HTC Kaiser Hard-SPL v1 - CID Unlock & Flash any ROM to your device (4 free)

[P1Tater]

sir, i just bought my kaiser from a friend what i found out that when i soft reset my kaiser there is a message above the htc logo "ui build for testing only!"
does xcpuscalar works in kaiser?
coz i installed xcpuscalar and everytime i use it kaiser always restart.....
still using original rom, not upgraded yet...

pls help

sounds like that is just your splash screen. use one of mine in the link below or search around and find one you like and flash it. Hope this helps.:)

[DragonStar]

Hi,
Trying to run this on my HTC Kaiser, both this version and the fix to the white screen. Everytime I replug in my USB cable it comes up with the "USB Device not recognized popup". If I try and continue, then after the screen where it says "Verifying the information on your PDA phone" it comes up with an error message. It says "Error [260]: Connection".

Does anyone have any suggestions for me?

Thanks,
DragonStar

EDIT: So now I can get it to get to the screen where it tries to update (ie. where the progress bar is with "updating the ROM image on your phone", however it seems to get stuck here at 0%. I can only get to this stage if I unplug and replug pretty much as soon as it says "USB" on the tricolour screen. This is frustrating me no end!

[matmaneyre]

Hi,

Has anyone managed to make a JumpSPL that works for SPL 1.82.000 yet? All the opther options so far don't work with this version. Seems O2 had the measure of all us XDA Stellar owners!

I've been following the forums for days & searching all over the place but I haven't found anything yet, so apologies if I've missed it. I'm still unable to flash my device & it's really starting to look like the end of the world.

I mean if you can't flash.....what's the meaning of life? :D

[pjbongco]

http://forum.xda-developers.com/showthread.php?t=335568[check the FAQs or stickies there is a whole thread for this] and yes you'd want to revert to ALL ORIGINAL [read: waht came on the device] before going for warranty.

Hello byncastro! I also see your name in pinoywindowsmobile. Just want to ask something. I already flashed the HTC rom on my AT&T Tilt so that it will have the video call option in the dialer. It was different when the tilt still had the at&t rom. I used the video call using my smart nokiae90 line and my tilt accepted the call. However, my tilt could not send video image and the screem in the nokiae90 says "Waiting for image" while the line is connected. Any idea how to fix this? Should i change the radio Rom (from current AT&T radio rom 1.27.12.11 to HTC radio?) or do some editing in the registry, etc...of my tilt? Please help. Thanks.


pjbongco
paulbongco@yahoo.com

[meihlani]

Just bought the AT&T tilt and SIm unlocked by following directions from thread. Would like to cid unlock, ATT program is slow! But as a beginner need detailed instructions as to where and how to download program, ie hardspl?, and how to unlock cid cause I tried and don't want to mess up the phine. Please Help!!:(

[pjbongco]

Just bought the AT&T tilt and SIm unlocked by following directions from thread. Would like to cid unlock, ATT program is slow! But as a beginner need detailed instructions as to where and how to download program, ie hardspl?, and how to unlock cid cause I tried and don't want to mess up the phine. Please Help!!:(

Please read this thread:

http://forum.xda-developers.com/showthread.php?t=334679

http://forum.xda-developers.com/showthread.php?t=334679&page=10

[ffffffff]

Hi,

Has anyone managed to make a JumpSPL that works for SPL 1.82.000 yet? All the opther options so far don't work with this version. Seems O2 had the measure of all us XDA Stellar owners!

I've been following the forums for days & searching all over the place but I haven't found anything yet, so apologies if I've missed it. I'm still unable to flash my device & it's really starting to look like the end of the world.

I mean if you can't flash.....what's the meaning of life? :D
Same here! I have followed the Harspl and then White screen. Then jumpspl, got to change the splash. When cook the rom, nealy bricked my phone. Had to use Mitty to rescue. Not only that, when I unplugged the usb, it went back to tricolor screen. Tried jump spl and load the O2 rom found on this site, manage to get it back to work. But got a strange combination here:

When switch on: it shows 1.27.12.32;22.45.88.0rh, and 1.56.00.00. But when find Bootloader; it shows; Kais30, Spl-1.82.0000, CPLD-8. It seems O2 managed to add some extra protections!!!!

It looks like, it dose not hardSpl, but I managed to splash using my kids photos(lovely) and also manage to unlock the phone as well. All nice, but I really want to use some of the wonderful roms I have seen here rather than O2's OEM staff.

Helpfully, some of Guru here won't give up and we aill get some updated software soon!

[GSLEON3]

Same here! I have followed the Harspl and then White screen. Then jumpspl, got to change the splash. When cook the rom, nealy bricked my phone. Had to use Mitty to rescue. Not only that, when I unplugged the usb, it went back to tricolor screen. Tried jump spl and load the O2 rom found on this site, manage to get it back to work. But got a strange combination here:

When switch on: it shows 1.27.12.32;22.45.88.0rh, and 1.56.00.00. But when find Bootloader; it shows; Kais30, Spl-1.82.0000, CPLD-8. It seems O2 managed to add some extra protections!!!!

It looks like, it dose not hardSpl, but I managed to splash using my kids photos(lovely) and also manage to unlock the phone as well. All nice, but I really want to use some of the wonderful roms I have seen here rather than O2's OEM staff.

Helpfully, some of Guru here won't give up and we aill get some updated software soon!

Listen, you're missing the most important step. PM me & I'll walk you thru it.

[ffffffff]

Listen, you're missing the most important step. PM me & I'll walk you thru it.

Well, thanks. Has Pmed you and I am waiting. Seems to me that timezone difference could work against us as I am at GMT time, what is yours?

[Griffy wiffy]

Hi,
Trying to run this on my HTC Kaiser, both this version and the fix to the white screen. Everytime I replug in my USB cable it comes up with the "USB Device not recognized popup". If I try and continue, then after the screen where it says "Verifying the information on your PDA phone" it comes up with an error message. It says "Error [260]: Connection".

Does anyone have any suggestions for me?

Thanks,
DragonStar

EDIT: So now I can get it to get to the screen where it tries to update (ie. where the progress bar is with "updating the ROM image on your phone", however it seems to get stuck here at 0%. I can only get to this stage if I unplug and replug pretty much as soon as it says "USB" on the tricolour screen. This is frustrating me no end!

PLEASE HELP I CANT GET FURTHER THAN THIS EITHER!!!! TRIED XP PRO, VISTA, NO JOY!!!

[drawde]

I'm coming from a HTC Wizard (Cingular 8125), and should be getting my Tilt within the next few days.. I've been lurking around the Kaiser section for a while, and just had a quick question..

I can use HardSPL regarless of what IPL/SPL my device has? And, there's no different versions of the Tilt, or is there? For example, with the Wizard, there were G3 and G4 models, and I needed to do a bunch of intermediate steps to get my IPL/SPL to what it needed to be to flash certain roms..

[DVS_WiNdz]

Question about this.. If I hard reset my Kaiser, would I have to use Hard-SPL again?

[framed]

Hi,

I apologize me for my bad English but I am really in the troubles.
I have purchased a ppc phone Kaiser 100 brands AT&T Tilt unblocked, and I have followed your good guide to put it the Italian ROM. To the first step the procedure XDA-Developers HTC Kaiser HardSPL CID Unlocker v1.0 has returned me the error 262.

The device when is put in BL it has this initials:
KAIS1*0
SPL-1.56.0000
CPLD-8

What can I do?

Thanks.

[juanwen]

hi... buddies... i had a problem here... i buy a tilt last week... . im trying to unlock the SIM

but.... the phone don't want to run kaiser-HardSPLv1, I conect to the PC the sinc turn green and when i run the SPLv1 the screem of the phone stay white... and frezze there...

what can i do/?

[kmlworld]

I got my Tilt phone and unlocked by AT&T but want to use different ROM but I got the connection error when I tried to run your HardSPL. Please help!

[qaiserjaved]

Hey Guys..

I have unlocked HTC Kaiser Locked to Orange UK two weeks ago but now i am having a problem. After doing HardSpl..i can see "SPL-1.0 OliPof" if i put my phone into bootloader mode. Now the problem is whenever i want to run KaiserCustomRUU, which is step 1 of sim unlocking the phone, i get the messege before actual installation starts..""Kaiser-simunlocker/step1/kaiser-radio-patched.nbh" i guess the last file is the file patched from the software. When i press ok, It give me a message of "ERROR[238]: FILE READ" "The update utility can not open the requested file. Please Check your Update Utility" I dont know what to do now. I have even took the battery off for like 5 times..restarted my phone so many times. and even tried to do flash_hardspl (One i have explained above) so many times. But i am unable to find the solution. Please help me in this regard.

I know there are some geniuses monitoring this forum. Please help me guide me with the detailed procedure.

Thanks for the previous help.

[xmoo]

I'm getting white screen while trying to HardSPL a device of my friend.


