Custom RUU V5.2

[Olipro]

new custom RUU is complete;

ROM Cookers, the good news is that this is now a single file, simply provide it with an NBH and you have compatibility with all SPL versions.

Fifth edition... with detection of all SPL versions, plus a very special selection of two soft-load options, including an "Unsafe" SPL which can be used to flash your device back to any SPL you desire.

5.2 is a small patch to fix an error with the unsafe SSPL not allowing you to overwrite the bootloader

[mousey_]

Good Work Olipro One Question When Will It Be Available?

Cheers

[jasjamming]

fantastic Oli,

[LinoX]

Great work, guy! (as usual ;))

[the_passenger]

Great works. :)

[Olipro]

ok, Custom RUU is released, enjoy

[Olipro]

uhm... minor bug in the old release... replaced

[cathaomy]

Thanks. You make life a lot easier....;)

[VivaErBetis]

Olipro, I can't flash using your new RUU and Hard 1.11SPL.

I got installed your Hard SPL 1.11. Start the RUU and selected "SPL-1.11 Bootloader" and mark "Is it Hard-SPL?", Everithing goes well but, when it tries to start the upgrade, the machine hibernates and, after some seconds an error 260 appears.

IMHO the RUU can't start the Hard-SPL 1.11.


Any clue?

EDIT: It doesn't leave a RUU.log in C:\ like previous version (?)


Thanks and best regards.

[pof]

@VivaErBetis: put your phone in bootloader mode manually, then start the upgrade.

[brmm0016]

@VivaErBetis

Do you realy have SPL 1.11 on your phone? I think it means "Olipro SPL 1.11" is not SPL 1.11.
"Olipro SPL 1.11" can also be "SPL 1.04" and "Is it Hard-SPL"
So you must choose your original SPL and "Is it Hard-SPL".

[Olipro]

@VivaErBetis

Do you realy have SPL 1.11 on your phone? I think it means "Olipro SPL 1.11" is not SPL 1.11.
"Olipro SPL 1.11" can also be "SPL 1.04" and "Is it Hard-SPL"
So you must choose your original SPL and "Is it Hard-SPL".

no, you're horribly wrong.

1.11.Oli is based on SPL-1.11, 1.10.Oli is based on SPL-1.04

[VivaErBetis]

@VivaErBetis: put your phone in bootloader mode manually, then start the upgrade.
Ok, done and it runs well. Thanks pof.

[brmm0016]

OK, sorry my mistake.

Now i read a lot of more thread, and the most is clear.

Thanks

[Olipro]

ok, Custom RUU 3.5 released, enjoy

[pof]

ok, Custom RUU 3.5 released, enjoy

Thanks mate! This is how I wanted it :)

[jcespi2005]

ok, Custom RUU 3.5 released, enjoy

So quickly, thanks.....

[randomelements]

Great stuff Oli :D

So, let me get this straight: just stick an nbh in the same location as this and run yeah?

Genius and simple!

[petes]

So, do I run this instead of romupgradeut.exe that comes with, for example, the WM6 roms, if I have hard-spl 1.11 installed?

[Olipro]

So, do I run this instead of romupgradeut.exe that comes with, for example, the WM6 roms, if I have hard-spl 1.11 installed?

yes, put it in an empty folder along with the NBH you want to flash, that's all.

[sam2000]

Great works

[joedoe]

Can I use this Custom RUU instead of bundled in the archive RomUpgrade to install Hard-SPL v.2?

[Olipro]

Can I use this Custom RUU instead of bundled in the archive RomUpgrade to install Hard-SPL v.2?

yep, kill my old one if you like (not the NBH mind though)

[joedoe]

yep, kill my old one if you like (not the NBH mind though)

Would it give me any extra benefits?

[Olipro]

Would it give me any extra benefits?

uhm, well if you're comfortable with the one already on it to flash the SPL, no, not really.

[joedoe]

So you mean that the new way is more secure?

[Olipro]

So you mean that the new way is more secure?

you're not going to let this go are you? it's just a new bloody UI...

[Penske MB]

good job!! u da man!!

[joedoe]

you're not going to let this go are you? it's just a new bloody UI...

No, I aren't. Thank you for the great tool.

[Sarumiso]

Does this still work with Hard-SPL 1.13? If so, what should the settings be (1.11 + Hard-SPL)?

Also, is this an updated version of ModifiedRUUUpdater-V2.rar listed in the wiki?

Thanks

[Olipro]

Does this still work with Hard-SPL 1.13? If so, what should the settings be (1.11 + Hard-SPL)?

Also, is this an updated version of ModifiedRUUUpdater-V2.rar listed in the wiki?

Thanks

yeah, select 1.11; doesn't matter whether you tick the Hard-SPL box or not.

[joedoe]

Wow! Did upgrade with this RUU to radio 1.38 in just 6 minutes!

[alharethi]

Oli,
Would this mean that after I do the necessary modification to my system and having Hard-SPL 1.13 Oli on my PDA.... If I want to install another OS for another HERMES with another language, I just do the update using this tool?...
which basically means this won't overwrite our new "YOU" SPL 1.13, right?

