Overclock over 240MHZ...

[Markino]

Hi guys!
I see that my Jamin is stable at 240MHZ... what is, in your opinion, the hi stable overclock for the Jamin... ?

[median]

Hi, i run my O2 Neo at 240 stable. I'll probably try even 252. It's summer so I wouldn't push it higher than that. 252 could be stable, but depends on conditions. Just try it for few days.

[gianvi]

Running at 240 MHz, it the battery life MUCH reduced than using factory 200 MHz speed?

[median]

My opinion - 'Sligtly' is more accurate then MUCH. But i didn't measure it.

[coolfire74]

252 MHz for 2 month on my XDA Neo with JAMin ROM, without any problem. Battery life is good, did not really see any difference before and after overlocking.

[lsnizzle]

Well, I have been running my wizard at 264 MHz for 4 months straight and it has never failed on me. i have it on all the time after standby and soft resets. ive also tried 276MHz for a while but i had to soft reset it almost twice a day.

[lsnizzle]

BTW, increasing the clock higher than usual does not heat up your device. the most it would do is soft reset it. temperature running at 264mhz is mostly the same as running at factory speed. (well for me it has) dont know about some of you.

[cellchamp]

BTW, increasing the clock higher than usual does not heat up your device. the most it would do is soft reset it. temperature running at 264mhz is mostly the same as running at factory speed. (well for me it has) dont know about some of you.

How do ya measure the temp?

[pititfilou]

How do ya measure the temp?

Xbar can do it ;)

[p12a]

Guys, my device is Dopod 818pro, and i was using OmapClock.exe to OvClock my processor, but, when the first time i run this program, the clock speed, says 264 Mhz? is it supposed to be the correct Processor Speed?
I got confused as i read anywhere else that the default factory speed is only at 180 Mhz.
But why is it my device gives me a 264 Mhz on Clock Speed?

also i've tried all the guides and tricks to keep my Clock Speed at certain number (eg. 216 Mhz). such as using a MemMaid and etc. but still, i always got the number 264 Mhz and it won't change at all... neither after soft-reset nor stand-by.

Anyone got the same problems?

I forgot to mention, when the first time i bought this 818pro, i felt that my device run very fast, even faster than my friends HP 6828 and ATOM PURE. Did i get lucky or sumthin'?
Everything on my device is still on factory setting...
i removed the OmapClock and Other Utility Software..

[cmkumar2k]

also..... there is one more sw.... 'Pocket Hack Master' from http://www.antontomov.com.... have a look whether it has compatiblity with URs.....

might be helpful..... :)

[dnts]

Mine has been stable at 240MHz for 2 months so about 6 weeks ago I bumped it to 252MHz and is stable since.
Nir

[Markino]

thanks! :wink:

[meschle]

Guys, my device is Dopod 818pro, and i was using OmapClock.exe to OvClock my processor, but, when the first time i run this program, the clock speed, says 264 Mhz? is it supposed to be the correct Processor Speed?
I got confused as i read anywhere else that the default factory speed is only at 180 Mhz.
But why is it my device gives me a 264 Mhz on Clock Speed?

also i've tried all the guides and tricks to keep my Clock Speed at certain number (eg. 216 Mhz). such as using a MemMaid and etc. but still, i always got the number 264 Mhz and it won't change at all... neither after soft-reset nor stand-by.

Anyone got the same problems?



I forgot to mention, when the first time i bought this 818pro, i felt that my device run very fast, even faster than my friends HP 6828 and ATOM PURE. Did i get lucky or sumthin'?
Everything on my device is still on factory setting...
i removed the OmapClock and Other Utility Software..

Try installing the demo of sktools - its the only program I know that shows the true processor speed.

[wisnuaji]

i did over clock to my device into 240, and it's works normally, but i don't know how to know that my overclocking was success or not, where can i read the speed of processor after overclocked?
rGrds
-wisnu-

[cellchamp]

how do i keep my device permanently on at a certain speed thgough omapclock?
also i would like the overlock to work at the set speed even after soft resets. Is this possible?

[meschle]

how do i keep my device permanently on at a certain speed thgough omapclock?
also i would like the overlock to work at the set speed even after soft resets. Is this possible?

Yes you can 2 simple methods here

1. Using omapclockplus - see here http://forum.xda-developers.com/viewtopic.php?t=56057

2. Use batterystatus plugin - displays Mhz on today screen and has omap functions inc device wakeup overclocking see here http://forum.xda-developers.com/viewtopic.php?t=55782

You could also use smartskey or notification queue method but above methods use easy install cabs.

[gianvi]

My opinion - 'Sligtly' is more accurate then MUCH. But i didn't measure it.

Just tried - I agree, there is no big difference in battery life - similar autonomy than factory settings when running at 240 MHz...

[hercule18]

Hi,

I really don't recommand to overclock the prophet over 240mhz.
I overclocked my first prophet @252mhz.
I had no crash problem with this overclocking, but it burned the bluetooth chipset. :cry:

Now i have a new one and have a permanent overclock @216mhz, and sometimes i overclock it @240mhz, but usually it' only to do some tests!

The 216mhz is more than enough to do what i want.

Bye

Herc. 8)