ROM version: 1.56.404.6
Radio version: 1.27.12.32
Protocool Version: 22.45.88.07H

[ilciano]

All,
I'm made a big mistake, :confused: cannot remember if some times ago I've already Hard SPL my Kaiser, I cand do it again or there is a way to understand if my Kaiser is already Hard SPL ??

Thanks

[jorfee]

all Im getting is a white screen and nothing else when I run hard spl...whats goin on?

[qaiserjaved]

Hey Guys,

I have solved the problem of HardSpL. Thts done but now when i run KaiserCustomRUU from step 1 folder, for unlocking, it pops a message "Desktop\kaiser-unlocker\step1\kaiser-radio-patched.nbh" and after when i press ok, it gives an "ERROR 238: FILE READ. The update Utility can not open the requested file. Please check your update utility".

Please some body help me. I really dont understand why i am getting this error as i have successfully done the HardSPL.

Thanks

[Biglittlewhateva]

all Im getting is a white screen and nothing else when I run hard spl...whats goin on?

Me too. :(

[XiDe]

I am too stuck in the Tri color screen with KAIS130 SPL-1.81.0000 CPLD-8 USB bootloader screen, in the top right hand side of the screen it has RUUNBH. Cannot get Active Sync to work or recognise Kaiser Tytn 2.

Can any one help Please

[xmoo]

I am too stuck in the Tri color screen with KAIS130 SPL-1.81.0000 CPLD-8 USB bootloader screen, in the top right hand side of the screen it has RUUNBH. Cannot get Active Sync to work or recognise Kaiser Tytn 2.

Can any one help Please

You stuck in bootloader.

[XiDe]

yes, an help please

[xmoo]

yes, an help please

Use the search, i don't know how you could fix it anymore. Just search something like "stuck in bootloader".

[The-Trigger]

Hello,

i've installed HardSPL to remove the Sim-Lock from my device (German T-Mobile MDA vario III). After i've unlocked succesfully, i now want to remove HardSPL from my device. I couldn't find something how to do this.

Can you please help me.

Thanks.

Trigger

[idunnojack]

SOrry if this question has been answered before, but I have looked everywhere on this site and nothing has turned up. I recently bought a locked AT&T tilt and i want to use it on t-mobile. Of course after I ran through setup, it went straight to the password screen asking for the unlock code. I use windows Vista and when i connect it to the computer it tells me I have to unlock the phone before windows mobile connect works("to connect or synchronize to this PC, please authenticate on your device"). Now is there a way for me to install hardSPL (which would then allow me to run the sim unlock) or just sim unlock it (besides paying for it) from here? i would really appreciate your help!

[oaldawe]

Quote:
Originally Posted by jorfee
all Im getting is a white screen and nothing else when I run hard spl...whats goin on?

Me too.

me too please help us

[RMarx]

Hi pof,
I want to make an update for my MDAIII.
I know your 3-Steps-Way.
1 Step - OK
Active Sync (version 4.5) finds an "HTC80" and connect successfully.
2 Step - ???
Echo:
=== Kaiser SIM ...
=== Donations ...
\\.\WCEUSBSH001: No such file or directory
cannot connect to \\.\WCEUSBSH001

What is to do?

[hdoan444]

I tried your HardSPL v1 and failed at the very first step when running SSPL-KAIS.exe from my phone. All I got is a white screen and it stays that way until I hit reset on my phone.

Please help to go beyond this step. Thanks!

tri-color screen says:
KAIS1*0
SPL-1.93.0000
CPLD-8

found this thread in sticky http://forum.xda-developers.com/showthread.php?t=354061. look like it'll fix the problem. I'm trying it out if I come back then it doesn't work. Thanks and good luck to those with same problem as mine... (http://forum.xda-developers.com/showthread.php?t=354061)

[ffffffff]

I tried your HardSPL v1 and failed at the very first step when running SSPL-KAIS.exe from my phone. All I got is a white screen and it stays that way until I hit reset on my phone.

Please help to go beyond this step. Thanks!

tri-color screen says:
KAIS1*0
SPL-1.93.0000
CPLD-8

found this thread in sticky http://forum.xda-developers.com/showthread.php?t=354061. look like it'll fix the problem. I'm trying it out if I come back then it doesn't work. Thanks and good luck to those with same problem as mine... (http://forum.xda-developers.com/showthread.php?t=354061)

How about http://forum.xda-developers.com/showthread.php?t=369567

Good Luck

[Squeaky369]

So I have some questions after reading 54 pages of replies to this. And I've searched and read the WIKI and just can't find these answers...

I'm using a ATT Tilt; all official roms and crap.

1) Does running the Hard-SPL erase the memory on the device? (Contacts, files, programs, etc...)

2) Can you brick the phone running the Hard-SPL program?

3) Do you need to have a cooked ROM ready for when the SPL is finished? I watched that dudes YouTube video walk through; and I couldn't tell what he was doing. It looked like he ran a cooked ROM; but I couldn't tell...

4) If you don't have to have a cooked ROM after it's finished, will the phone boot back into the ROM that's already installed on the phone? I couldn't tell from that dudes video; again, no idea what he was doing.

Thank You.

[fbrooks2000]

Can somebody show me some images of this ROM? I would like to see what I am getting before I flash this ROM. I just paid a buttload of money for this phone I don't want to crash it. I really appreciate anyones help here.

[DragonStar]

PLEASE HELP I CANT GET FURTHER THAN THIS EITHER!!!! TRIED XP PRO, VISTA, NO JOY!!!

Ok, what I finally had to do was as soon as the screen displays USB (on the PDA), and I mean as soon as it says it, not a few seconds after, quickly pull the cord out and put it in again. Do this as quick as you can. This is what worked for me. Since then, I've gotten HardSPL installed and upgraded to Dutty's ROM and upgraded my radio.

[illmicill]

i tried to do this and when i pressed ok on my phone to run the file it said it may mess up my device. i said ok anyway and suddenly my screen went white, froze my internet explorer and the hard spl window. now my phone wont even turn on and i can't even hard reset. i just got the phone today lol. any way to fix this? otherwise im just gonna return it tomorrow and get a new one.

[afw420]

Every time I try to flash hardspl everything seems like it is going to work and then I get a message that says "Error: Connection. Please make sure you PDA is connected to the USB. Why does it keep doing this if all of the connections are correct??? I tried it on 2 different pc's with the same result. Thank you:confused:

[_RMB_]

Every time I try to flash hardspl everything seems like it is going to work and then I get a message that says "Error: Connection. Please make sure you PDA is connected to the USB. Why does it keep doing this if all of the connections are correct??? I tried it on 2 different pc's with the same result. Thank you:confused:

what OS are you using?

[_RMB_]

if your using vista try this....should work after......

http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27

[afw420]

although it took several hours of trying the same thing over and over...it finally went through, and with many minor tweaks I am not exactly sure what it was...but thank you all for your help and concern, and I pledge to bring back to this site when I make my millions... you all are amazing

[P1Tater]

although it took several hours of trying the same thing over and over...it finally went through, and with many minor tweaks I am not exactly sure what it was...but thank you all for your help and concern, and I pledge to bring back to this site when I make my millions... you all are amazing

Dont forget me, when you make millions. I only ask for a bucket of $50's. That's all.:D

[P1Tater]

So I have some questions after reading 54 pages of replies to this. And I've searched and read the WIKI and just can't find these answers...

I'm using a ATT Tilt; all official roms and crap.

1) Does running the Hard-SPL erase the memory on the device? (Contacts, files, programs, etc...)

2) Can you brick the phone running the Hard-SPL program?

3) Do you need to have a cooked ROM ready for when the SPL is finished? I watched that dudes YouTube video walk through; and I couldn't tell what he was doing. It looked like he ran a cooked ROM; but I couldn't tell...

4) If you don't have to have a cooked ROM after it's finished, will the phone boot back into the ROM that's already installed on the phone? I couldn't tell from that dudes video; again, no idea what he was doing.

Thank You.

1. no
2. possible, but pretty hard to do.
3. no. you are doing this so you can flash a cooked rom.
4. yes.

[terpr13]

I just bought my ATT Tilt and i cant get this to work. it goes to a white screen....then a few minutes later activesync disconnects....but nothing else happens...i waited ten minutes and never got anymore instructions or anything...can someone help? :confused:

[Mammouth]

I received my AT&T tilt locked.

After i ran HARD-SPL to unlock it.
May i directly update with Dutty Rom 6.1 using Kaiser_RUU.exe ?

