Problem when upgrading from TuMa v1.3 to Helmi, no phone?

[tempie23]

Hey All-

Rather then adding to the large Helmi thread, I figured it would be best to start my own...

In short today I upgraded from TuMa v1.3 to Helmi's new ROM: Helmi_BA_WM2k5_AKU_2.3_32mb_v1.rar

Everything went fine during the upgrade, I set the Operator Code to T%CID? which was retrieved by using GetDeviceData.exe and the upgrade went smoothly... but now the phone functionality doesn't work at all. I've tried with two different SIM's, one being a T-Mobile and the other a Cingular. Both just show no service when inserted, although if I place those SIM's into other phones everything works properly without issue and I get 'full bars' (I have another Cingular 8125 and a T-Mobile SDA).

Here is what I have done so far:
- Reupgraded the Radio to the latest rev 1.15
- Recreated the nk.nbf again with retyping the operator code
- Reupgraded to the ROM to Helmi's
- Reunlocked SIM with xdadev_all_unlock-v1.5.exe
... and still no phone service. :(

Any suggestions on how to get the phone functionality to work properly? Its pretty much useless right now... :o

Thanks!
tempie23

[spkr4thdd]

I'm not sure that T%CID is right for an operator code... I know for O2 UK it's O2___001 and I'm sure a T-Mobile code isT-MOB101, both of these are 8 digits... check you're devicedata output again and use the setoperator.bat to set it properly, then try again ;)

It's all good clean fun :D

[gtp]

spkr4thdd
I have the same operator code T%CID? but only on WM5. When i use 2003SE it is DANGA001.

tempie23
I had such error on TuMa 1.4 but reinstalling the ROM helped for a while. Then I tried helmi's ROM and the problem gone. But a couple of days ago it appeared once and reflashing did not help. What I done is downgraded to 2003SE, did a hardreset and reinserted SIM. The phone came back to work. Then installed helmi's ROM again. Now it is working for a day without any trouble, HOPE it's gone forever.

[tempie23]

I tried downgrading and then reupgrading, but it still is stuck. No phone service. Interestingly enough the LED for the phone doesn't even come on anymore.

Interestingly enough when I select the phone settings from the upper menu I'm getting a Popup message stating "The phone is not ready. Wait 15 Seconds and try again." Obviously waiting 15 seconds does nothing...

Any other ideas?

Thanks!
tempie23

[Midget_1990]

sometimes (happened to me) the operator info corrupts when upgrading to WM5

copy the files attached to the update directory and run 'MaUpgradeUt_noID.exe'

[odie3]

I'm not sure that T%CID is right for an operator code... I know for O2 UK it's O2___001 and I'm sure a T-Mobile code isT-MOB101, both of these are 8 digits... check you're devicedata output again and use the setoperator.bat to set it properly, then try again ;)

It's all good clean fun :D

No it is not, it sounds like he has the same SX 66 that I have.

The ID is = AT%CID?

I posted this in this thead Here (http://forum.xda-developers.com/viewtopic.php?t=35630)

[Midget_1990]

read my above post, it can happen to anyone when upgrading to any wm5, mine happened the very first time i upgraded (TuMa 1.3), i dont know how it happens, but it seems to be permanent even with further reflashes (haven't tried 2k3)

[memyselfi007]

read my above post, it can happen to anyone when upgrading to any wm5, mine happened the very first time i upgraded (TuMa 1.3), i dont know how it happens, but it seems to be permanent even with further reflashes (haven't tried 2k3)

HI.

Sorry for my post, but I did not "get" how to fix the "NO Service" error:

This is what I've done today with Helmi_BA_WM2k5_AKU3.5_v1.4.CF2 by baniaczek:

Hi all.

Today finally spent some time, trying to upgrade my Qtek 9090.

Everything went fine:
1st) Did a SD backup of my current settings;
2nd) Updated ROM with SetOperator to my Operator (got from getdevice.txt);
2nd) Updated without problems;

Then used the Qtek by 5 minutes (inclusively i did a phone call), after that could no longer get the "phone" working - exactly when I received a call, the phone "gone out" and never more. After several soft resets and hard resets the phone was always with "no service" message (but strangely, I could go to settings phone, and look for "the broadcasting" networks).

I swaped the SIM to another phone and it was working, never the less I got another working sim, but the problem continues (btw, I always have the PinCode disabled, and I remember now that I forgot to test enabling PinCode request!!!).

Then, just in case I downgraded the phone to W2003SE, again, and everything was working fine.

My radio was 1.12. So upgraded radio to 1.15, and started over again but with no sucess.

When I downgraded once again, the Qtek works fine with either RADIO versions or sims.

Has anyone got this "nice feature"?????

Is there any overcame solution? (My only missing test is to enable Pincode, and test if it works?)

tks for any help

[SilverIce]

I'm having the same issue here as well, tried the comm manger on and off and disable and enable it. Still makes no difference, someone please help me out, I can't get anyone to help me:(