stuck in new 3.03.0000 bootloader [Archive]

theovdb

12th July 2007, 01:32 PM

Hi,

I tryed to upgrade to WM6 but I think I tit someting wrong, I flasht my
old WM5 back but now it is not possible to try flashing to WM6.
stuck in new 3.03.0000 bootloader.

I hope somebody can help me, thanks

Theo

racerx_

12th July 2007, 02:47 PM

are you stuck in bootloader, or were you successful in flashing WM5 ROM? also, please please PLEASE read the threads in this forum before posting. You are the millionth customer to post this issue

shym

12th July 2007, 02:59 PM

Come on guy, if you can write, i suppose that you can read HERE (http://forum.xda-developers.com/showthread.php?t=316233) ... ;)

theovdb

12th July 2007, 03:44 PM

are you stuck in bootloader, or were you successful in flashing WM5 ROM? also, please please PLEASE read the threads in this forum before posting. You are the millionth customer to post this issue

I was success full in flashing the WM5 rom back on the device, now I am trying to install hard SPL and WM6 as describe on TRINITYGUIDES.INFO but stuck by the start.
Hard SPL will not flash I see on my Red,Green,Blue screen IPL-SSPL, SPL-1.07.ds , yes I am new with this matter an my English is not too well but please.:(

racerx_

12th July 2007, 04:29 PM

please state what the problem is when you try to flash

theovdb

12th July 2007, 04:55 PM

please state what the problem is when you try to flash

When I start to flash the sync. is oke but when the bootloader screen appears the flashing stops and the PDA is not connected anymore.:(

shym

12th July 2007, 05:01 PM

Try to launch again your update while you're in bootloader mode...It should work !!

theovdb

12th July 2007, 05:14 PM

Try to launch again your update while you're in bootloader mode...It should work !!

I just did it but when my device is in bootloader mode there is now
connection with my notebook (VISTA) anymore. When I restart my
PDA the connection is established.:(

racerx_

13th July 2007, 01:33 AM

there is a wiki guide to flashing under vista..

please note, that when you start the updater, and your device goes in to bootloader, it times out. So connection is lost. Simply start the update again, with device still connected in bootloader

theovdb

13th July 2007, 09:14 AM

there is a wiki guide to flashing under vista..

please note, that when you start the updater, and your device goes in to bootloader, it times out. So connection is lost. Simply start the update again, with device still connected in bootloader

Yes I did already as you describe the result is still no connection (error).:(

racerx_

13th July 2007, 09:21 AM

hmm... i think you're gonna have to use Pof's splxploit (http://forum.xda-developers.com/showthread.php?t=308691) to load hard-spl and then flash another ROM from there.

stepw

14th July 2007, 04:57 AM

It's a question of whether SPL 3.03 is exploitable in the same way...

itlinux

14th July 2007, 05:01 AM

I was success full in flashing the WM5 rom back on the device, now I am trying to install hard SPL and WM6 as describe on TRINITYGUIDES.INFO but stuck by the start.
Hard SPL will not flash I see on my Red,Green,Blue screen IPL-SSPL, SPL-1.07.ds , yes I am new with this matter an my English is not too well but please.:(

you need to use the active sync after you load wm5 ... that's the trick..

banzro

14th July 2007, 08:40 AM

Hello,

I have allways start the update twice, Once where the device starts in this 3-Colors boot screen and a second time to start the Flashing process.

Do not tuch the device Just clos update application on Windows PC and restart it and go through the question process until it starts to flash

Hope it helps for you

Robidog

theovdb

14th July 2007, 09:07 AM

Hello,

I have allways start the update twice, Once where the device starts in this 3-Colors boot screen and a second time to start the Flashing process.

Do not tuch the device Just clos update application on Windows PC and restart it and go through the question process until it starts to flash

Hope it helps for you

Robidog

Thanks guys for all your help but the problem still exists, I keep looking
to this forum and hope in time the problem will be solved.

Thanks a lot :)

banzro

14th July 2007, 09:36 AM

Thanks guys for all your help but the problem still exists, I keep looking
to this forum and hope in time the problem will be solved.

Thanks a lot :)
Hello,

Explain me the Problem a bit more cloaser (step by step what you are doing)
error messages, and also what image you had bevore on it, I need also to know which which version is written on the 3-colored screen...

Look forward to her from you...

racerx_

14th July 2007, 02:56 PM

It's a question of whether SPL 3.03 is exploitable in the same way...

the answer is yes, splxploit works in new bootloader too.

theovdb

16th July 2007, 08:43 AM

the answer is yes, splxploit works in new bootloader too.

the answer is no splxploit not works on SPL 3.03 on my device

shym

16th July 2007, 12:30 PM

So what did you do to fix this ??

theovdb

16th July 2007, 08:13 PM

So what did you do to fix this ??

On this moment nothing, I did something wrong by flashing the first time
and now I am stuck in SPL 3.03. I think the best what I can do is waiting for
the official rom from HTC.:(

racerx_

17th July 2007, 01:19 AM

the answer is no splxploit not works on SPL 3.03 on my device

what happens when you run the xploit program?

theovdb

17th July 2007, 10:46 AM

what happens when you run the xploit program?

Guys I solved the problem, on my Vista notebook it downed worked out but on the old notebook XP from my fam. it works and I used the Sim_Cid unlock_
V1. Now I am running the WM6 D810.

Thanks for helping me:) :) :)

theovdb

17th July 2007, 10:48 AM

Guys I solved the problem, on my Vista notebook it downed worked out but on the old notebook XP from my fam. it works and I used the Sim_Cid unlock_
V1. Now I am running the WM6 D810.

Thanks for helping me:) :) :)

Thanks again