[jwolffr]

You are a STAR - evrything went just as stated. I have a NEW PHONE!!!!! Certainly worth the paypal donation

[JacksLostSanity]

I just bought my ATT Tilt and i cant get this to work. it goes to a white screen....then a few minutes later activesync disconnects....but nothing else happens...i waited ten minutes and never got anymore instructions or anything...can someone help? :confused:

Im getting exactly the same problem! :(

[Gibbs]

Did you read this thread?

http://forum.xda-developers.com/showthread.php?t=354061

[Knumb]

I just ran the Hardspl app and it auto booted my phone and the AT&T crap still came up. Was I supposed to add the new rom in same folder? I just want to verify that hardspl was installed. How can this be done? Everything went well with the process...TIA

[P1Tater]

I just ran the Hardspl app and it auto booted my phone and the AT&T crap still came up. Was I supposed to add the new rom in same folder? I just want to verify that hardspl was installed. How can this be done? Everything went well with the process...TIA

put it in bootloader mode
camer+power+soft reset.
hold till you get the 3 color screen.
what does it say there.

[Knumb]

sorry P1Tater...I found out and it was good to go....Flashed it already and I like it!

[kuzco1]

Hi,
last week I got my new VPA Compact V with the following ROM:
ROM-Version: 1.56.162.5
ROM-Datum: 09/04/07
Funkempfaenger: 1.27.12.11
Protokoll-Version: 22.45.88.07H

I am trying to install the orginal HTC-ROM KaiserHTC_GER_1.56.407.3Reconstructed, but I have no success.

I have read a lot of mail and so on, but I does not work.

kaiser-HardSPL.exe does not work, I have the "white screen problem" - so that I have tried JumpSPL1.56-KAIS which brings me in the tri-color-screen. I disconnect and reconnect the USB cable, but if I start KaiserCustomRUU.exe - it sasys that active sync has to be active, this is not the case.

Please help.

I have also tried to install TomTom6, but I get always the info the TT6 is not working on this PPC. Perhaps the Vodafone-ROM is the reason.

Please help

thanks
kuzco1

[PaNa-S]

I accidentally attempted to HardSPL my Kaiser using the Hermes HardSPL program ("Hard-SPL-V7") -- it failed, and the device seems ok, but do I have anything to worry about? I can easily exchange this for a different one, would this be worth it for peace of mind? Any guidance would be appreciated. Thanks!

[faruqsavar]

Hello
any one can help me how recover my phone

its coming on recovery mode

with red green blue whit

KAIS130
SPL-1.810000
CPLD-8

ANY WAY TO recover
thank you

[pyramids]

When i RUN kaiser-HardSPL.exe on Computer (PC)....it asks if i want it to run onmy phone. i say yes and all and thn the screen goes blank(white). can anybody plz tell me why this is happenign????
thx


After flashing HardSPL you'll be able to flash any Kaiser ROM to your device!

This tool will allow you to change the ROM language, flash cooked ROMs, custom splash screens, etc...


FEATURES


SuperCID / Security Level=0
Does not check NBH signatures
Based on 1.50 MFG bootloader, rtask enabled
Accept any password
Model ID check only 4 chars
SPL overwrite DISABLED (to bypass, use SSPL-KAIS.exe (http://forum.xda-developers.com/showthread.php?t=334678))


INSTRUCTIONS


Connect Kaiser to computer using USB cable
Make sure ActiveSync icon is GREEN
RUN kaiser-HardSPL.exe on Computer (PC)
Follow instructions on screen:


************************************************** ***************************
XDA-Developers HTC KAISER CID Unlocker by pof
HTC TyTN II P4550 / T-Mobile MDA Vario III / AT&T Tilt (8900, 8915, 8925)
Swisscom XPA 1605 / Vodafone v1615 / Vodafone VPA Compact V / SFR v1615

Features:
1. SuperCID / Security Level=0 2. Does not check NBH signatures
3. Model ID check only 4 bytes 4. Based on MFG bootloader, rtask enabled
5. Accept any password 6. SPL overwrite disabled

This software is free to use but at your own risk, I take no responsiblity
for any conflict, fault, or damage caused by this unlocking procedure.
No warranties of any kind are given, any commercial use is prohibited.

Your donation is a strong incentive to continue research on new devices,
if you find my work useful please cosider making a PayPal donation to:
pau@eslack.org
Any donation amount is greatly appreciated :-)

************************************************** ***************************

Please make sure ActiveSync is enabled (GREEN icon in systray)
and hit ENTER to start...

Kaiser JumpSPL is running on your device, please check your device
screen and follow the steps until you see the tri-color screen.
When done hit ENTER to continue...

Device screen should be now TRI-COLOR and show "USB"
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
ActiveSync icon should become gray after that.
When done hit ENTER to continue...

Phone screen should now be tri-color and the activesync icon gray
if not, the loading process has failed and you'll have to repeat it again.

If all was OK hit ENTER and the standard "PDA Phone ROM Update Utility"
window will start, allowing you to flash HardSPL on your device.

Hit CTRL+C to Cancel or ENTER to continue...

Follow the steps on the wizard to flash HardSPL, when finished your
device will reboot. It should last no more than 1 minute.
- Launching RUU, please wait...

Process is finished, congratulations!
If you find it useful don't forget to donate :)
************************************************** ***************************
(c)2007 pof - XDA Developers

Hit ENTER to quit.



THANKS TO:
- Esteve, Olipro, arc, pancake, HaRET developers, and everyone else who I forget... :rolleyes: without your help this wouldn't have been possible!


DISCLAIMER

This software is free to use but at your own risk, I take no responsiblity for any conflict, fault, or damage caused by this unlocking procedure.
No warranties of any kind are given, any commercial use is prohibited.


DONATIONS
https://www.paypal.com/en_US/i/btn/x-click-but04.gif (https://www.paypal.com/cgi-bin/webscr?cmd=_xclick&business=pau%40eslack%2eorg&item_name=xda%2ddevelopers%20donation&no_shipping=1&cn=Comments&tax=0&currency_code=EUR&bn=PP%2dDonationsBF&charset=UTF%2d8)

Your donations are a strong incentive to continue research on new devices, if you find JumpSPL useful please cosider making a PayPal donation. Any donation amount is greatly appreciated :)

Enjoy! ;)

[GSLEON3]

If you PM me or find me on MSN messenger (gsleon3@hotmail.com) I'll help walk you thru it.

[sanroman]

I got the same error. Please submit the solution. almost 10 hours trying to unlock the TytnII 1615. help please!:)

[renolison]

does this program work on windows vista?

[nondutch]

Hello Guys,

I have been trying to unlock my phone and upgrade to another version since my T-Mobile NL phone has a very odd problem.
When i have the headset connected (listening to music mostly) and i receive a call, the sounds just goes 'poof' and there is no bringing it back without a soft reset...
(a BIG search here and in google just didn't seem to bring any similar errors, i wanted to update the software back then, but went for repair, as it was a new phone)

Funny enough it came back from 'repairs' today with 'something' (they couldn't explain what) replaced... guessed right, same problem!

so i'm gonna guess this is a software probelm and in any case i prefer to have an english version with all the advantages you guys bring for us...

Now, for the thread in here, i am trying to run this tool in Windows Vista ultimate 32.
Have changed my active sync to the HTC as pointed in another thread, have tried to run the kaiser sim unlocker, but everything appears to fail....
with the HardPSL i get these error messages

**************
Please make sure ActiveSync is enabled (GREEN icon in systray)
and hit ENTER to start...
'pput.exe' is not recognized as an internal or external command,
operable program or batch file.
'prun.exe' is not recognized as an internal or external command,
operable program or batch file.

Kaiser JumpSPL is running on your device, please check your device
screen and follow the steps until you see the tri-color screen.
When done hit ENTER to continue...
Device screen should be now TRI-COLOR and show "USB"
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
ActiveSync icon should become gray after that.
When done hit ENTER to continue...
Phone screen should now be tri-color and the activesync icon gray
*****************

Yeah, after that there is nothing further...
I have attempted to run the program as an administrator, have also changed it to run in XP SP2 compatibility mode, and have tried by copying it directly on to my C: drive... none of the combinations seems to get beyond this point and i receive exactly the same errors...

I am just stuck in this step and am unable to find anything on the thread that points me in a better direction...

I have been reading through several threads and several tools, like the JumpSPL1.56-KAIS (which doesn't do much as my phone remains in bootloader mode just about all the time, and the active sync icon in green)(Seriously looking forward to the see no evil ROM) but


your help will be greatly appreciated!

Edit: I received the phone back from T-Mobile, twice was sent to their 'repair' center and came back with the same problem.
Turns out that i finally managed to upgrade the OS and the Radio, finally with the Radio upgrade the probelm was fixed.
The Radio Version was 1.27.12.32 and now i'm using 1.64.08.21

The installation problem was because of Vista, but with VMWare and XP2 on the same machine everything works.
apparently the files that should be extracted when running any of these programs are NOT, so the files were never found and the installations never even got started.

Hope tis is helpful for the Devs.

Cheers!

[franknj]

hello everyone,
i am using windows vista on my laptop and i have tried all day to try and do this and it just does not work at all.

