DOPOD WM6 official and VOIP problems [Archive]

View Full Version : DOPOD WM6 official and VOIP problems

lellobello

13th July 2007, 07:05 PM

VOIP seems to be blocked on the new HTC official WM6 release for DOPOD.

Tried to reinstall the required dll through the usual .cab (used before roms cooks stopped removing WM6 VOIP functionalities), and the Internet Calling features appear on today's screen, however it's impossible to have the service working.

Tried the settings .cab I created (always worked with past WM6 roms) and the a program SIPconfigToll (ver. 2.0.1), but none seems to apply the settings and
always receive the same message: Internet Calling: Service Blocked. (not even the service name seems to change).

Any advice?

Internet connection is ok as well as ports, etc.

eva_d

13th July 2007, 07:47 PM

Tried the settings .cab I created (always worked with past WM6 roms) and the a program SIPconfigToll (ver. 2.0.1), but none seems to apply the settings and
always receive the same message: Internet Calling: Service Blocked. (not even the service name seems to change).

I've installed these two cabs:
MajikVOIP.cab - http://www.4winmobile.com/forums/local_links.php?action=jump&id=24&catid=6
VOIP Drivers.cab from http://wmblack.info/addons/

And VoIP is working fine for me with official WM6 ROM. :)

lellobello

14th July 2007, 12:57 AM

sweet

works fine now

thanks a lot

makhou

14th July 2007, 03:14 AM

Hi,
I install fisrt MajikVOIP.cab by double click. Let me know the way to install VOIP Drivers.cab?

lellobello

14th July 2007, 04:04 AM

double click again?

Don't forget to restart after installation

TecMan45

14th July 2007, 07:02 PM

alexng167

14th July 2007, 08:10 PM

I've installed these two cabs:
MajikVOIP.cab - http://www.4winmobile.com/forums/local_links.php?action=jump&id=24&catid=6
VOIP Drivers.cab from http://wmblack.info/addons/

And VoIP is working fine for me with official WM6 ROM. :)
hi eva_d, I haven't permission for download MajikVOIP.cab. can you provide other link for download? many thanks!

eva_d

15th July 2007, 01:17 AM

1. I installed MajikVOIP.cab in my microSD
2. I installed VOIP Drivers.cab in my microSD
3. Restart
3. I installed SetupVoIP_v0.3 from Schap (it has proxy, SipConfigTool_2_0_1 doesn't have it)
4. I done my personal settings with SetupVoIP_v0.3

and the Internet Calling done the following:

Searching...and then...No-Service

Did you try to reinstall VoIP app in device memory? Did VoIP work for you before? Do you have WiFi switched on? Does your provider/router/firewall block any VoIP ports? I would start with these things first, surely.

eva_d

15th July 2007, 01:17 AM

hi eva_d, I haven't permission for download MajikVOIP.cab. can you provide other link for download? many thanks!

Register an account on 4winmobile.com, and then you'll have an access. Simple as that.

maymaymay

15th July 2007, 02:16 PM

hi eva_d, I haven't permission for download MajikVOIP.cab. can you provide other link for download? many thanks!
Try this, if they are the same files :
http://forum.xda-developers.com/attachment.php?attachmentid=43949&d=1184484873

TecMan45

15th July 2007, 04:33 PM

Hi eva_d:

Thanks for your reply...let me give you my answers:

Did you try to reinstall VoIP app in device memory?
- No, I installed MajikVOIP.cab & VOIP Drivers.cab only in my microSD
- Do you recommend me to install them in device memory?

Did VoIP work for you before?
- Yes, I installed a few days ago, SJ-Labs - SJphone-PPC2003-303c and it worked fine with my VoIP provider

Do you have WiFi switched on?
- Yes, it's a basic...No-VoIP without WiFi

Does your provider/router/firewall block any VoIP ports?
- If SJ-Labs - SJphone-PPC2003-303c worked with my VoIP-Settings, I supposed that I don't have problems with block any VoIP ports

What are your recommendations to fix my problem?