Thanks

[Olipro]

Oli,
Would this mean that after I do the necessary modification to my system and having Hard-SPL 1.13 Oli on my PDA.... If I want to install another OS for another HERMES with another language, I just do the update using this tool?...
which basically means this won't overwrite our new "YOU" SPL 1.13, right?

Thanks

so long as you select 1.11 when you flash it, then no, 1.13 will be untouched.

[Olipro]

Custom RUU 3.6 released; this does nothing except make it a bit more noob friendly.

[TechBill]

Custom RUU 3.6 released; this does nothing except make it a bit more noob friendly.

I suggest to print it as

SPL-1.11 or higher New Bootloader so you wouldn't have to release a new RUU every time you release a new version SPL =P


It was a good idea renaming it to ROMWrapper.exe so folks know it can be used to upgrade or downgrade ROMS!


Bill

[LinoX]

Hi Olipro. First of all thank you for your precious work.
Just a stupid question..
Why do you ask the user what SPL is currently installed on the phone?
Couldn't you read it directly from the phone? (it should be connected if you're attempting to flash it) :)

Does a command to read BL version exist?
If so.. why don't you use it? :)

[Olipro]

Hi Olipro. First of all thank you for your pecious work.
Just a stupid question..
Why do you ask the user what SPL is currently installed on the phone?
Couldn't you read it directly from the phone? (it should be connected if you're attempting to flash it) :)

Does a command to read BL version exist?
If so.. why don't you use it? :)

because it'd require putting the phone into bootloader mode straight away, and since the App is a quick C# job, spending the time to make it interface with USB would be painful and I really can't be arsed. :P

[LinoX]

because it'd require putting the phone into bootloader mode straight away Don't you already do that to flash it? :confused: I'm getting a bit confused..

[Olipro]

Don't you already do that to flash it? :confused: I'm getting a bit confused..

yes... but the two flashers are two different RUU's that I "wrapped"... look, it's time-consuming and I can't be arsed to do it. end of story.

if anyone else wants to devote the time doing it... feel free, I'll help you whereever possible.

[LinoX]

if anyone else wants to devote the time doing it... feel free, I'll help you whereever possible.I'll begin writing an "un-netz"..;)(but if I could have the sources I'll avoid a lot of work :p) I'll let you know.. :) thank you again.

[Olipro]

I'll begin writing an "un-netz"..;)(but if I could have the sources I'll avoid a lot of work :p) I'll let you know.. :) thank you again.

no matter... found a tool that can interface it for me when fed the right address (thanks for that pof) so I've coded a new one... autodetection, enjoy.

yeah, I use netz mainly to decrease the size rather than protect the code

[randomelements]

Man, you keep cranking them out. Thanks for v4 Oli :)

[pvs]

Custom RUU 3.6 released; this does nothing except make it a bit more noob friendly.

I thought you (and others) might get a chuckle from this.

http://www.thinkgeek.com/images/products/front/B-MAKEI_solo.gif

Thank you so much for the wonderful work that you, pof, des, sleuth, daniel herrero, shogun, kyphur, lvsw, jasjamming, and all the rest of the gurus do for the xda community. Since I found this place a few months ago, not a day goes by when I am not awe-struck by your collective talents.

I haven't yet made use of any of the concoctions that have been developed, mainly because I'm awaiting an Outlook 2003 CD so I can continue to sync my work pc. But it should arrive any day now, so I should be able to taste some of these yummy goodies you guys have whipped up. Needless to say, I can't wait!

Thanks again,
-pvs

[Penske MB]

thx for the great job!!

[LinoX]

yeah, I use netz mainly to decrease the size rather than protect the code
I supposed that :) ..and if you would ever need to obfuscate your code I've bought a professional license for Dotfuscator 4 ;) feel free to simply ask :)

[Olipro]

I supposed that :) ..and if you would ever need to obfuscate your code I've bought a professional license for Dotfuscator 4 ;) feel free to simply ask :)

hehe, nah, I'm not in the business of trying to make people's lives hard if they want the source code to my stuff.

thanks for the offer though

[simon1219]

If I will to extract Windows.nb from RUU_Hermes_QTEK_WWE_2.11.255.1_102_6275_1.38.00.10 _108_Ship.exe extract using nbhtool.exe, convert Windows.nb to RUU_signed.nbh and then flash using RUU 4.0 will erase the old extRom and radio currently in my phone?

[vp3G]

If I will to extract Windows.nb from RUU_Hermes_QTEK_WWE_2.11.255.1_102_6275_1.38.00.10 _108_Ship.exe extract using nbhtool.exe, convert Windows.nb to RUU_signed.nbh and then flash using RUU 4.0 will erase the old extRom and radio currently in my phone?No, Windows.nb is the OS file. The radio and ExtROM are separate .nb files that will also be extracted by nbhtool, usually named something like "gsm" and "extrom", but they can vary from ROM to ROM.