I have recieved errors all day and still i have yet to CID unlock my AT&T Tilt. Any help would be great in trying to get this done with out bricking my device. thank you so much.

I have tried everything and don't know what is going on with this. I do not have any other computers that have windows xp on it all i have is a macbook pro laptop and the laptop that is running windows vista.

I really would like to get some good ROMS on my Tilt i am so bored with the ROM it has on it now lol.

[nondutch]

(attempting to delete)

[joshmoulton]

I've as well tried updating to Dutty's ROM and it always fails and says recovery mode. When I try running the HardSPL it sits at a white screen and never makes it to the tri-color. What am I doing wrong? joshmoul10@hotmail.com is my msn if anyone has any suggestions. I appreciate it. I have HTC Tilt.

[LTxda]

I've as well tried updating to Dutty's ROM and it always fails and says recovery mode. When I try running the HardSPL it sits at a white screen and never makes it to the tri-color. What am I doing wrong? joshmoul10@hotmail.com is my msn if anyone has any suggestions. I appreciate it. I have HTC Tilt.

Try this:

- Take out any SD cards
- Hard reset the device
- Activesync it
- HardSPL (if you already haven't. you can confirm it by going into Bootloader screen)
- As long as new SPL is on the device you should be able to go with a new ROM flash.
- As always, hard reset the device immediately after flashing with new ROM

Hope this helps.

[joshmoulton]

Well I had updated to the new HTC ROM last week and had no problems. I removed SD card and did the 'clear storage' option. After that is when I connect it to ActiveSync and it connects. When trying to do the Kaiser HardSPLv1 and when the command prompt I follow instructions, it says wait for tri-color screen but it just sits at a white screen. Then I just have to remove battery and start back over. Any ideas?

[joshmoulton]

Anybody have any ideas? I've tried to update the ROM with Dutty's newest one, but it always ends up in recovery mode..

[franknj]

i am having the same issue also. it is not working for me either i am having alot of issues with getting this to work.
I followed all the directions carefully and still the samething is happening.
Any help would be great thanks so much.

[typea61]

I am also not having any luck with the Hard-SPL. I have tried this multiple times including doing hard resets before I start Hard-SPL. I have a good ActiveSync connection (green icon) and then start kaiser-HardSPL.exe. I hit enter then get a message on the Tilt that says the program is from an unknown publisher, etc. Do you want to continue...blah, blah, blah...and I click Yes. This brings up the KAISER JumpSPL v1.0 screen and I click continue and it goes right to a gray screen and stays there forever. I have to do a soft reset (stylus to the little hole) to recover. I have no SD card installed.

Any help would be appreciated.

EDIT: just found this thread which I will try...http://forum.xda-developers.com/showthread.php?t=354061

EDIT #2: Why do I always look like a total nub in the first posts of every forum I join? I know to search and read everything before posting but for some reason I always make a stupid first post, like this one. Of course this gray screen problem has been solved, long ago, if I had just searched the right places...http://forum.xda-developers.com/showthread.php?t=354061 That solution worked great for me. Now, to try some WM6.1 since I have nothing better to do tonight. Gracias.

[bluelook]

After an hour and a half of reading all the 57 pages and zillion times of hard spl install all over again , i finally understood what caused this error.
The usb connection while in a boot loader stage needs to be re-established. my problem was the little screen that pop uped behind the Firefox with the forum and i haven't noticed, that i need to tell the OS that the usb blah blah smth is trusted. once i did it everything worked! i got the message that new hardware is succesfully installed. the hard spl worked perfect and the new ROM afterwards too.
i think this issue should be added to wiki or at least to the first page of this thread. i saw it many times during my reading, believe me this is not so easy to go over aaaaaaallll the pages.

good luck to everyone :)

[Bluediss]

I tried it also to flash to another rom. But at 16% it stops and i dont now why but i cant repair the rom. When i reboot the kaiser phone he comes directly in bootloader mode.
The do nothing anymore, i tried to flash from sd or mtty. Nothing works.
By mtty, i get the error that the command boot is a false command.
So i think my phone is really fuckt up. :-( this is really the firt time in 3 years my phone stops and i cant find solutions on XDA.

I can found only this tread with :

For those of you had the phone stuck in bootloader mode after flash with SSPL stopping at 16%, follow these instructions to unbrick your phone:

1. Download mtty.exe
2. Disable activesync (connection settings -> uncheck "allow usb connections")
3. Connect your Kaiser to PC using USB cable.
4. Open mtty, select USB port and click OK.
5. Hit ENTER twice, you should see the "Cmd>" prompt.
6. Type the command "boot", you should see something like this:

Code:
Cmd> boot
InitDisplay: Display_Chip=1
No card inserted
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++After that device should boot WM6 again, you can now re-enable USB connections in activesync and flash HardSPL

But it won't work.
I hope somebody can help me a litlle.
Greeting Thetmar.

[haxk847]

Trying to run KaiserHardSPL v1 to my new ATT Tilt. Tried it both on XP and VISTA several times with the same result. When it comes to the PC's dos screen showing "Kaiser JumpSPL is running on your device..." phase, I see the device's screen blank out with white background color instead of switching to the tricolor boot screen and see the active sync disconnect and the screen remains this way until I do some things like power off followed by soft reset to bring it back to working state. :confused:

[haxk847]

Trying to run KaiserHardSPL v1 to my new ATT Tilt. Tried it both on XP and VISTA several times with the same result. When it comes to the PC's dos screen showing "Kaiser JumpSPL is running on your device..." phase, I see the device's screen blank out with white background color instead of switching to the tricolor boot screen and see the active sync disconnect and the screen remains this way until I do some things like power off followed by soft reset to bring it back to working state. :confused:

edit 1: Sorry, should've looked further before posting. Will try the solution by jockyw2001 http://forum.xda-developers.com/showthread.php?t=354061 :)

[mccune]

I've did the Hard-SPL on my Vario III as well. It all seems to work fine. But after a few days I get the following message:

"The device is unable to boot because either you have turned off the device incorrectly or tried to install an application from untrusted source. Press END to reset your device or press any other button to cancel. This operation will delete all your personal data and restore the device to its factory default settings."

I've created a different thread about this problem but it seems there are not to many with the same problem.

Is it possible that this error has something to do with the Hard SPL?
I've tried Sleuth's 3.0 WM6.1 ROM and XDA Live v1.5 WM6.0 ROM. They both give me the message at some time. I'm able to boot after this message. Sometimes though it shows the start screen you see when you hard reset your device.

I've installed many applications so it might be also because of one of the applications? As we speak I'm trying to use a clean ROM to see if I can reproduce the error.

Link to the thread I've created HERE (http://forum.xda-developers.com/showthread.php?t=377981).

[intrygue83]

whad up guys. i have an att tilt. i got my sim unlock code from att and i unlock my phone. now i'm trying to the sim unlock. i have read the forums and do everything it says. when i goes from the tri color screen to the gray screen i see a progress bar with 0% at the end. it never goes up and 2 mins later it say communications error. i have re booted and everything. when i do a hard reset do i have to re-sim unlock my phone to get this cd unlock to work?
please help me!!!!!
Intrygue

[intrygue83]

I forgot to mention that i actually have to put my phone in bootloader mode myself. it goes to a white screen and stays that way. so i would have to take my battery out and take it to the bootloader myself then run the HardSPLv1. please help

[alidagr8]

Hi Pof

I have at&t tilt 8925 unlocked. I went to htc america site and updated rom and now i have 1.62.502.0; radio version is 1.27.14.09 and protocol version 22.45.88.07H
A friend of mine got the same unit from california and has front screen like htc touch and lots of other features ......
so i was planning to try downloading some more roms and downloaded the extreme and lite version of roms but it says make sure you do SPL first ... so i download hardspl v1 but my screen goes white, so i read another thread that says download the 5 attached files and try
jumpspl 1.56 or 1.93 etc. but those files don't work on my pc says its not valid32.exe file etc.
please help me on this, considering i'm a rookie and need some spoon feeding here so that i can upgrade my phone without damaging it and can install great stuff.
Really appreciate your help on this.
Thanks
:cool:

[XtreMe_G]

I forgot to mention that i actually have to put my phone in bootloader mode myself. it goes to a white screen and stays that way. so i would have to take my battery out and take it to the bootloader myself then run the HardSPLv1. please help

its because of your idiocy putting the device in bootloader mood yourself that its not working. and if you had actually taken the time to search, or look at the sticky, or even look at the wiki you would have found this:

HardSPL will not install - WHITE SCREEN: SOLVED (UPDATE 01. March 2008) (http://forum.xda-developers.com/showthread.php?t=354061)

[XtreMe_G]

