MAJOR help.)

Is there a way around that? Is there a tool for my version?

[cultavix]

Can I do this via my SD Card?

http://www.romkitchen.de/

Is this site worth trusting? What would I select to make my phone unlocked? I see on that site a rom for Spain's Telefonica (which I could easily make the switch to, and I wouldnt need to unlock phone?)

Can anyone explain to me the process?

Thanks!