[simon1219]

No, Windows.nb is the OS file. The radio and ExtROM are separate .nb files that will also be extracted by nbhtool, usually named something like "gsm" and "extrom", but they can vary from ROM to ROM.

That means I can safely flash the OS ONLY and retain my old DopodAsia extROM (currently my phone has radio 1.38.00.10)?

[Olipro]

new CustomRUU; compatibility for 1.35 added, that's all

[okk]

Thanks,This is how I wanted it

[joedoe]

The new Custom RUU V4.2 doesn't detect SLP-1.40oli which I just installed on my device, says to use SSPL.

Edit: Resolved.

[attot1239]

It's a real great tool, thanks to all participated.

Regards

[TBCompDesign]

Seems the download target for the posted file is bad. Can it be reuploaded or posted elsewhere?

[Olipro]

Seems the download target for the posted file is bad. Can it be reuploaded or posted elsewhere?

no, use a download manager like FlashGet

[TBCompDesign]

no, use a download manager like FlashGet

Flashgot didn't even work... I'm not sure if there was a problem with the servers or what, I was getting 27-39k files in firefox, IE and using Flashgot. Finally I tried for the 30th time and it seemed to download the entire file and was extractable.

Thanks for the quick reply though.

[Zgembo]

@Olipro:

I was trying to flash ExtROM tonight. Was using previous versions of RUU without problems... When I get manually into bootloader (your 1.40), and try to flash something, RUU 4.2 gives me error:

ERROR [200]: INVALID UPDATE TOOL

Please get newer Update Utility

wtf? is this 'a feature' or some weird shiit?

EDIT: Ooops, ActiveSync gone wild! Reinstalled it and it's fine now... Sorry m(_ _)m

[Olipro]

@Olipro:

I was trying to flash ExtROM tonight. Was using previous versions of RUU without problems... When I get manually into bootloader (your 1.40), and try to flash something, RUU 4.2 gives me error:

ERROR [200]: INVALID UPDATE TOOL

Please get newer Update Utility

wtf? is this 'a feature' or some weird shiit?

EDIT: Ooops, ActiveSync gone wild! Reinstalled it and it's fine now... Sorry m(_ _)m

interesting behaviour though... the HTC RUU for the new Hermes SPL is technically identical to the Trinity one by the way.

[Olipro]

new customruu uploaded for the new SPL

[zend]

new customruu uploaded for the new SPL

I just made a donation. Thanks for your work on this!

[Olipro]

I just made a donation. Thanks for your work on this!

thanks a lot, much appreciated!

[sambartle]

Gotta be worth a donation.. its on the way :)

Cheers,
Sam

[Surobrain]

AutoDetect errored out (unknown version) when I used V4.3 on a recent ROM upgrade. I clicked the radio button to my SPL version (2.10) and everything flashed fine.

I was not in bootloader mode, but in previous versions/combos (e.g. 4.2/1.40) I didn't need to be, just needed Active Stink to be done with it's sync.

Any thoughts?

EDIT:

I flashed back to another radio ROM and had no AutoDetect issues with that NBH file, must be the the NBH file (Custel 1.3 Cingy) of the other ROM?

[K-Mile]

--Resolution below--

First of all let me apologize if this has been posted on the forums before, I have searched extensively and couldn't find any other occurrences of this problem.

Since a couple of weeks (haven't been flashing my phone in a while..) whenever I start RUUWrapper it immediately crashes and shows a Windows 'Send Details to Microsoft' screen, on Windows XP sp2.

It doesn't matter if I use any version of RUUWrapper or the older version (ROMUpgradeUt.exe), it always displays the same error.

I will try to perform the update on another workstation now, with a fresh ActiveSync install etc, but I am very curious what might cause the problems.

The first time they occurred was when I was trying out some different upgrades, and suddenly it just failed to start (been doing 5-6 updates the same day successfully)...

If there's any other info that's useful please let me know so I can provide it, thanks.

[mrvanx]

Have you double checked your machine has the latest .net framework installed?

[K-Mile]

Yeah, sorry, forgot to mention that.

got .NET 1.1, 2.0, and 3.0 installed on my workstation.

[K-Mile]

I found the solution to the problem posted above.

Apparently, RUUWrapper does not function properly when run from a network drive. At my workstation, we use 'My Documents' redirection, that stores a local copy of the 'My Documents' folder on the network. This ensures that you can continue to access documents when the network fails, but to Windows, the folder is a network share.

Obviously, you'll never want to flash your phone from a network drive, so I copied all the files to the local file system. Not a single problem there.

[zoeshcn]

hey guys,

I bought my Hermes yesterday. it's X01HT, in WM5 traditional Chinese already. I am trying to get it into WM6 black 2.5. I went to "the hermes guide" and did EXACTLY as it said, and sucessfully flashed the HardSPL. When I try to upgrading the radio, there was th problem, when I click "auto detect" it shows "In order to use this feature, your PDA must be running Windows Mobile, you may need to confirm this check on your PDA also. it must be synced with ActiveSync: have you done this". After i click yes, there is the confirmation thing on my X01HT, i click "yes" there also. But then i got "Erro, unknown version! You should pick SSPL" on laptop screen.