Hi Pof

I have at&t tilt 8925 unlocked. I went to htc america site and updated rom and now i have 1.62.502.0; radio version is 1.27.14.09 and protocol version 22.45.88.07H
A friend of mine got the same unit from california and has front screen like htc touch and lots of other features ......
so i was planning to try downloading some more roms and downloaded the extreme and lite version of roms but it says make sure you do SPL first ... so i download hardspl v1 but my screen goes white, so i read another thread that says download the 5 attached files and try
jumpspl 1.56 or 1.93 etc. but those files don't work on my pc says its not valid32.exe file etc.
please help me on this, considering i'm a rookie and need some spoon feeding here so that i can upgrade my phone without damaging it and can install great stuff.
Really appreciate your help on this.
Thanks
:cool:

that's because you are suppose to run those files from your phone

[alidagr8]

that's because you are suppose to run those files from your phone


Well i'm acting like a real rookie here, but hey, i guess i'll learn .. bare with me .. so if i take the sim card and sd cards out, how can i run the files from the phone, cuz it says no sim card, emergency calls only...
so i tried hardspl but again white screen ....
i'm lost here ...... can i not just install that rom XTRM_1.0-6.1X_WWE_TILT straight without hardspl ?
i'm sorry folks if i am acting like a goof, but i really hope atleast one fellow will help me step by step and i appreciate your time.
thanks a lot
regards
:confused:

[intrygue83]

Well i'm acting like a real rookie here, but hey, i guess i'll learn .. bare with me .. so if i take the sim card and sd cards out, how can i run the files from the phone, cuz it says no sim card, emergency calls only...
so i tried hardspl but again white screen ....
i'm lost here ...... can i not just install that rom XTRM_1.0-6.1X_WWE_TILT straight without hardspl ?
i'm sorry folks if i am acting like a goof, but i really hope atleast one fellow will help me step by step and i appreciate your time.
thanks a lot
regards
:confused:

you put it in your documents on your phone from your computer. start>my computer>windows mobile device>windows mobile device>my documents
2 posts up click the bottom link on XtreMe_G post. it helped me and mines working fine

[XtreMe_G]

Well i'm acting like a real rookie here, but hey, i guess i'll learn .. bare with me .. so if i take the sim card and sd cards out, how can i run the files from the phone, cuz it says no sim card, emergency calls only...
so i tried hardspl but again white screen ....
i'm lost here ...... can i not just install that rom XTRM_1.0-6.1X_WWE_TILT straight without hardspl ?
i'm sorry folks if i am acting like a goof, but i really hope atleast one fellow will help me step by step and i appreciate your time.
thanks a lot
regards
:confused:

yes sure you can install whatever rom you want without hardspl, but before you do, just do a search for bricked and see how many dumb fucks bricked their phones because they did not install hardspl. why the hell do you think we keep telling everyone to install hardspl first? you think its just some big prank which senior members a pulling off just so we can have a laugh at all the noobies doing an unnecessary step? honestly, pls do some more reading before jumping in and flashing your device. it is after all a $700 device (if you dont consider all the operator discounts)

as for your issue, press the end call button or the and tada! you are back at you today screen.....and surprisingly everything else in the phone still works.

now, if at this step you still do not know what to do, ie if you dont even know how to execute a program.......then i suggest you go some reading, the manual, the wiki, or perhaps a pocket pc for beginners website......before you turn your phone into a brick. its either that or go get an iphone.

[jgottlieb]

Been waiting to do this for when I had time. I read about the white screen problem, the need to unplug and replug the USB cable.

I even watched the video a couple times.

Worked like a charm. :)

Looking forward to something better than the stock AT&T rom. :)

[rotteneggz]

Hi all,
My first post. I love the forums, helped me alot with my new ATT tilt i got for my birthday. I followed the instructions and got through it all perfectly fine. When the device restarts everything is the same though, nothing has changed. My question is: Is there a way to verify if i installed it properly? I read you need to hold the camera+power and do a soft reset. Ive tried that and all it does is restart the device. Am i doing something wrong? i just want to make sure i flashed it properly before i load a new rom.
Thanks

[josiahmgillespie]

ok so mine wont go past a white screen.....

[XtreMe_G]

@rotteneggz
press and hold the camera button, and reset, keep holding the camera button, it should bring up a tricolor screen. if it says something with olipof, then you're good to go

@josiahmgillespie
the solution to your problem is discussed in the thread, in the wiki, in the sticky at the top of this forum.

http://forum.xda-developers.com/showthread.php?t=354061

[wewex]

what is the Hard-SPL for? what does it do for my tilt phone?

[ap50]

It unlocks the ability to re-flash the phone with a new operating system ROM

[wewex]

all i want is to change is the radio from my phone,if i install this Hard-SPL what do i need to do next?:confused:

[wewex]

It unlocks the ability to re-flash the phone with a new operating system ROM

so do i need this if i want to change the radio on my tilt phone?

[nondutch]

so do i need this if i want to change the radio on my tilt phone?
Yes, you need to use it to be able to flash the Radio ROM to your device.

[Pisca]

I Have a Qtek 9100 as follows:

IPL 1.01
Spl 1.06
OS 1.1.75
Radio 01.01.10
ROM 1.1.75 - 09/22/05

I assume that SIm is unlocked since I can use any card from any operator

Question; Can I use this Hard SPL and after that upload any ROm that I choose ?

Sorry for the basic question, thanks in advance

[nondutch]

I Have a Qtek 9100 as follows:

IPL 1.01
Spl 1.06
OS 1.1.75
Radio 01.01.10
ROM 1.1.75 - 09/22/05

I assume that SIm is unlocked since I can use any card from any operator

Question; Can I use this Hard SPL and after that upload any ROm that I choose ?

Sorry for the basic question, thanks in advance
Pisca:
your device is a Wizard, this is the wrong place for questions about it.
This is what you're looking for:
http://forum.xda-developers.com/forumdisplay.php?f=248

Alternatively, you can start to take a look at threads like this one:
"The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards " on
http://forum.xda-developers.com/showthread.php?t=285435

ND

[hidavi]

So after I do this, I can install the L26 WM6.1 ROM?

[tigron]

Will using HardSPL erase all data ? or can I backup afterwards?

[wewex]

So after i install Hard-SPL on my tilt,And i also got the radio file i want how do i install the radio file to my tilt phone. Because i already did this but no luck? i think it's the rar file:confused:

[XtreMe_G]

Will using HardSPL erase all data ? or can I backup afterwards?

hardspl wont erase any data, but just do a backup beforehand, just in case

[XtreMe_G]

So after i install Hard-SPL on my tilt,And i also got the radio file i want how do i install the radio file to my tilt phone. Because i already did this but no luck? i think it's the rar file:confused:

it would help if you give us some more info like what errors did you get or what happened. help us help you

[Squeaky369]

1. no
2. possible, but pretty hard to do.
3. no. you are doing this so you can flash a cooked rom.
4. yes.

Awesome; worked; installed. Thanks!

[Baronic]

Help!!! MY hardspl flashing is not moving at 18% i dare not unplug or do anything! its been 5 minutes and its supposed to take a minute onli? PLSSSS HELP!


EDIT: communication error, i followed the recovery steps, and from there tried to continue. But then it said ready to continue update, but then cant connect! I'm stuck at tricolour with the word USB at the bottom. MDA Vario3 here. PLEASE HELP ME

[VooDoo1]

This is going to sound like a stupid question...but I need to know before I do this is toast my new phone.

In the instructions...this part where it says:

"Device screen should be now TRI-COLOR and show "USB"
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <==="

Now...do I ACTUALLY UNPLUG the cable from the phone 3 times and plug it back in 3 times?? Or is this what its just supposed to say and I do nothing but leave it plugged in?

[chowdary]

Well I Cant Get This To Flash On An Htc (kais130)
I Have Done One Hanset But It Is Not Working On The Other
After Running The Exe, Following On The Phone Display, When I Press Continue, It Doesn't Go Into 3 Colour Screen, It Only Shows White Lcd,
On This Stage I Have Put Manualy Into Three Colour Screen Couple Of Times. It Launches The Rom Update Exe But It Doesn't Go Further Than 0%
Any Sugesstions Please
Br

[superpdaguru]

cant make hard spl I only get white screen at th strat why is that?

[chowdary]

cant make hard spl I only get white screen at th strat why is that?

hello
found the solution in the forum
here is the link to the thread
http://forum.xda-developers.com/showthread.php?t=354061&highlight=spl-1.81.0000
br

[hudeck]

gents i`ve got a couple of questions,

i`ve tried to use hard-spl and came to the tri-colour screen.

To here

Device screen should be now TRI-COLOR and show "USB"
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
ActiveSync icon should become gray after that.
When done hit ENTER to continue...

Phone screen should now be tri-color and the activesync icon gray

then PDA Phone ROM Update Utility appeared and i couldn`t connect any more with the tynt 2.

what went wrong. please help because i feel that there went something wrong.
because after that i couldn`t connect to the computer any more.

thx.

