Need help stuck in BL

[chrisryn]

I need help phone stuck in bootloader and its not registering the usb syn cable being attached I think i just need to set it to boot to os. Have HARD-SPL.

[chrisryn]

ok got usb working again but ruu says it can't find device. is that because its already because its already in bootloader?.


edit- did an info 8 in mtty and got this
Block 0x3A8(936) is BAD block !!!
Block 0x3A9(937) is BAD block !!!
Block 0x3AA(938) is BAD block !!!


EDIT- finally got home and was able to reflash os with sd card and phone works now.

[Muster]

but what did you do to be able to flash?
everytime I try to flash it enters the BL and hangs. Then it says it cannot update. I've got a 1.09 BL
thanks

[pof]

Read here:

http://forum.xda-developers.com/showthread.php?t=286755

[Muster]

giving more data:

which bootloader version on your device?
1.09
which rom on your device?
1.35.255.2
which RUU are u using?
HTC WWE version
which rom are u trying to flash?
2.11.255.1

[pof]

Bootloader 1.09 is not compatible with new RUU version inside HTC's 2.11.255.1 ROM.

If you just run the shipped exe file (without unpacking), it will first upgrade your bootloader to 1.11 using the old RUU, then launch the new RUU and flash your rom.

BTW, i suggest you to read the hardSPL thread (http://forum.xda-developers.com/showthread.php?t=296722) before attempting to upgrade ;)

[Muster]

Ok, now I noticed that incompatibilty and used HArd SPL to upgrade to 1.11.
that's what it says now in threecolor bootloader.

But still when I try to upgrade it hangs on the bootloader saying HERM200 IPL-1.01 and HERM200 SPL-1.11 and USB in the white area. And in the PC it says OS information detecttion for ever!!

If I reboot it no problem, everything is working.

:(

thanks for you help!!

[pof]

ok, now that you have HardSPL-1.11 on your device, do this:

1. Use winrar to extract the contents of RUU_Hermes_QTEK_WWE_2.11.255.1_102_6275_1.38.00.10 _108_Ship.exe

2. You will see a file named RUU_Inside.exe

3. Use winrar again to extract the contents of RUU_Inside.exe

4. Run the RUU you'll find here, with device in bootloader mode.

Keep in mind that this will overwrite HARD-Spl with the shipped 1.11 bootloader, if you don't want that, read the wiki:

http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeGuide

[Muster]

Well it worked!!! Thanks a lot!!!! any explanation for this? (i forgot to tell I was using vista)

But... eheheh now I found out http://forum.xda-developers.com/showthread.php?t=297849&page=2

and it happens the same.. when I run it... (after winraring the main file) it hangs on the BL! Damn!!!

[pof]

(i forgot to tell I was using vista)

boh! :rolleyes:

[Muster]

I know I know awfull mistake!!! :p

Why does this happens when I try to update? ANd why it worked the way you said it would?

[Olipro]

Ok, now I noticed that incompatibilty and used HArd SPL to upgrade to 1.11.
that's what it says now in threecolor bootloader.

But still when I try to upgrade it hangs on the bootloader saying HERM200 IPL-1.01 and HERM200 SPL-1.11 and USB in the white area. And in the PC it says OS information detecttion for ever!!

If I reboot it no problem, everything is working.

:(

thanks for you help!!

uhh... it should say SPL-1.11.Oli

[Muster]

It did not!! It says now 1.11!!
when I tried the upgrade to WM6 it used it's own bootloader 1.09 Ds and it changed again. Is it possible that 1.09 BL is definitevely not working in my TyTN?