I tried to skip upgrading the radio, and do the rom directly, got the exact same problem.

I have been here for a week, but never saw other people with this problem. (i'll look again, just in case some one posted the same question) Anyone could help me out here??? I'll be waiting online for answers.

Thanks.

Zoe

EDIT:

ok!! GOT IT DONE.....(kinda feel myself stupid.)

thanks anyway

[K-Mile]

hey guys,

I bought my Hermes yesterday. it's X01HT, in WM5 traditional Chinese already. I am trying to get it into WM6 black 2.5. I went to "the hermes guide" and did EXACTLY as it said, and sucessfully flashed the HardSPL. When I try to upgrading the radio, there was th problem, when I click "auto detect" it shows "In order to use this feature, your PDA must be running Windows Mobile, you may need to confirm this check on your PDA also. it must be synced with ActiveSync: have you done this". After i click yes, there is the confirmation thing on my X01HT, i click "yes" there also. But then i got "Erro, unknown version! You should pick SSPL" on laptop screen.

I tried to skip upgrading the radio, and do the rom directly, got the exact same problem.

I have been here for a week, but never saw other people with this problem. (i'll look again, just in case some one posted the same question) Anyone could help me out here??? I'll be waiting online for answers.

Thanks.

Zoe
I had the same problem following these steps. Flashing radio using SSPL is not a problem though, worked like a charm for me. The ROM then detected the SPL (oli's 2.10) perfectly.

[Olipro]

Oi, MORONS, CUSTOMRUU DOESN'T MAGICALLY UPDATE ITSELF TO RECOGNISE THE NEW SPL... YOU HAVE TO DOWNLOAD THE NEW CUSTOMRUU FOR THAT; OR SELECT THE OPTION FOR 1.11 MANUALLY

now hopefully you bastards will pay attention

[vp3G]

Oi, MORONS, CUSTOMRUU DOESN'T MAGICALLY UPDATE ITSELF TO RECOGNISE THE NEW SPLIMO nothing at XDA-devs should be distributed with RUU... nbh's only... otherwise it's too damn easy for the morons to skip the reading and go straight to downloading and flashing their shit willy-nilly. The chefs should make them seek out RUU and maybe learn something in the process.

[Olipro]

IMO nothing at XDA-devs should be distributed with RUU... nbh's only... otherwise it's too damn easy for the morons to skip the reading and go straight to downloading and flashing their shit willy-nilly. The chefs should make them seek out RUU and maybe learn something in the process.

no, then they spam us with "this file I want put on PDA... how can I do?"

[mrvanx]

LOL, i hear ya oli......hence why ive repackaged the radios in the wiki with 4.3..........damn you when you release a newer SPL ;)

(worth the hassle when i reduces the stupid posts ;))

[vp3G]

no, then they spam us with "this file I want put on PDA... how can I do?"That's when the Ignore List comes in handy. :p

[SeeSharp]

I'm using the newest version of RUUWrapper.exe from this topic. When I choose AutoDetect, I confirm the "ActiveSync required" dialog box and then allow the program to execute on my Vario II. Then RUUWrapper has selected SPL-1.04/1.10 as my bootloader. However I just installed HardSPL-v7. Doesn't that mean I have bootloader 2.10? What should I select in RUUWrapper?

[todd_jg]

Hmmm.... odd.
Put your phone in bootloader mode and confirm what is on there.

[SeeSharp]

The bootloader showed it had been upgraded to 2.10-olipro, so its odd RUUWrapper disagreed.
In the end I just selected 2.10 on the RUUWrapper with Hard-SPL checked, and everything went ok. Prob a small bug?

[samy.3660]

sorry deleted

[samy.3660]

The bootloader showed it had been upgraded to 2.10-olipro, so its odd RUUWrapper disagreed.
In the end I just selected 2.10 on the RUUWrapper with Hard-SPL checked, and everything went ok. Prob a small bug?
I second that. May be some bug, or maybe we are missing something, plz check olipro.

Thanks

[kofijay]

:confused: I have a major problem here...
I use a O2 MDA just the same as T-Mobile MDA Vario... I have looked everywhere for information on my O2 MDA 'Vario' but have had little or no results. I would want to know if there are any RUU for O2 MDA 'Vario'?
Help Please!!!!!!!!!!!!! :-(

[Midget_1990]

:confused: I have a major problem here...
I use a O2 MDA just the same as T-Mobile MDA Vario... I have looked everywhere for information on my O2 MDA 'Vario' but have had little or no results. I would want to know if there are any RUU for O2 MDA 'Vario'?
Help Please!!!!!!!!!!!!! :-(

http://forum.xda-developers.com/announcement.php?f=306

[calculus]

This is probably a stupid question.
But can anyone tell me how to install the RUUWrapper on to
my 8525?

thanks.

[Lurch3559]

This is probably a stupid question.
But can anyone tell me how to install the RUUWrapper on to
my 8525?

thanks.