[paul_flores]

My attempts to upgrade my v1615 (kaiser), I left on the screen to the 3 colors, and I can not update it gives me and operator error, but I can not put kaiser-HardSPL.exe I can help..

sorry for my english

TNKXX

[leon sprouse]

Cant update with this. Get white screen. tried work around. Got to part that said remove sim and sd. All I get then is screen saying sim missing and phone keypad to dial 911. Tried for hours to get this hardslp to work finally gave up. Any ideas? I have Vista with Mobile Divice Center not Active Synk. Does this matter?

[XtreMe_G]

My attempts to upgrade my v1615 (kaiser), I left on the screen to the 3 colors, and I can not update it gives me and operator error, but I can not put kaiser-HardSPL.exe I can help..

sorry for my english

TNKXX

is there another nbh file in that directory? move that nbh file somewhere else or move kaiser-HardSPL.exe to an empty directory

Cant update with this. Get white screen. tried work around. Got to part that said remove sim and sd. All I get then is screen saying sim missing and phone keypad to dial 911. Tried for hours to get this hardslp to work finally gave up. Any ideas? I have Vista with Mobile Divice Center not Active Synk. Does this matter?

yes, that call screen is a real "problem" for ppl who take out their sim card. most ppl solve it by pressing the end call button. however i have heard of some ppl solving this problem by pressing the OK, button, or even pressing the x button at the top right. btw you should post this in the "white screen" thread, so as not to confuse other ppl

[wewex]

if i have Hard-SPL on my tilt, can i install the new HTC ROM update (version 1.62.502.0) on my tilt phone without removing all my tweaks and programs?

[XtreMe_G]

if i have Hard-SPL on my tilt, can i install the new HTC ROM update (version 1.62.502.0) on my tilt phone without removing all my tweaks and programs?

no........

[flippolino]

I did use the Hard-SPL and after that I could flash the rom I would. So far so good! But When I put this MDA III (HTC TyTN II) on I still see this screen from T-Mobile for a while. Is there a possibility to get rid of this without throwing it away? I think of a firmware, but I don't see there is one. Ican't get it .HTC tells me to go to T-mobile and they tell me Idon't have a t-mobile phonenumber. Do I have to search for another firmware and if so where can I find it? Please your help! By the way :I bought this phone legally and second hand and want to bring it back in originally HTC shape.

[XtreMe_G]

I did use the Hard-SPL and after that I could flash the rom I would. So far so good! But When I put this MDA III (HTC TyTN II) on I still see this screen from T-Mobile for a while. Is there a possibility to get rid of this without throwing it away? I think of a firmware, but I don't see there is one. Ican't get it .HTC tells me to go to T-mobile and they tell me Idon't have a t-mobile phonenumber. Do I have to search for another firmware and if so where can I find it? Please your help! By the way :I bought this phone legally and second hand and want to bring it back in originally HTC shape.

http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs

[nondutch]

I did use the Hard-SPL and after that I could flash the rom I would. So far so good! But When I put this MDA III (HTC TyTN II) on I still see this screen from T-Mobile for a while. Is there a possibility to get rid of this without throwing it away? I think of a firmware, but I don't see there is one. Ican't get it .HTC tells me to go to T-mobile and they tell me Idon't have a t-mobile phonenumber. Do I have to search for another firmware and if so where can I find it? Please your help! By the way :I bought this phone legally and second hand and want to bring it back in originally HTC shape.
Flippolino: i think you're referring to the Splash screen
this is the thread you're looking for:
http://forum.xda-developers.com/showthread.php?t=334907
there are some examples, see if that is the part you want to change...
ND

[paul_flores]

Thanks XtreMe_G but asks me to file kaiser-HardSPL.exe is connected with activesync and my v1615 this on the botloader screen

TNKXX

[XtreMe_G]

Thanks XtreMe_G but asks me to file kaiser-HardSPL.exe is connected with activesync and my v1615 this on the botloader screen

TNKXX

did you reset your device, and did it boot into windows? if its still in the bootloader then try flashing with an original shipped rom with the device in the bootloader. if that doesnt work then contact gsleon3

[worldandworld]

There is some serious errors occuring when I unlock my At&T Tilt using the kaiser-simunlocker. I could install HardSPL and my Tri colour screen shows SPL-1.0 OliPof. but after running KaiserCustomRUU.exe on Step 1 my PDA shows only a blank screen with colour pixels. and when running kaiser-simunlocker.exe it returns Unlock code as ........ (only Dots). My Rom Version 1.62.502.0
ROM Date 01/17/08
Radio Version 1.27.14.09
Protocol Version 22.45.88.07H.

I could roll back to initial stage by running RUU_Kaiser_CINGULAR_WWE_1.62.502.0_radio_sign_22.4 5.88.07_1.27.14.09R2_Ship.exe that is downloaded from HTC site.
But still the SIM LOCK.

Plese help me if anybody has a solution

[Liquidwig]

Hi guys, hoping someone can help out a newbie. I have searched hi and low for my original radio version (1.27.12.29) but the only reference i can find is a discussion thread and a 56meg download which when un-zipped and placed in the step 3 folder does not work. Can anyone please help??

[resurepus]

it worked! Thanks a lot!

[ObiWanOvermann]

OK, I've been trying to HardSPL my AT&T Tilt since midnight last night and gave up around 2 in the morning. Using this file gets me the furthest but it gets me to that dreaded white screen. I've gone to the thread about the white screen, http://forum.xda-developers.com/showthread.php?t=354061, and that didn't get me any further. Got all the way through step 6 and ran the KaiserCustomRUU only to get an error, 240 to be exact. Says it can't start the Update Utility and closes. Anyway, using the file on this thread at least gets the phone to do something. What do I need to do to get this thing working so I can get rid of the AT&T ROM?

[abhi_k007]

[- reserved -]

hi

i want to unlock my HTC TyTn 2 device its a uk orange sim lock i dont know how to proceed i dont have the orange sim card with me, and i have tried teh unlocking software but unable to run any software as it says the supporting files are mising or corrupted and reinstalling might solve the issue, i am not ablt to intall/run any thing

plz help

Abhishek
kaushik.abhishek@yahoo.co.in

[biker200]

edited today

[FishooK]

I've finally thought, what the hell and went for it....man that was a smooth process....now running HardSPL and getting ready to install DuTTYs latest ROM....

[lmart08]

can you help me to unlock my att tilt please?

[revealor]

Every time I try to accomplish this instead of getting the tri color screen I get a blank white screen and nothing happens. Can anyone one assist me with this issue I have done this over and over with no results

[XtreMe_G]

Every time I try to accomplish this instead of getting the tri color screen I get a blank white screen and nothing happens. Can anyone one assist me with this issue I have done this over and over with no results

http://forum.xda-developers.com/showthread.php?t=354061

this solution is in this thread, in the stickies, in the wiki.

[redsoxsuck0570]

thnx bro it works perfect....just one warning tho....do not recover ur backup info!!!!!!it screws it all up...

[tubaking182]

i'm trying to flash the hard spl to my att tilt and it doesn't seem to be working, i followed the directions verbatim and my comp said that my tilt was no longer connected. i followed the advice from an earlier post to reboot the computer while my phone is still in the bootloader and the computer never found the drivers, does anyone know where i can find the drivers and manually install them on my computer? thanks in advance

[niti90210]

I have a lock Tilt 8925 which I am trying to unlock.
One of the steps involve is installing Hard SPL, but I cant sync my pc with the device. The activesync logo is green and window is telling me "
Your device is currently lock. To connect or syncronize with this PC, please unlock your device.

On the device, I hit unlock, but it's telling me I have enter too many wrong password. To continue entering password type "a1b2c3". After typing this, I return to the password screen. I guess I need a password to bypass this.

ActiveSync will not allow me to sync this device while in the lock mode. What do I do now?
Unlocking this phone require that Activesync is sync with the device...

Thanks

[XtreMe_G]

hard reset the device and the password will be gone, and so will all the setttings on the phone

[niti90210]

hard reset the device and the password will be gone, and so will all the setttings on the phone

How do you do a hard reset. I cant find it through the search.

Thanks

Would doing a hard reset let me bypass the password screen and let me sync the device with the PC; even though I dont have a At&T sim card (for US customer).

[niti90210]

hard reset the device and the password will be gone, and so will all the setttings on the phone

Found it. I held down the two soft buttons (about the Explorer logo and mail logo on front of the device) and hit reset witht he stylus....but it just resetted normally... Password screen is still there...

Am I doing this correctly?

[XtreMe_G]

obviously no

[P1Tater]

Found it. I held down the two soft buttons (about the Explorer logo and mail logo on front of the device) and hit reset witht he stylus....but it just resetted normally... Password screen is still there...

Am I doing this correctly?

you probably are not holding in the reset button with the stylus long enough.

[flashy]

what can i say... I have just hardspl'd my second kaiser (friends) and it went without glitch, flashed him the official HTC Rom too.

