PDA

View Full Version : Bricked my S200 after installing jasper AKU3.3 plz help!

pti_nourson
30th January 2007, 04:19 PM
hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3

i correctly followed the topic , install step 1 (forG3) and step 2

my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)

i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc

no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it

ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0

i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes ;) )

but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)

plz said me there is still a hope!
csjneek
30th January 2007, 05:24 PM
did try upload another rom from bootloader ?
csjneek
30th January 2007, 05:25 PM
did try upload another rom from bootloader ?
but first try a hard-reset
pti_nourson
30th January 2007, 06:24 PM
i don't know how to load a rom from bootloader (i allready have made soft and hard reset
pti_nourson
2nd February 2007, 08:00 AM
no one could help me ?
shayd
2nd February 2007, 10:09 AM
1. dowenload this latest Qtek official rom from here: ftp://xda:xda@ftp.xda-developers.com/Uploads/Prophet/Prophet-roms/Original-Shipped-ROMs/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!
pti_nourson
2nd February 2007, 02:51 PM
i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...

does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?
csjneek
2nd February 2007, 04:48 PM
while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.
pti_nourson
2nd February 2007, 08:19 PM
this rom don't work, it give me the message

error 294 invalid vendor id
pti_nourson
2nd February 2007, 09:37 PM
it's now working ! great !

i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while :p )

thank you verry much
shayd
3rd February 2007, 10:32 AM
it's now working ! great !

i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while :p )

thank you verry much
So you can now change your signature again, right ;)