YOU NEED TO READ, READ , READ. RUU is for flashing ROM's to your device, it is not a program to install on your device. If I were you I would take some friendly advice, read before you do something dum which will cost you your phone.
Asking a question like this indicates that you haven't read this thread nor any other.

[calculus]

Thanks for the advise.
I know RUU is for flashing rom.
But this RUUwrapper cannot run by itself. I sure don't know how
to combine it with my other ROM that I would like to flash.
I read the whole thread and everyone just kept saying
"I successfully upgraded my Hard-SPL". How can you upgrade your
hard-spl when it doesn't run?

Nevermind... after I install the .net 2.0, the program is running now...
thanks for the feedback. :)

[Xdenwarrior]

Yo, without reading anything in this thread, i just wonder if using your new flashing method of RUU i can install WM6 Wizard ROM unto my Dell Axim running WM5. So, can I?
I just got a person at Aximsite who tried to upgarde to WM6 on his Dell Axim using RUU, but got an error.

[calculus]

You will probably need to get the upgrade from Dell.
you can't upgrade dell using Wizard rom.

[Xdenwarrior]

Thanks for the info. Now i started reading through this thread just to find out what this customRUU really does, but i still don't really get it. People say that you need a Hard-spl,.. what is that?
From what i understand is RUU really just an alternate way of flashing your device with the ROM that is designed for it?
(so this replaces just the default flashing that comes with Rom which is, for example, made by Dell).

Otherwise, if i use it to flash Wizard or Hermes Rom on my Dell Axim, i will just brick my device. Right?

[pbalsam]

hi!

Now i've got SPL-2.10 Olipro. I would like to go back to SPL 1.11 which was my ordiginal SPL with original HTC rom from march 2007 ROM number 2.11.255.1

Please help me because i've got to give my Hermes to warranty service. My camera is not working:(

[Xero]

I just bought an X01HT (JN Hermes), and was about to install Hard-SPL.
I quickly discovered that I needed .NET CF 2, which I installed.
I now get an error message that seems to say the program has crashed (though I can't really read it, as it's in kanji).
Anyone else experience this problem?

Update: Accidentally fixed.

[gerald_s]

you don't need .net CF, you need .net framework for your desktop windows.

[biswajitghosh]

my bootloader is 2.03 and imate jasjam is struck in bootloader screen.how do i use ruuwrapper.plz help me ?

[wildfirebr]

my bootloader is 2.03 and imate jasjam is struck in bootloader screen.how do i use ruuwrapper.plz help me ?
Hi I'm having problems with spl 2.03 too, Olipro please make a version of customRUU compatible with spl 2.03 and perhaps I'll see a light in the end of role.
Thanks:rolleyes:

[marcoryn]

A lot of people brick there phone on 2.03. Mine too. Hope Olipro can fix this soon. Can't do anything with my phone right now. Make a donation soon for the good work oli!!!

[yhc1126]

thank you very much!!!:)

[Olipro]

Hi I'm having problems with spl 2.03 too, Olipro please make a version of customRUU compatible with spl 2.03 and perhaps I'll see a light in the end of role.
Thanks:rolleyes:

RUUWrapper was never intended for people who are deliberately using stock SPLs.

I suggest you either flash Hard-SPL or manually select to use SSPL, I have no intention of supporting people intent on actually doing something this stupid.

[mephisto2207]

Hi, a customer gave me an herm200, in IT, as I'm not understanding so well IT language, I've managed (tried) to switch it in UK or FR, succeed with SATIN normal it's nice and in UK with WM6, but during all the process I did, I broke the radio, I've tried with HERM_Radio_Only_1.41.00.10_CustomRUU to fix it, but unable until here, I've make before a brik with my mobile and was saved by mtty and SPL-1.01MFG_Pack, I do not have micro Sim to do the manip with the card, if anyone can help me pls :eek:

[chung_cha]

i has bug the same somebros , when used .net framework 2 i run Ruu then had bug, So i installe .net framework3 .woah great now i can flash with Ruu to upgrade rom , radio v..v
So i say somebros have bug same me when used ruu ex:crash ..So need to try install other .net framework version .U can fix bug
regard
Note : sorry english 's poor:D

[Olipro]

new RUUWrapper is RELEASED.

[michaelhxp]

这个工具太棒了。

i love this great tool. cheers.

[okk]

Thanks Olipro
What time you are going to release Hardspl 2.30?

[Hyins]

Great works :D :D

[randomelements]

Appreciated as always Olipro :)

[Olipro]

5.1 is released. this is a small bugfix for the SSPLs

[Hyins]

:eek: Thanks!

[Olipro]

*pokes*

do please remember to use this for future flashes.

[Hyins]

:eek: Th..thanks

[jjjjayd13]

new custom RUU is complete;

ROM Cookers, the good news is that this is now a single file, simply provide it with an NBH and you have compatibility with all SPL versions.

Fifth edition... with detection of all SPL versions, plus a very special selection of two soft-load options, including an "Unsafe" SPL which can be used to flash your device back to any SPL you desire.