Thanks

TecMan
HTC TyTN
HERM200 IPL-1.04
HERM200 SLP-2.10.01ipro 2.10.Olipro

Device Information (Upgraded 7-13-07)
ROM version: 3.54.707.3
ROM date: 07/05/07
Radio version: 1.47.00.10 (Upgraded 7-11-07)
Protocol version: 32.80.7020.20H (Upgraded 7-11-07)

Windows Mobile 6 Professional
CD OS 5.2.1437 (Build 17944.0.3.1)

philjohn

15th July 2007, 05:19 PM

always install OS specific files in main memory.

I actually store all apps in main memory and just use the microsd for data

alishankiti

15th July 2007, 05:49 PM

I've installed these two cabs:
MajikVOIP.cab - http://www.4winmobile.com/forums/local_links.php?action=jump&id=24&catid=6
VOIP Drivers.cab from http://wmblack.info/addons/

And VoIP is working fine for me with official WM6 ROM. :)

Can you please tell us who is your voip provider?
Thanks

eva_d

15th July 2007, 07:55 PM

Can you please tell us who is your voip provider?
Thanks

I'm using it with Polish ipfon.pl, however AFAIR it also worked witch sipgate.co.uk.

lellobello

15th July 2007, 08:05 PM

Mine is Messagenet. Excellent service.

www.messagenet.it

linker3000

16th July 2007, 10:34 PM

Hi,

I've loaded MajikVOIP.cab, VOIP Drivers.cab and SetupVoIP_v0.3 (all in main memory) and although VoIP works OK, I get the occasional, short bursts of crackling from the loudspeaker, even when it's not actually enabled.

Is this a Known 'feature'?

System specs in sig.

Thanks

eva_d

16th July 2007, 10:59 PM

eva_d

17th July 2007, 11:31 AM

I've loaded MajikVOIP.cab, VOIP Drivers.cab and SetupVoIP_v0.3 (all in main memory) and although VoIP works OK, I get the occasional, short bursts of crackling from the loudspeaker, even when it's not actually enabled.

I just placed VoIP call, and you're right - there is that crackling sound coming out of external speaker from time to time. :( However, I don't have this when VoIP is disabled. :-o

Btw, do you have the same 'feature' that changing in-call volume with roller is not possible while VoIP call?

linker3000

17th July 2007, 02:07 PM

I just placed VoIP call, and you're right - there is that crackling sound coming out of external speaker from time to time. :( However, I don't have this when VoIP is disabled. :-o

Btw, do you have the same 'feature' that changing in-call volume with roller is not possible while VoIP call?

Let me try....

Confirmed, I can't change volume with the roller too.

Black Bear

17th July 2007, 09:59 PM

Im in the same problem, I Black Majik and I can't get VOIP to work. Please Can some one tell me the best combination to use. thx

kidd78

29th August 2007, 11:47 AM

anyone found a solution to the crackling sound ? i getting this problem too.

JenkinsBarry

30th August 2007, 03:55 AM

I have no problem installing the internet calling drivers but I have NO idea how to input the settings in the "Setup VOIP" program. I have Vonage as an Internet Phone Service...Does anyone know a link where the settings are given so I can actually use the VOIP program?

It would be very helpful when I am out of town to still use my 8525 but not use "out of town" minutes..just getting on through wifi would be awesome!

kidd78

30th August 2007, 07:57 PM

http://www.vonage-forum.com/ftopic4260.html

amazing tool google

jeRrRKKKK

30th August 2007, 08:57 PM

anybody from singapore managed to get pfingo to work with this?

JenkinsBarry

30th August 2007, 11:48 PM

Thanks for the help Kidd78...Yeh I googled it before I asked...but I guess I did not put the right phrase in..

Since I am in a post already, let me vent a lil bit...Does anyone know why people are SOOOO rude on these forums? I hope they are not this way in real life...I feel sorry for them if they are....they must be very miserable people.. Anyway...a little bit of patients and common courtesy can go a long way!

kidd78

31st August 2007, 12:52 PM

Sorry if that’s ment to be at me but I was on my phone when I replied to that, but I do know that there are some very rude people out there and that’s just a superior complex. It’s more than likely that we are junior members and we don’t know much compared to the longer members.