Thanks for the info on this forum guys, when i find my paypal account, i will donate to relevant people. :)

[3nabler]

I have been advised to post my problem here from elsewhere in the forum

hi guys,

I was halfway through running the hard spl program and it closed down, i just need some advice.

I got to the unplug and replug your device section where the tri colour and it says usb on my kaiser and the CMD promp window closed.

What can i do, can i just turn off my phone? or is this a big no no. HELP me please

how do i get out of this situation????

Thanks

[overhaulengines]

I have been advised to post my problem here from elsewhere in the forum

hi guys,

I was halfway through running the hard spl program and it closed down, i just need some advice.

I got to the unplug and replug your device section where the tri colour and it says usb on my kaiser and the CMD promp window closed.

What can i do, can i just turn off my phone? or is this a big no no. HELP me please

how do i get out of this situation????

Thanks

when you say half way, did you get to the tri color screen?

[MAXPOW3R]

I have a lock Tilt 8925 which I am trying to unlock.
One of the steps involve is installing Hard SPL, but I cant sync my pc with the device. The activesync logo is green and window is telling me "
Your device is currently lock. To connect or syncronize with this PC, please unlock your device.

On the device, I hit unlock, but it's telling me I have enter too many wrong password. To continue entering password type "a1b2c3". After typing this, I return to the password screen. I guess I need a password to bypass this.

ActiveSync will not allow me to sync this device while in the lock mode. What do I do now?
Unlocking this phone require that Activesync is sync with the device...

Thanks

i can't believe people were actually helping this phone theif. i guess i'm a little sore b/c i had mine stolen and had to replace it.

[crazigamer]

Should I try to install this on my ATT TILT or V7 ? or is V7 the one I should go for

[frank109]

my tilt never rebooted. never rebooted the screen just stay white.. is the white screen the tri-color screen?

[CozmicShredder]

my tilt never rebooted. never rebooted the screen just stay white.. is the white screen the tri-color screen?

No tri color is boot loader screen on all the Tilts... I get the white screen too and have to reboot...

I am using Windows Vista Ultimate 64-bit edition... AT&T TILT

ROM version: 1.62.502.0
ROM date: 01/17/08
Radio version: 1.27.14.09
Protocal version: 22.45.8807H

[futbolkeeper]

No tri color is boot loader screen on all the Tilts... I get the white screen too and have to reboot...

I am using Windows Vista Ultimate 64-bit edition... AT&T TILT

ROM version: 1.62.502.0
ROM date: 01/17/08
Radio version: 1.27.14.09
Protocal version: 22.45.8807H

Have you guys looked at the "White Screen" thread, if not check out the reading material in my signature and all will be explained. :D Or just click HERE (http://forum.xda-developers.com/showthread.php?t=383904). Your one freebie from searching, look for "White Screen" link. There is other helpful info there as well, so if you have a question/problem look there first.

[GuySparkz]

is this the best way to sim unlock the tilt from att? make sure the active sync icon is green on the pc or tilt? will this work for windows vista? thanks.

[mikerockwell1975]

Okay, I'm going to go try the white screen solution... thanks!

[leon sprouse]

I get error message when I try to use hard spl. I get past 3 screen to part that downloads for app 10 min. After about 2 mins error pops up . I remove battery etc. try again same thing keeps happening. Can anyone tell me how to stop this error.

[Feyroce]

Hi there,

Just started to install the Hard-SPL v1 on my Kaiser.
After 95%, got an error message !

If I restart the device, it starts automatically in bootloader mode but with the SPL-1.56.0000 !

How can I get out of the bootloader mode in order to restart the Hard-SPL v1 installation ?

[Feyroce]

Have a look at :
http://forum.xda-developers.com/showthread.php?t=371154

Use the boot command in the end !:)

[aznmasterpiece]

Prof, is there any way to flash Hard SPL with a memory card instead of activesync? My USB port on my Kaiser is not working. The port was made poorly. I have my replacement Kaiser but I need to return the old one in 10 days. Any help would be greatly appreciated. Thanks in advance.

[ahmad104]

i just bought Kaiser AT&T in Hong Kong. I think it is has been unlocked since I can put in any sim card.

I followed the instruction shown in this thread and that is what happened:-

1. while flashing the ROM, the progress bar stopped at 18%. A recovery steps was suggested by the RUU software.
2. I followed and the 3 color screen appear, then i tried re-flashing.
3. When I tried re-flashing, the progress bar stucked at 0%. Then, recovery steps come again.

Anyone has a solution for this? please....:( :confused:

[keeskoets]

I ran the hard-SPL and this is what happened:

==========copy from the dos screen============
Please make sure ActiveSync is enabled (GREEN icon in systray)
and hit ENTER to start...
=========================================
:) This is OK

==========copy from the dos screen============
Kaiser JumpSPL is running on your device, please check your device
screen and follow the steps until you see the tri-color screen.
=========================================

:mad: I followed the instructions on the device, but the phone got stuck at a white screen, not a tri-color screen. When I do a soft reset, the phone comes back to life.

So... No hard reset. Any suggestions???

I have a T-mobile Vario III version

:) Thanks in advance.

[felix999]

when started HTC Kaiser Hard-SPL v1 I click continue, but never come
the tree color mode.....the phone stopped....

what can I do:confused:

thx for help
felix999

[XtreMe_G]

I ran the hard-SPL and this is what happened:

==========copy from the dos screen============
Please make sure ActiveSync is enabled (GREEN icon in systray)
and hit ENTER to start...
=========================================
:) This is OK

==========copy from the dos screen============
Kaiser JumpSPL is running on your device, please check your device
screen and follow the steps until you see the tri-color screen.
=========================================

:mad: I followed the instructions on the device, but the phone got stuck at a white screen, not a tri-color screen. When I do a soft reset, the phone comes back to life.

So... No hard reset. Any suggestions???

I have a T-mobile Vario III version

:) Thanks in advance.

if you looked in the sticky you would see something that says.......

HardSPL will not install - WHITE SCREEN: SOLVED (http://forum.xda-developers.com/showthread.php?t=354061)

[Nicao]

Hey!
I did the Hard SPL a few times with Vista until i figured out that some users are reporting problems due to missing active sync and incompability of RUU with WMDC (without using the workaround)
So i did it with my XP pc twice and after all its the same result i had with vista:
The key-combi with I/O + camera and reset doesn't work as he doesn't show the bootloader but simply does a reset.
So i use the tool SSPL-KAIS.exe to open the bootloader manually and get

KAIS130
SPL-1.JumpSPL
CPLD-8
USB

nothing like OliPro etc.
Is this now fine to flash the rom or didn't it work properly?

Nicao

[XtreMe_G]

Hey!
I did the Hard SPL a few times with Vista until i figured out that some users are reporting problems due to missing active sync and incompability of RUU with WMDC (without using the workaround)
So i did it with my XP pc twice and after all its the same result i had with vista:
The key-combi with I/O + camera and reset doesn't work as he doesn't show the bootloader but simply does a reset.
So i use the tool SSPL-KAIS.exe to open the bootloader manually and get

KAIS130
SPL-1.JumpSPL
CPLD-8
USB

nothing like OliPro etc.
Is this now fine to flash the rom or didn't it work properly?

Nicao

press and hold the camera button and then reset to get into bootloader. sspl-kais, wont accurately show your bootloader, it loads a patched bootloader or something like that. if you want to enter bootloader by running a program i think you have to use enterbl.exe

[aarons6]

i am having troubles with a at&t tilt.
i have to run the jump spl 1.56 as i get the white screen.

i then get the 3 color screen that says
kais1*0
SPL-1.56.Jump
CPLD-8

USB

i run the customruu.exe to flash the spl and it says this
verifying information on my ppc
then it gives me the option to update

i push update
the screen switches to all white with the process bar.
it stays on 0% for a few minutes then times out.

it says

Error 262 : update error


ive done a few of these phones and never had any problems.

any ideas?

[mike1718]

omg, you saved my life :p thx!! :)

[trjons]

I've read the Wiki and searched and I can't find the answer to this question:

Can Hard-SPL be flashed via the MicroSD method?

[Nicao]

I solved the bootloader issue after a hardreset.
The device simply didnt react to the key combi in any way except for a rebooting...
Now its working fine... :)

[gutts77]

I am a noob. I followed the directions for hard-SPL v1. After the first step my tilt screen goes white. What am I doing wrong? I reset my unit and closed the program and tried it again. I keep getting the same result. Has anyone seen this before?

[JimmyMcGee]

I am a noob. I followed the directions for hard-SPL v1. After the first step my tilt screen goes white. What am I doing wrong? I reset my unit and closed the program and tried it again. I keep getting the same result. Has anyone seen this before?