Am I correct, that to bring my phone to original from what it is now, just download current ATT rom? Will this also bring back radio to 1.40?

TIA:confused:

[Olipro]

Am I correct, that to bring my phone to original from what it is now, just download current ATT rom? Will this also bring back radio to 1.40?

TIA:confused:

well it will if you actually use the unsafe SSPL to flash it.

[Olipro]

and bump... really need to raise awareness of this

[parly]

how can I start the flash rom manually directly to the bootloader on my device?

Htc Tytn
IPL 1.04
SPL 2.03

Thanks

[mandrillo]

Dear Sirs,

First of all, I appreciate Your great professional work :) and this very interesting forum. I am new and I read the forum user guide.

I want to flash an Schaps WM6 ROM but I am more difficult :( .
I start with an Vodafone branded HERM200 with spl 1.09 and ipl 1.01
ROM 2.04.161.2, RADIO 1.32.00.00 PROTOCOL 32.65.7020.09W.

I install net framework and Hard-spl V7 and now : ipl 1.04 and spl 2.10 Olipro.

When I start the Schap's WM6 Pro 3.54 (tanks Schap for Your Great Work),
I select according more readings the "AUTO DETECT" spl, but I receive
this error : ERROR Unknown version. You should pick SSPL.

If I select SPL 2.30 Bootloader with is-it Hard SPL have this message :
"Please be aware that this flasher is intended solely for SPL 1.11
and you MUST have 1.11 installed in order to flash any unsigned files"

I not proceed ... because I have SPL 2.10 Olipro... prior to damage.. :confused:

I use Your next version of RUUWrapper.exe without results

Can someone help me ?
I very appreciate Your reply
Excuse me for cross-point but I think this is the good place for my Q.

Francesco.

[todd_jg]

Dear Sirs,

First of all, I appreciate Your great professional work :) and this very interesting forum. I am new and I read the forum user guide.

I want to flash an Schaps WM6 ROM but I am more difficult :( .
I start with an Vodafone branded HERM200 with spl 1.09 and ipl 1.01
ROM 2.04.161.2, RADIO 1.32.00.00 PROTOCOL 32.65.7020.09W.

I install net framework and Hard-spl V7 and now : ipl 1.04 and spl 2.10 Olipro.

When I start the Schap's WM6 Pro 3.54 (tanks Schap for Your Great Work),
I select according more readings the "AUTO DETECT" spl, but I receive
this error : ERROR Unknown version. You should pick SSPL.

If I select SPL 2.30 Bootloader with is-it Hard SPL have this message :
"Please be aware that this flasher is intended solely for SPL 1.11
and you MUST have 1.11 installed in order to flash any unsigned files"

I not proceed ... because I have SPL 2.10 Olipro... prior to damage.. :confused:

I use Your next version of RUUWrapper.exe without results

Can someone help me ?
I very appreciate Your reply
Excuse me for cross-point but I think this is the good place for my Q.

Francesco.

You can proceed. Ignore the warning. It is an old warning.

[Olioaglio]

You can proceed. Ignore the warning. It is an old warning.

I second this, you can override the warning!! You will be safe with flashing.

Olioaglio

[kernelguy]

I had played around quite a bit with my old Wizard. When I got my Hermes, there was still a lot of reading and learning, particularly on SPL version. This RUU made things much simpler.

kernelguy

[VivaErBetis]

Hi Olipro,

I've tested the 2.60.Olipro SPL with this RUU wrapper.

I enter manually into bootloader mode and then I choose 2.30 New Bootloader and Hard SPL. Tried to flash a Radio ROM. Everything OK but, when 100% was reached there appears an UPDATE ERROR and an autorecover utility starts. But the radio was flashed completely right...

Maybe I'm doing something wrong or the RUU needs an update for 2.60?


Thanks and best regards ;)

[cp1md2b]

I'm having a strange problem. I'm unable to flash my Cingy 8525. ipl-1.04 SPL-2.03. I get the following message "Custom RUU has encountered a problem and needs to close. We are sorry for the inconvenience." It doesn't matter what I'm trying to flash. The only things I am able to flash are official cingular Roms. Can someone please direct me on what to do. I have tried to reflashing to an official and then to a custom rom but no luck. I was using vp3G v3.62 before I noticed this.

thank you for any help.

P.S. also tried putting in bootloader. No luck.:confused:

[eljamy]

Hello,

My english is very bad.....

I have a HTC P3300 with spl 1.36, I was probe to upgrade to 1.40 with RUUWrapper 5.2 but if I pick to autodect it says ""unknown vesion should pick safe sspl"", but if I pick to Force safe it says ""Error 240: file open""

I was probe to unlock with the hermes sim unlock v3a, but it says corrup image"

What does I do?

thanks

[mrnikt]

Thanx for great tool :)
I have only one question. There is option "Force safe SSPL". Does it mean that SSPL will be automaticaly transferred to PDA .. or I have to run SSPL - as it is said in SSPL Readme file and then run CustomRUU and check above option and start flashing ?

[rbiten]

Hello,

My english is very bad.....