It makes it harder to ask for help if these harsh members bitch at you, so with this I make sure I research it hard i.e. Google or search forums with every phrase I can think of before I am stumped and ask for help.

I know that some questions will be asked again and again but we all human we need to learn from our mistakes

But have to say its not just this forum its most others i have been to ie psp-hacks but this is full of jumped up little brats

agaviani

9th September 2007, 01:06 PM

Mine is Messagenet. Excellent service.

www.messagenet.it

Lellobello,
can you please give some indication on how to use messagenet?
I created an account adn got a freenumber but how can I receive the call in the HTC Hermes WM6?
Do I need to download a special sw instead of using WM6 "internet calling"?

ressayflex

15th October 2007, 06:45 PM

So i have looked through about 100 pages of forums to try to find the answer.... and who knows maybe it just doesnt work. i would like to know if anyone has been successful at getting voip to connect over 3G? i can get it to work no problems over wifi (even though i have had different results on different access points).

i am using an AT&T tilt, i have tried using wap.cingular, and isp.cingular, disabled my proxy, an set the registry to allow 3G voip, etc... i am curious to know if anyone has done this successfuly on the AT&T/cingular network.

your replies are greatly appreciated!

thanks!

stufried

17th October 2007, 04:09 PM

Can you make a voip call over wifi?

zdtouch

8th December 2007, 05:57 PM

Hi Friends:

I have a HTC TyTN with the last Official DoPoD WM6 WWE ROM 3.54.707.3...I'm trying to install the Internet Calling...here are my procedure:

1. I installed MajikVOIP.cab in my microSD
2. I installed VOIP Drivers.cab in my microSD
3. Restart
3. I installed SetupVoIP_v0.3 from Schap (it has proxy, SipConfigTool_2_0_1 doesn't have it)
4. I done my personal settings with SetupVoIP_v0.3

and the Internet Calling done the following:

Searching...and then...No-Service

Can you help me please?

Thanks

TecMan
HTC TyTN
HERM200 IPL-1.04
HERM200 SLP-2.10.01ipro 2.10.Olipro

Device Information (Upgraded 7-13-07)
ROM version: 3.54.707.3
ROM date: 07/05/07
Radio version: 1.47.00.10 (Upgraded 7-11-07)
Protocol version: 32.80.7020.20H (Upgraded 7-11-07)

Windows Mobile 6 Professional
CD OS 5.2.1437 (Build 17944.0.3.1)

I am using HTC Touch and for me is working fine (Over Wi-Fi)

I used SetupVoIP_v0.3 and I was experiencing exactly the same problems until I uninstalled it.
I installed SipConfigTool_2_0_1 and the files (MajikVoIP, VOIP Drivers, SIPConfigTool) on the device memory and not ! on the microSD card.
Try to use SipConfigTool, and enter only the SIP address of your VOiP provider and see if it works.
The stun address of VoipDiscount is stun.voipdiscount.com and for me it works fine without entering it and I am using only the sip.voipdiscount.com
(I have tested it also with SJphone where I removed the stun address and it works)

- For VoIP calls using Wi-Fi connection follow the steps 1 to 13:
(Tested and working on my phone)

- For VoIP calls using 3G/GSM follow the steps 1 to 12 and 14 to 16
(I haven't tested it)

----------------------------------------------------------------------------------------

1. Instsall MajiikVoip.CAB (on your device memory ! not on microSD card)
2. Install VOIP Drivers (on your device memory ! not on microSD card)
3. Restart your phone
4. Go to 'Start' -> 'Settings' -> select 'Personal' -> Phone
5. Select 'Internet' -> select Internet Calling 'Whenever available' from the list
6. Install SipConfigTool_2_0_1 (on your device memory ! not on microSD card)
7. Run SipConfigTool_2_0_1

The following Settings are to set up VoipDiscount as your VoIP provider

8. Description : VoipDiscount
9. Sip Server : sip.voipdiscount.com
10.Port : 5060
11.User Name : your_username_here
12.Password : your_password_here
13. Click 'Save Sonfiguration' button

----------------------------------------------------------------------------------------

14. Click Tools -> Sip Over 3g/Gsm -> Select 'Enable Via Reg'
15. Click 'Save Sonfiguration' button
16. Restart your phone.

