hold comm to vibrate?

[mixmaven]

Anyone figured out how to map to a different button? This is the one feature i miss.

-mix

[wpbear]

Anyone figured out how to map to a different button? This is the one feature i miss.

-mix

Does this work?

[mixmaven]

That is what I tried, but there isn't a comm button on the Kaiser... It didn't work on any of the buttons I found. Does anyone know the reg key? we could probably change it to the ok/close button instead. I emailed kyphur to see if he knows...

-mix

[wpbear]

That is what I tried, but there isn't a comm button on the Kaiser... It didn't work on any of the buttons I found. Does anyone know the reg key? we could probably change it to the ok/close button instead. I emailed kyphur to see if he knows...

-mix

Use "Vibra Switch" then Do a seach its on XDA.

[niralisse]

Use "Vibra Switch" then Do a seach its on XDA.

I tried this, and it's a good concept, except the AT&T ROM doesn't expose PTT as a possible button mapping, which means one of the existing start/PIE/messaging/ok/camera buttons would have to be sacrificed for a vibe toggle.

The superfluous PTT button is the obvious candidate for a vibrate toggle but sadly neither of the suggestions allow its use as such.

[wpbear]

I tried this, and it's a good concept, except the AT&T ROM doesn't expose PTT as a possible button mapping, which means one of the existing start/PIE/messaging/ok/camera buttons would have to be sacrificed for a vibe toggle.

The superfluous PTT button is the obvious candidate for a vibrate toggle but sadly neither of the suggestions allow its use as such.

As the 8525 was eventually hacked for the PTT button to be useful you will have to be patient. This device is new so it takes time.

[RemE]

This works fine, load Vibra Switch, it will place 2 apps in the programs folder "Vibra Switch" and "Vibra Switch Delayed" (you can delete that one). Then in Settings>buttons> Select button 6, the top-left button currently used for single-press=Voice Speed Dial, press-and-hold=Recorder, re-assign the "press-n-hold button to be "Vibra Switch" and you are done.

I've been listing my tweak tries in amother thread, I can't get Bluetooth to redirect all sounds out to headset and I also can't get vjay lumos III to make the display go super bright. With no transreflective screen, this is now a very important tweak to me, I hope these can be figured out.

[mixmaven]

ahhhhh sweet. you guys are great! :)

-mix

[spiro]

This works fine, load Vibra Switch, it will place 2 apps in the programs folder "Vibra Switch" and "Vibra Switch Delayed" (you can delete that one). Then in Settings>buttons> Select button 6, the top-left button currently used for single-press=Voice Speed Dial, press-and-hold=Recorder, re-assign the "press-n-hold button to be "Vibra Switch" and you are done.

I've been listing my tweak tries in amother thread, I can't get Bluetooth to redirect all sounds out to headset and I also can't get vjay lumos III to make the display go super bright. With no transreflective screen, this is now a very important tweak to me, I hope these can be figured out.

Use a little app called "BTaudio toggle" it works good for me!

[RemE]

Love you spiro! Searched and found BTaudio.exe, Life is good! With my 8525 I had to use Mortscripts, this is easier. Pressing my Jawbone headset button launches VoiceDialer and kills the re-direct, but that's no big deal. I like that I can now launch Voicedialer.

Last tweak remaining is a single button toggle to BRIGHTEN the screen!

[josue4231]

I installed Vibra Switch in my new Tilt but is working as described. Anyone knows why?

[paulsuerth]

i'm not sure about the commands to switch to vibe mode ( i use phone suite) but to expose the PTT button (short and long)
try adding a couple of new reg keys 40C6 and 40C7 in HKLM/software/microsoft/shell/keys. mimic the the keys and values on 40C5 and then soft reset.... it will then show up in the button control panel.

for reference, this is where i got it...
http://forum.xda-developers.com/showthread.php?p=1577293

[wrecks47]

i'm not sure about the commands to switch to vibe mode ( i use phone suite) but to expose the PTT button (short and long)
try adding a couple of new reg keys 40C6 and 40C7 in HKLM/software/microsoft/shell/keys. mimic the the keys and values on 40C5 and then soft reset.... it will then show up in the button control panel.

for reference, this is where i got it...
http://forum.xda-developers.com/showthread.php?p=1577293

Yes, I can confirm this works well. I've mapped a long press of my PTT button to Vibra Switch, so I just hold it down to toggle between ring and vibrate.

[Jim_R]

Last tweak remaining is a single button toggle to BRIGHTEN the screen!

I created a shortcut to the backlight application in /Windows/Programs and then mapped it to a button. A single push of that button brings up the backlight app, from there you can use the right directional button to increase brightness in steps. Biggest problem for me was adjusting brightness outside on a sunny day where the screen can not be seen - this fixes that for me.