I have a HTC P3300 with spl 1.36, I was probe to upgrade to 1.40 with RUUWrapper 5.2 but if I pick to autodect it says ""unknown vesion should pick safe sspl"", but if I pick to Force safe it says ""Error 240: file open""

I was probe to unlock with the hermes sim unlock v3a, but it says corrup image"

What does I do?

thanks

Hi,
I'm having the same problem. Did you manage to get it solved?

Thanks in advance.
Rafael

[Olipro]

Thanx for great tool :)
I have only one question. There is option "Force safe SSPL". Does it mean that SSPL will be automaticaly transferred to PDA .. or I have to run SSPL - as it is said in SSPL Readme file and then run CustomRUU and check above option and start flashing ?

no, it's deployed automatically... and it's not the SSPL you're thinking of, this is an entirely different kettle of fish (the mechanism of action is the same, but it doesn't use Des's program)

[drgdrg]

Hey - sorry to post with a lame question on this, but I've really screwed things up a bit. Tried following the directions, but seems like something is off.

On the 8525 I've upgraded to:
Herm100 / IPL-1.04
Herm100 / SPL-2.10.Olipro

I'm now trying to upgrade to v6 and not having any luck. Whenever I run one of the files for the cingular models:


It starts the RUU wizard which kills the ActiveSync process, and my 8525 screen goes into the red-green-blue-white stripe mode. Only way I've found out of it is to reset.

Cingular tech support was no help. Spoke to someone who had no idea what I was talking about, put me on old, and said it must be defective. Thanks.

I've tried downgrading to start over, but I can't get RUUWrapper to launch. Whenever it does, I just get:

Process ID = 0x5c0 (1472), Thread ID = 0xfa0 (4000)

I've tried on two machines (XP and XP/64) and the other (the 32 bit) also similarly bombs out, with no descriptive error message.

Anu suggestions?

Thanks!

Chris

[drgdrg]

Sorry ... two stupid things:

1. I left this out of the post - trying to upgrade to:

RUU_Hermes_CINGULAR_WWE_3.62.502.3_6275_1.54.07.00 _108_UOOS_SVN05_Ship.exe


2 - Did a hard reset and it finally went through. Ignored that the screen went stripes ... ignored that it said make sure active sync was running ... and then it seems to be running, up to 12%. I'm sure I'll ask again when I break another piece of it.

Thanks

[igord]

Process ID = 0x5c0 (1472), Thread ID = 0xfa0 (4000)


Try to download rar/zip again, it sometimes happen to me size of the RUU changes from 1.07MB to 1.09MB.

[potatophone]

Drgdrg: I am suffering exactly the same problem you described - running the update kicks it into bootloader mode, and kills activesync.

[Maikeu Locatelli]

I CAN USE the force unsafe SSPL of this program in elf, or is only hermes?

[acolon2007]

How do i put my phone on bootloader? im new to all this.

[drkawal]

i bought a o2xda trion and when i use ruu everytime it showing same error 240 and after that there is one page come over there its error 240 please check the update utility either you know how to change the language of pda or english romi will be verythanlful to you coz right now my pda is having deutch language and i dont no that please help me out.

[mihaigsm2003]

HI!! I have herm200, and my pda is stuck in "windows mobile". I try reflash with RUUWrapper but is restarts in 100% and get some error. PLS help.

[sahuja]

1. Flashed HardSPLV7 on to my Hermes
2. Downloaded the latest CustomRUU 1.07 MB (1,122,304 bytes), still the Autodetect option is not able to detect the SPL version.
I get the error message as Error Unknown Version. You should pick Safe SSPL. Activesync is connected.

a) What could be the issue?
b) I wanted to flash WM6 using Schaps_WM6Pro_Hermes_4.31_WWE_Full on to my WM5 Vario II and since this Autodetect is not working whats the option i should select among the different boot loaders?

Should i select the Is it HardSPL checkbox ?

[punhop]

hey freinds please help me i tried to download some software from xda develepors and my device X01ht is gone all blank..when it starts nothing can be seen ..its blank..what should i do...please i am waiting for all your help...

[alexandrito99]

Hi guys, I have a Vodafone simlocked diamond v 1.37 etc and I cannot get any firmware upgrade installed. I tried also Shine On 1.8. All seems to go well until the progess bar when it sticks at 0% and I have to reboot the device..

Any ideas?

Thanks Alex

[aamd01]

Great work, thank you.

[supermorph]

:-)keep up the good work

[MrNoob]

Hi, recently I unlocked my Hermes using this guide (http://forum.xda-developers.com/showthread.php?t=293665)

which has olipro 1.4 installed, do I need to bother with the v7 2.10 in order to download this (http://www.4winmobile.com/forums/htc-hermes/11170-official-o2-uk-wm6-trion-hermes-rom-3-54-206-1_6275-radio-1-47-3-8-2007-a.html#post210730)?


Thanks :)

[italoparente]

Hi, Olipro.
I saw your post, it´s fantastic work.