----------------------------------------------------------------------------------------

- If you have done everything correctly then at the end you
should be able to see on your Today screen
VoipDiscount: Available

http://img250.imageshack.us/img250/8338/pccapture6ot1.png

- Tap where it says VoipDiscount: Available and you should be able to see:
VoipDiscount: Selected
http://img88.imageshack.us/img88/2963/pccapture2yv1.png

- When you dial make sure you use 00 instead of '+'
http://img88.imageshack.us/img88/8752/pccapture5kb8.png

If you want to be able making calls using '+' You will need to replace the script of dialplan.xml from your phone's windows folder with the following:

<dialplan xmlns='http://schemas.microsoft.com/embedded/VoIP'>
<dialplan-header>
<host>#use_sipsrv_host_name#</host>
</dialplan-header>

<rule pattern='(\d+)'
dial='sip:\1@$host$'
display='\1'
transfer='sip:\1@$host$'
/>


<rule pattern='\d{1,3}\.\d{1,3}\.\d{1,3}\.\d{1,3}'
restrict='Cell,SMS'
/>
<rule pattern='(\d{1,3})\*(\d{1,3})\*(\d{1,3})\*(\d{1,3} )'
dial='\1.\2.\3.\4'
display='\1.\2.\3.\4'
transfer='\1.\2.\3.\4'
restrict='Cell,SMS'
/>

<rule pattern='\+\s*(\d+)?'
dial='sip:00\1@$host$'
display='00\1'
transfer='sip:00\1@$host$'
/>
<rule pattern='+\s*-?\s*$(\d{3})$\s*(\d{3})\s*-?\s*(\d{4})(\s*[Xx]\s*\d+)?'
dial='sip:00\1\2\3@$host$'
display='00 (\1) \2-\3'
transfer='sip:00\1\2\3@$host$'
/>
<rule pattern='\+\s*1\s*-?\s*(\d{3})\s*(\d{3})\s*-?\s*(\d{4})(\s*[Xx]\s*\d+)?'
dial='sip:00\1\2\3@$host$'
display='00 (\1) \2-\3'
transfer='sip:00\1\2\3@$host$'
/>
<rule pattern='\+\s*1\s*-?\s*$(\d{3})$\s*(\d{3})\s*-?\s*(\d{4})(\s*[Xx]\s*\d+)?'
dial='sip:00\1\2\3@$host$'
display='00 (\1) \2-\3'
transfer='sip:00\1\2\3@$host$'
/>

<rule pattern='(\d{3})\s*(\d{3})\s*-?\s*(\d{4})(\s*[Xx]\s*\d+)?'
dial='sip:\1\2\3@$host$'
display='(\1) \2-\3'
transfer='sip:\1\2\3@$host$'
/>
<rule pattern='$(\d{3})$\s*(\d{3})\s*-?\s*(\d{4})(\s*[Xx]\s*\d+)?'
dial='sip:\1\2\3@$host$'
display='(\1) \2-\3'
transfer='sip:\1\2\3@$host$'
/>

<rule pattern='[Ss][Ii][Pp][Ss]?:\s*(\d{3})(\d{3})(\d{4})@(.+)'
display='(\1) \2-\3'
restrict='Cell,SMS'
/>
<rule pattern='([Ss][Ii][Pp][Ss]?:)?\s*([a-zA-Z0-9_-]+)@(.+)'
display='\2'
restrict='Cell,SMS'
/>
<rule pattern='[Ss][Ii][Pp][Ss]?:\s*([^@]+)'
display='\1'
restrict='Cell,SMS'
/>

<rule pattern='(\d{3})-?(\d{2})'
dial='sip:\1\2@$host$'
display='\1\2'
transfer='sip:\1\2@$host$'
/>
<rule pattern='1\s*$(\d{3})$\s*(\d)'
dial='sip:1\1\2@$host$'
display='1\1\2'
transfer='sip:1\1\2@$host$'
/>

<rule pattern='(\d+)'
dial='sip:\1@$host$'
display='\1'
transfer='sip:\1@$host$'
/>
</dialplan>

----------------------------------------------------------------------------------------
Photos taken by psybill (http://www.myphone.gr/forum/showthread.php?t=189583)

----------------------------------------------------------------------------------------
[B]SipConfigTool_2_0_1.CAB http://www.freewareppc.com/communication/sipconfigtool.shtml
----------------------------------------------------------------------------------------

imus

9th December 2007, 12:53 AM

Let me try....

