HTC Apache Audiovox PPC6700 LCD / Digitizer Replacement Instructions

[bullcrap420]

All I have right now is this from someone online who said he had the instructions. If anyone has clear outlined pictures to do this, please post it.

Thank you!


"There are additional screws that need to be taken out. You have to pop off the housing on the top that covers the camera and the antenna port. there will be at least 2 more screws there. Then you will carefully have to pop off the back starting at the bottom by where the stylus is and pull that off. There is probably going to be another screw holding the board in place. It has been a few months since i have done this. Then the board comes out and you have 4 more screws these are phillips heads. That will take the back housing off of the front. Then 4 more screws to take the back plate off of the front housing."

[bullcrap420]

The Audiovox PPC-6700 I have has a cracked screen. I got an LCD replacement, but have no detailed instructions on removing the cracked screen. Here are some useful places i've looked at to find the answer to this issue if it helps you:

http://forum.xda-developers.com ... of course why else would I post it here :)

http://buzzdev.net/component/option,com_simpleboard/Itemid,59/func,view/id,9459/catid,59/limit,15/limitstart,0/index.php?option=com_phorum&Itemid=125

http://forum.brighthand.com

http://www.mobiletechreview.com/ubbthreads/ubbthreads.php

[bullcrap420]

Here are my own instructions I started... maybe someone else can expand/refine/clean this up. I'm done with this finally. Changing this is possible, but not necessarily easy. There's this tinny like sticker on the OEM LCD in the phone that's a real pain to pull off of the LCD. The pictures are terrible too...sorry...again..something= better than nothing. :)

In the end, it works...everything except my toggle does not click in like it used to...that's probably because of that rubber piece I did not know about. (A rubber piece fell out when I was taking it apart and I never figured out where it was supposed to go..so if anyone knows where that belongs and how it should be oriented..please post it.)

I took the stylus out.
I took the miniSD plastic blank out/ or miniSD memory card out just in case.
I took the battery cover off.
I took the battery out.
I set the camera lens in between the picture of the flower and the sun in the back.
I took the rubber piece out..there's a little probe looking thing behind it. (Probably was not necessary to take out.)
I took the back camera cover off. (Remove two Philips head screws with a PH0 head.) There are 7 notches holding it in place. [One above sun/flower adjuster, one slightly to the right above the flash hole, one above the rubber piece, one a tiny bit below the rubber piece, 2 on the insides at the bottom of the philips head screws, and one to the right of the speakerphone.]
I took the green circuit board that has camera flash behind the camera cover off. (Pops up off slot after removing one philips head screw.)
I took the camera unit off. (Do not pull up on camera, just pull the green board up off. The camera is sitting there, the board is wired like the camera flash board was plugged in, just pop it off.)
I took the cell phone antenna philips head screw off that is above where the camera was.
I took the 4 torx .050 allen head type size screws out to remove the back plastic cover of the phone off. Be very careful prying this portion apart. There are probably about 14 notches maybe that holds the back plate on. Some say to start trying to pry it apart from the antenna, but I was able to pry it apart from the bottom part of the phone on the antenna side... not where the antenna is. Be extremely careful how you pry this apart. You have to watch out for the speakerphone wires, there is a plug for what I think might be the keyboard and or LCD, the vibrating weight, and the main board itself... you don't want to scratch or sever any of these parts.
I slid the antenna off of the main board. Lift the board and gently pull up and out the black antenna.
I did not take the speakerphone off, but it looks like you have to pull the wire from the board that would still be attached to the back plate. The vibrating weight is also on the backplate.
I took the main board out of the phone. Keep the slider in mind between the IE button and the recorder button on the side of the phone. The black portion on the main board needs to line up with the actual switch you would slide up or down with your thumb on the side of the phone. When pulling the main board out, slide open the keyboard fully/halfway. Watch for a black rubber piece.
I removed the 4 philips head screws that hold the keyboard portion of the phone to the LCD portion of the phone together and lifted them apart. There is a silver/grey tape that you need to pop up the data cable and pull the tape off to completely separate the LCD portion.
I removed the 4 torx screws from behind the LCD screen and carefully took the LCD portion apart.

...ok well it's getting quite annoying to try and write everything I did after this, but it's pretty self explanatory. If it's not, you probably should not be changing your LCD in the first place anyhow. In order to release the LCD ribbon, the plastic piece at the end will need to pop up at an angle..it's kind of like a winch.


Here's a similar phone that gets taken apart if that helps you out in any way.
.........http://www.mdatweak.com/downloads/Wizard_Service_Manual.pdf

Pix 1-5 of 21 attached.

[bullcrap420]

Pix 6-10 of 21 attached.

[bullcrap420]

Pix 11-15 of 21 attached.

[bullcrap420]

Pix 16-20 of 21 attached.

[bullcrap420]

Pix 21 of 21 attached.

[sankekur]

what is the toggle you are refering to? i took mine apart to clean around the screen without any instructions, and everything still works, but the digitizer has had it, where did you get your replacement from?

[bullcrap420]

I got my replacement from eBay. goldelec (http://myworld.ebay.com/goldelec)

The LCD had a weird rainbow thing going on in the center of it, that you can see if you look at it at the right angle and the bottom corner looks bright white when the screen is on for an extensive period of time. Again, it works...better than what I had. I did not get great instructions, but what he sold me worked fine.

The toggle i'm talking about is the button in between the call and hangup buttons on the front face of the phone. That toggle switch just does not seem connected or stiff like it used to be. I can't "click" up/down/left/right or select anything. I am convinced the rubber piece goes behind it somewhere somehow. I just have to take it apart and figure out the orientation of it.

[jksuperstar]

thanks for these pics & instructions, I just replaced with a part from goldelec on ebay as well (though the auction list instructions as part of the deal, they didn't come with my shipment, so your play-by-play was invaluable)...and there's no screws left afterward! Always a good sign.

[oplitic]

Maybe this will help some people...

http://wiki.ppcgeeks.com/index.php?title=How_To:Disassemble_your_6700

[belize2004]

www.htclcd.com has a lot of good lcd replacement instructions also
as well as the LCD's