I have a 8525, already read many posts cause I would like to up from wm6 to wm6.1, tried to flash jumpspl, hardspl and run some roms that I found, but there´s no way to me, I thnk that´s cause I am stupid.
When jumpspl, the device freeze.
When hard Spl on PC, comes error 260(connection failed).
When hard Spl on SD Card, nothing works.
Please, can you help me???

Thanks.

[abhii7]

new custom RUU is complete;

ROM Cookers, the good news is that this is now a single file, simply provide it with an NBH and you have compatibility with all SPL versions.

Fifth edition... with detection of all SPL versions, plus a very special selection of two soft-load options, including an "Unsafe" SPL which can be used to flash your device back to any SPL you desire.

5.2 is a small patch to fix an error with the unsafe SSPL not allowing you to overwrite the bootloader
i downloaded it and it say file corrupted

[patrick claassen]

HOW CAN I TO LET THE Sceptre Rom WORK ON MY HTC TOUCH PRO IS THAT POSIBLE BECAURCE IF I DO IT, IT NEVER BOOT AGAIN WHAT I DO WRONG CAN ANY ONE HELP ME PLEASE BECAURCE NO ONE WANT TO HELP ME HELLLLLLLLLLLLLLLLLLPPPPPPPPPPPPPPPPPPPPPPPPPPP

[setuptool]

it seems.....:D

[GASAN786]

explain this for me not understanding so nicely
bootmode(tri colour screen) when powered up and it displays
herm200
ipl-1.04

herm200
spl-2.03

what does this mean and how do i resolve this..:confused:

[GASAN786]

help me out here htc herm200 in boot mode(tri colour screen) active sync does not see the phone,so even if i do any form of update it does not want work as it gives error 260/240 basically just errors all the time,but mostly error 260

[GASAN786]

quote:how can I start the flash rom manually directly to the bootloader on my device?

Htc Tytn
IPL 1.04
SPL 2.03

this is exactly what I have but my phone stays in boot mode maybe some one out there can help us as I have posted this many time but nobody gives me working result

[the_tm]

Great work, guy! (as usual )

[l2bukast]

The RUU ends on 1% and says it can't be used on your phone, check your Update Utility... What sould I do? Uptate directly from the micro sd doesnt work either. It just doesn't start..

[kaal123]

isit gonna erse my SIMLOCK ERROR ?
and and would it reset my try with count 1 ?

[DackParis]

Okay So I'm trying to flash Leo_RADIO_2.12.50.02_2

I have it in the same folder with Custom RUU & Renamed to RUU_Signed.nbh
I have SPL-2.08.HSPL.
I have tried running RUUWrapper.exe with the phone in Bootloader and fully booted.

When I launch CustomRUU and Select Auto detect and check the box for "Is it Hard SPL?"

I get the Error "Error, Unknown Version! You should pick Safe SSPL"

Is there another way to flash it or am I missing something. . .

[pebrey]

Hi,

Just tried upgrading the radio on my HD2 using the above and now on boot I am getting error messages, and once booted I cant get any programs to run (At least, nothing I have installed - opera etc still works). I also cant view or connect wireless networks.

Phone details:

OS Version: 5.2.21869 (21896.5.0.82)
Mainla Version: 2.5.19211619.0
ROM Version: 1.66.405.2 (76641) WWE
Radio Version: 2.12.50.02_2
Protocol version: 15.40.50.07U
SPL: 2.08.HSPL

Was working fine until I applied the updated radio version this morning. To update, I ran RRU Wrapper with the above radio version. RUU Wrapper wouldnt detect the SPL, so I ran it in "Force safe SPL" mode. First attempt failed (With phone booted into Windows). Booted phone into update mode (Volume down / reset) and re-ran RRU Wrapper - went through pretty quickly and completed properly.

The error I get (Including a couple of these on boot) whenever I try to run anything is: The file '<filename>' cannot be opened. Either it is not signed with a trusted certifercate, or one of its components cannot be found. If the problem persists, try reinstalling or restoring this file.

Just wondering what to do next. Do I restore the original HTC ROM? The phone is on Virgin mobile in the UK...

Any help much appreciated.

Paul

[pebrey]

...My mistake - wireless is working - its just anything that wasnt on the original ROM. I also cant re-install any apps or run any other program (Including android!).

[pebrey]

Sorry - was panicing without actually finishing what I started. Loaded the Cookie energy ROM and all working fine (Including Android). That said, the Energy ROM is so damn good I'm not sure I need android after all!!!!

Guess its still windows....

[kingsaber]

How did you create this app , (RUUWrapper.exe) this is a masterpiece. Extract and retract after use. Brilliant!!!

[sunnykhan000]

Custom RUU 3.6 released; this does nothing except make it a bit more noob friendly.
HAY BRO i have htc touch dual NEON300 & i need a updated / cooked rom with video calling can u help me pleeeeez

[SteIIo]

Whenever I click to download the attachment i get 'attachment' or something of that nature and it won't give me the real attachment, just a php file, can you upload it to a mirror site? Thank you!

[knight76]

thcxthcxthcx