Confirmed, I can't change volume with the roller too.

I think its because its using your internet, not the phone. It really isnt "in call"

trandus

2nd June 2008, 11:52 PM

How can I configure VoIP on Smartphone (not PPC). SipConfigTool_2_0_1 and SetupVoIP_v0.3 don’t work :(.
I’ve got Vox with WM6.1.

thanks
trandus

prpsarathy

3rd June 2008, 10:31 AM

Hi,

Where do i get the voipdriver.cab and majik.cab. I tried with wm6voip.cab. I did everything as per the instruction. It is not working the way in which it is mentioned int he screen print.

regards, sarathy

deadbanana0717

24th June 2008, 07:45 AM

Hey guys, Ive been trying to get VOIP working for soooo long =(
Skype works but i dont think its the same thing we're talking about here.
I looked around and found a company similar to skype called "Vbuzzer" and they also have the SIP function.

Long story short, I installed the following

HTC TyTN
Mobile 6 (Black 3.1)
MajikVOIP.cab
VOIP Drivers.cab
SipConfigTool_2_0_1
SetupVoIP_v0.3

The service seems to work execpt that i cannot hear anything through my blue tooth head set.
Also all numbers must be dialed with +1 (area code) etc. is this common?

THanks!

ntn555

5th December 2009, 10:31 PM

I am using HTC Touch and for me is working fine (Over Wi-Fi)

I used SetupVoIP_v0.3 and I was experiencing exactly the same problems until I uninstalled it.
I installed SipConfigTool_2_0_1 and the files (MajikVoIP, VOIP Drivers, SIPConfigTool) on the device memory and not ! on the microSD card.
Try to use SipConfigTool, and enter only the SIP address of your VOiP provider and see if it works.
The stun address of VoipDiscount is stun.voipdiscount.com and for me it works fine without entering it and I am using only the sip.voipdiscount.com
(I have tested it also with SJphone where I removed the stun address and it works)

- For VoIP calls using Wi-Fi connection follow the steps 1 to 13:
(Tested and working on my phone)

- For VoIP calls using 3G/GSM follow the steps 1 to 12 and 14 to 16
(I haven't tested it)

----------------------------------------------------------------------------------------

1. Instsall MajiikVoip.CAB (on your device memory ! not on microSD card)
2. Install VOIP Drivers (on your device memory ! not on microSD card)
3. Restart your phone
4. Go to 'Start' -> 'Settings' -> select 'Personal' -> Phone
5. Select 'Internet' -> select Internet Calling 'Whenever available' from the list
6. Install SipConfigTool_2_0_1 (on your device memory ! not on microSD card)
7. Run SipConfigTool_2_0_1

The following Settings are to set up VoipDiscount as your VoIP provider

8. Description : VoipDiscount
9. Sip Server : sip.voipdiscount.com
10.Port : 5060
11.User Name : your_username_here
12.Password : your_password_here
13. Click 'Save Sonfiguration' button

----------------------------------------------------------------------------------------

14. Click Tools -> Sip Over 3g/Gsm -> Select 'Enable Via Reg'
15. Click 'Save Sonfiguration' button
16. Restart your phone.

