No sound from speaker after upgrading Rom !!

[colderon]

Hallo,

I upgraded my MDA to version 1.12 from Qtek, all works well, but I don't hear the person I call or answer. If I hold the phone (green) button for 2 seconds it switches to the backspeaker and than I can hear the person talk.

Does anybody know how to fix this !!! Help :(

[Aurora13]

Try inserting a headphone plug and remove it, this will prolly fix your issue.

[chinsoponsub]

I already download the mkBigStorage112.nb1 file

[colderon]

Try inserting a headphone plug and remove it, this will prolly fix your issue.

No, I plugged in a headphone and pulled out, but still no sound from the front speaker. Rearspeaker and BT headphone works well.

Anybody?

[colderon]

I noticed that the front speaker works when I have no sd card inserted, when I insert the memorycard again I have no sound from the front speaker.

Well by testing if its a software problem or mechanical it looks like it is mechanical, but is it?

Strange ??? Anybody

[cruisin-thru]

You would need to do a hard reset and see if the problem persists with no additional programs installed. Backup first though.

[colderon]

Yes, I did all I can do, but the problem is still there. I guess that the SD slot makes conntection with the microfoon or the front unit.

[colderon]

Oke, I screwd my MDA open and I looked how I had to put it back to gether again. When I opend it, I swa that this was not a brtand new MDA but I guess it has been repaired a few times, because I found pices of the seal every where. When I opend the back unit from the front unit my frontspeaker just fell out. So I guess that they forgett to screw this tinny PCB on. After I put it all together again, he works fine. The sound is now comming from the front speaker with or without the SD card inside.

Oke, for all of you don't do this at home unless you are prepared to buy a new one. :D

[imapfsr]

colderon,
I also am having the same problem and think it could be a "loose wire" or cruddy slip in the manufacturing. I will attempt the same. Was it just the two screws on the back at the bottom to start, then as it comes apart more of them. Thanks for your help!
Todd

[colderon]

Yes, their are two screws on the back pcb. Then their is a small sqaure connector at one site this one can be taken off, no the large connector with their cellotape. Oke now comes the tricky part, their is an other mall pcb, about 2 cm by 1/2 cm. This one has also an connector, but the small pcb/unit is glued to the SD card holder with dubble sided tape. You have to be very carefull an try first getting something between this small pcb and the sd card holder. If you pull the back pcb from the front pcb the connector will brake off and you have to buy an new small pcb. This small pcb is the unit that connects the front speaker and contains the signal leds (poweled, Bluetooth).

If have no clue what this small unit will cost me, but my is also broken. Somehow it works, but the signal leds don't lite.

Ik hope this will help you

[iggi]

I'm in the states and had the same problem, I ended up taking it apart myself and finding 2 things, 1 the speaker was bad, this is the same speaker as the n-gage or nokia 6610 either is available on e-bay. the other was the actual board that carries the audio has a plug on one end and the plug had a lousy solder job, for this you will have to find a local electronics repair shop, and hope they can solder as well as the guy here, since it all is surface mount technology. over all the soldering cost me $20 and the speaker cost me $10

[JeRoMe_aKa_JaY]

Same problem, no sound this morning.

I remove the SD card, sound came back.
I put the Sd, sound still there.
But when I change the volume, no more sound...

What a #~{#[# bug :(

[shayani]

I tried to open my Jam 2 times and I quit... I'm afreaid to broke something... Where are the old times that everything had a screw and was so easy to unassemble???