Fast USB Charging on O2 XDA Mini

[mbangur]

HI Friends
Do you hv any software to carry out fast USB Charging option, to charge my XDA with same speed as done by AC Adapter...

I have seen that other WM2003 models has this option.... like in HP 6515..

Thanks
Manmohan

[Chatty]

Interesting... I've got a desktop holder which has to modes: charge-only and normal sync/charge mode. I wonder wether charge-only mode "enables" fast charging or wether the AC adapter does something special...

[jedhonx]

If i'm not mistaken, the typical USB port outputs 5V of power at 500mAh (milliamp-hours). And in my case, my shipped charger outputs 5V at 1000mAh . using the supplied charger would charge my Magician twice as fast compared to the USB (explanation below). I think even USB2.0 ports still give out power at 500mAh.

The Magician's battery is rated at 1200mAh. Charging through the PC's USB port would take roughly 2.4 hours. Using the supplied charger, it would take 1.2 hours. Simple equation for charging is, battery rating (mAh) divided by charger rating [so that's 1200mAh/500mAh for USB]. Disregard the voltage for now unless you plan to make your own standard/portable charger. Rule of thumb, refrain charging the battery with a higher mAh rated charger.. It will damage the battery in the long run.

Hope this helps. Cheers!

Although if you could somehow control charging via software that'd be a nifty tool... :D

[ImmortalU]

i doubt it since max current USB can provide is 500mah as any more would damage the port and probably the board.

[Carty]

Hello

Yup, jedhonx your right! Its the amount of power supplied! There is no way that you could use a software to charge the device in USB at faster rates.

The only way it could be thought of is like, if your device processor is running at certain spped, it consumes some power. When it runs at lower speed, it consumes lesser power and so if the software could make your processor run low or to shut down other programs maybe would show you an incresed speed of charging!

Regards
Carty..

[snudel]

what about taking two usb ports with such a hard disk cable?

[c3l5o]

what about taking two usb ports with such a hard disk cable?

One of the following three thing WILL happen if ALL of them...

1-Fried Motherboard
2-Fried Battery
3-Fried Device

The first can happen because the USB ports will send energy to each other, the other two because voltage WILL duplicate... Think like this, when you have a device that uses "normal" batteries like a remote or a portable cd-player that uses two or more 1.5V batteries they use it because the device works with 3V (2*1.5V batteries)... Hope I made myself clear, because my english is quite rusty... ;)

[yoda_143]

The first can happen because the USB ports will send energy to each other, the other two because voltage WILL duplicate... Think like this, when you have a device that uses "normal" batteries like a remote or a portable cd-player that uses two or more 1.5V batteries they use it because the device works with 3V (2*1.5V batteries)... Hope I made myself clear, because my english is quite rusty... ;)

Well if you link USB ports to increase voltage it's true that it'll probably kill the mb. But linking 2 UBS connectors to increase amps is no problem and often done. You end up getting 5V 1A output. You could even link more ports to further increase the maximum supplied amps, alltough I never tested more than 3.
Linking 2 ports in a way that increases amps will NOT fry the mb, will NOT fry the battery and will NOT fry the device.
I'd say give it a try and see if it charges quicker.

[Dandie]

Actually I think it depends on how many separate USB chips are connected to the USB ports. On one chip (or better say channel) can be more than one port be connected on the computer (like with a passive hub). In that case, connecting two USB cables in parallel doesn't change anything. Otherwise you could connect the cables in parallel and simply get more current at the same voltage (not to mix up with setting batteries in serial).

There are USB chips on the market that supply more than the specified 500mAh, but I suppose the Magician itself detects a USB connection to the computer. I remember that the first ROMs could only be loaded by USB chargers when Pin5 was connected to Ground, which was never necessary when a real USB connection was established to the computer. USB connections to the computer only use 4 Pins. This tells me that the Magician distinguishes between a connection to the charger and a connection via PC USB and limits the power drain correspondingly. If that is the case, connecting a cable with two USB ports doesn't help, it's still recognized as PC USB connection by the Magician.

[rockafeller]

it maybe OOT, but still relates. my magician can only be charged by usb cables. wont work on ac adapter. it has been going for few months and it really bugging me since it takes 4 hours to charge through usb cables.

i did try hard reset and no change :(.

[mbangur]

HI Friends

I appreciate that you are trying all your mind to find the solution..
I believe that O2 provied AC Adapter wont pass additional current to screw up the battery life as it is provided by O2 Manufacturer itself. If Adapter takes 2 Hrs to completely charge the O2 Mini, then this can be done by USB cable also.
Also if you see in any other PDA running windows mobile 5 you will see an option of "fast USB Charging"..

It means that it can be done, but we need to find out how it can be done.

Thanks