----------------------------------------------------------------------------------------

- If you have done everything correctly then at the end you
should be able to see on your Today screen
VoipDiscount: Available

http://img250.imageshack.us/img250/8338/pccapture6ot1.png

- Tap where it says VoipDiscount: Available and you should be able to see:
VoipDiscount: Selected
http://img88.imageshack.us/img88/2963/pccapture2yv1.png

- When you dial make sure you use 00 instead of '+'
http://img88.imageshack.us/img88/8752/pccapture5kb8.png

If you want to be able making calls using '+' You will need to replace the script of dialplan.xml from your phone's windows folder with the following:

<dialplan xmlns='http://schemas.microsoft.com/embedded/VoIP'>
<dialplan-header>
<host>#use_sipsrv_host_name#</host>
</dialplan-header>

<rule pattern='(\d+)'
dial='sip:\1@$host$'
display='\1'
transfer='sip:\1@$host$'
/>


<rule pattern='\d{1,3}\.\d{1,3}\.\d{1,3}\.\d{1,3}'
restrict='Cell,SMS'
/>
<rule pattern='(\d{1,3})\*(\d{1,3})\*(\d{1,3})\*(\d{1,3} )'
dial='\1.\2.\3.\4'
display='\1.\2.\3.\4'
transfer='\1.\2.\3.\4'
restrict='Cell,SMS'
/>

<rule pattern='\+\s*(\d+)?'
dial='sip:00\1@$host$'
display='00\1'
transfer='sip:00\1@$host$'
/>
<rule pattern='+\s*-?\s*$(\d{3})$\s*(\d{3})\s*-?\s*(\d{4})(\s*[Xx]\s*\d+)?'
dial='sip:00\1\2\3@$host$'
display='00 (\1) \2-\3'
transfer='sip:00\1\2\3@$host$'
/>
<rule pattern='\+\s*1\s*-?\s*(\d{3})\s*(\d{3})\s*-?\s*(\d{4})(\s*[Xx]\s*\d+)?'
dial='sip:00\1\2\3@$host$'
display='00 (\1) \2-\3'
transfer='sip:00\1\2\3@$host$'
/>
<rule pattern='\+\s*1\s*-?\s*$(\d{3})$\s*(\d{3})\s*-?\s*(\d{4})(\s*[Xx]\s*\d+)?'
dial='sip:00\1\2\3@$host$'
display='00 (\1) \2-\3'
transfer='sip:00\1\2\3@$host$'
/>

<rule pattern='(\d{3})\s*(\d{3})\s*-?\s*(\d{4})(\s*[Xx]\s*\d+)?'
dial='sip:\1\2\3@$host$'
display='(\1) \2-\3'
transfer='sip:\1\2\3@$host$'
/>
<rule pattern='$(\d{3})$\s*(\d{3})\s*-?\s*(\d{4})(\s*[Xx]\s*\d+)?'
dial='sip:\1\2\3@$host$'
display='(\1) \2-\3'
transfer='sip:\1\2\3@$host$'
/>

<rule pattern='[Ss][Ii][Pp][Ss]?:\s*(\d{3})(\d{3})(\d{4})@(.+)'
display='(\1) \2-\3'
restrict='Cell,SMS'
/>
<rule pattern='([Ss][Ii][Pp][Ss]?:)?\s*([a-zA-Z0-9_-]+)@(.+)'
display='\2'
restrict='Cell,SMS'
/>
<rule pattern='[Ss][Ii][Pp][Ss]?:\s*([^@]+)'
display='\1'
restrict='Cell,SMS'
/>

<rule pattern='(\d{3})-?(\d{2})'
dial='sip:\1\2@$host$'
display='\1\2'
transfer='sip:\1\2@$host$'
/>
<rule pattern='1\s*$(\d{3})$\s*(\d)'
dial='sip:1\1\2@$host$'
display='1\1\2'
transfer='sip:1\1\2@$host$'
/>

<rule pattern='(\d+)'
dial='sip:\1@$host$'
display='\1'
transfer='sip:\1@$host$'
/>
</dialplan>

----------------------------------------------------------------------------------------
Photos taken by psybill (http://www.myphone.gr/forum/showthread.php?t=189583)

----------------------------------------------------------------------------------------
[B]SipConfigTool_2_0_1.CAB http://www.freewareppc.com/communication/sipconfigtool.shtml
----------------------------------------------------------------------------------------
No 3G can use EDGE?Thanks!!!

dhillonbros

18th May 2010, 04:21 AM

http://forum.xda-developers.com/showthread.php?t=596682 . d