Hi. Remember the Search is your Friend. I went to Google Typed "Kaiser White Screen Fix" and I found this. http://forum.xda-developers.com/showthread.php?t=372134

[gutts77]

Thanks , I know my bad. Right after I posted I did a search a found it. Rookie mistake, In the future I will search first. The fix worked. Thanks.

[dewhut]

ok i followed the directions for hard spl...i got the tri-color screen and unplugged and reconnected the usb but can't establish a green activesync icon. i deleted the partnerships, maybe that could be the problem but i was stuck in the tri-color screen so i soft reset to get my phone out of it. after that i started to lose my contacts and my phone kept sendin the same message over and over to the last person i text. i ended up clearing my storage and revertin back to factory. anyone have any idea?

[JimmyMcGee]

ok i followed the directions for hard spl...i got the tri-color screen and unplugged and reconnected the usb but can't establish a green activesync icon. i deleted the partnerships, maybe that could be the problem but i was stuck in the tri-color screen so i soft reset to get my phone out of it. after that i started to lose my contacts and my phone kept sendin the same message over and over to the last person i text. i ended up clearing my storage and revertin back to factory. anyone have any idea?

OK One thing at a time. If you are in bootloader, you won't get an ActiveSync Green icon.

Also by deleting partnerships. Your ActiveSync will delete the contacts from any Partnership that got deleted.

[dewhut]

OK One thing at a time. If you are in bootloader, you won't get an ActiveSync Green icon.

Also by deleting partnerships. Your ActiveSync will delete the contacts from any Partnership that got deleted.

this is all new to me, i've flashed my 8125 before and the tilt is a lil bit different. i just wanna successfully execute the cid unlocker so i can flash. i got to the part where it says unplug and reconnect to get the green icon but i can't. what should i do? and thanks for the fast response.

[XtreMe_G]

this is all new to me, i've flashed my 8125 before and the tilt is a lil bit different. i just wanna successfully execute the cid unlocker so i can flash. i got to the part where it says unplug and reconnect to get the green icon but i can't. what should i do? and thanks for the fast response.

it doenst say unplug and reconnect to get a green icon, it say grey icon, did you even read a word JimmyMcGee said?

[rcurtis13]

I am also wondering if Hard-SPL can be applied via MicroSD?

[dewhut]

it doenst say unplug and reconnect to get a green icon, it say grey icon, did you even read a word JimmyMcGee said?

and did you not read a word i said in my previous post? i did the grey icon and then it says in the following directions to reconnect it and get a green icon.

[XtreMe_G]

.....it says in the following directions to reconnect it and get a green icon.

no it doesnt!

unless you are refering to the RUU saying you have to have an activesync connection. but like JimmyMcGee you are not going to get an activesync connection in bootloader mode

[dewhut]

no it doesnt!

unless you are refering to the RUU saying you have to have an activesync connection. but like JimmyMcGee you are not going to get an activesync connection in bootloader mode

yeah that's what i'm referring to...the RUU. so what am i pose to do if i'm not gonna get an activesync connection? hit next anyway?

[XtreMe_G]

rofl yes. man.....are you cautious, if i were in your shoes, i would just hit next and see wat happens

[dewhut]

rofl yes. man.....are you cautious, if i were in your shoes, i would just hit next and see wat happens

i don't have the bread to fuck this one up...it's either be cautious or go back to my brick of a 8125

[blitter]

Found it!!!

Thanx,
Blitter

[PalmBayChuck]

I have a new Tilt that I'm going to give my wife for Mothers day and I haven't activated this phone yet because I don't want her old phone to die.

Would it be unwise for me to run HardSPL then load a new ROM before activation? I'm afraid it might cause AT&T to blacklist me or something!

Thanks.

[fizfreak]

Hi... Having followed the instructions I cant get passed 1st base? Active sync disengages after hitting enter on cmd and phonescreen just goes white! system reboots ok on soft reset! Where am I going wrong...? TYtn2-ROM 1.81.61.2 WWE operator version 24.181.1.612? Radio 1.27.14.32

Any advice welcome...

[XtreMe_G]

Hi... Having followed the instructions I cant get passed 1st base? Active sync disengages after hitting enter on cmd and phonescreen just goes white! system reboots ok on soft reset! Where am I going wrong...? TYtn2-ROM 1.81.61.2 WWE operator version 24.181.1.612? Radio 1.27.14.32

Any advice welcome...

http://forum.xda-developers.com/showthread.php?t=354061

you would have easily found this link in the sticky, in the wiki, or even by searching

[bajai]

Hi there i got my HTC Tytn II today from vodafone VODAFONE 1615 and i dont understand, really in mean that this. its my first htc foon how do i unlock my tytn II foon.
I have been reading and reading untill my eyes dropt dead butt i dont understand it, can anyone please help me how to do this en what do i need.
I have been reading that this program unlocks my foon and i have been reading that someone has Just installed the HTC ROM do i have to do that as well???
Where do i find all this can anyone help me in simple words so i can do this on my own

thanks :(

[XtreMe_G]

get some eye drop and do some more reading dude, you can start here:

http://forum.xda-developers.com/showthread.php?t=369282

this is for your own good, i'm sure you dont want to turn ur phone into a brick dont you :)

[bajai]

when i run this program after that when i'm done is my foon unlockt i mean can i insert any simcart in my foon is my foon sim unlockt????

[bajai]

thanx for the info

[Vistopher]

Installed perfectly, with a little user error on my part. All is good.

[XtreMe_G]

you dont need actvesync to connect once you are at the bootloader screen. just run the ruu and do the update

[jdorrego]

I got a message asking If I wanted to run the .exe, click on yes, thet I got the message software running, I waited for 10 minutes, but I never get saw the tri-color display, any tip?

Thanks
javier

[allstate973rd]

need help cant use active sync

[Imperium]

Can someone explain to me how i can help a friend?
He has a stock TyTN2 with no HardSPL and stock ROM.
he woke up and his phone was stuck at the bootloader..

i reckon he can't flash a stock WWE without HardSPL right?
and installing HardSPL isnt possible either within stock SPL right?

so what now?

[HiroshimaCC]

Hi!
After a long (and sometimes confused :p) reading of lots of topics from this forum, I decided to throw myself in and try to start playing with my TyTN II bought six months earlier :p ! So my first step was to Hard-SPL it, and after being somewhat confused about what method to choose (this one or the "new" one (http://forum.xda-developers.com/showthread.php?t=375583), I tried this one (since my device run on WM 6.0 in fact) and all worked great!

For those who wonder, my TyTN II is a Vodafone v1615 from the french operator SFR. No problem Hard-SPLing it.

And just to be sure, Hard-SPL just CID unlock the device, but not SIM unlock it, right?

Thanks you. Keep it up!

[Imperium]

Hi!
After a long (and sometimes confused :p) reading of lots of topics from this forum, I decided to throw myself in and try to start playing with my TyTN II bought six months earlier :p ! So my first step was to Hard-SPL it, and after being somewhat confused about what method to choose (this one or the "new" one (http://forum.xda-developers.com/showthread.php?t=375583), I tried this one (since my device run on WM 6.0 in fact) and all worked great!

For those who wonder, my TyTN II is a Vodafone v1615 from the french operator SFR. No problem Hard-SPLing it.

And just to be sure, Hard-SPL just CID unlock the device, but not SIM unlock it, right?

Thanks you. Keep it up!

Only CID. yes.

[HiroshimaCC]

Another question :p :
I read that official carrier's ROM contains a SPL. If I flash my Kaiser with one of these ROMs, will they replace Hard-SPL too ?
Or does the "SPL overwrite DISABLED" feature prevents that ? So what happens if the ROM try to flash the SPL with its own and can't because Hard-SPL doesn't allow it ?

[bigdawggs]

Are you using vista..sometimes it doesnt look for a new set of drivers for the Phone when its in tri color mode..try rebooting and leaving the phone in tri color mode...once you do that, start from scratch after it gets all the drivers installed
Hi, I'm trying to put the HTC ROM along with the Touch Flo Cube interface on my Tilt and I lose my Active Sync connection the second the Tri - color screen comes on and I can't get it back without pulling out the battery and starting all over again. How do I get past this? I wound up updating it with the new Tilt ROM but really want the HTC Rom instead. Thanks!

Using Windows Vista SP1

Current Tilt ROM Version 1.62.502.0
radio version 1.27.14.09

[hei_hei_hei]

Thanks for your great work.

[j_cart007]

I'm havin a problem to unlock the my fone. after doin step 1 succes when i do step and run the unlocker file it give the unlocking code like this : ........
and tht's it. i tried 00000000 and the same .......... but never worked.

can anybody help me out in this pls.

br.

[BigB4400]

I am trying to load the new "leaked WM 6.1" rom to my unlocked att tilt but it errors out, other threads with similar problems say that I need to run HardSPL so I came here. I run the Hard SPL on my hpone and as soon as I hit the accept on my phone to run the program the phones screen turns white and will not change unless I soft reset. What am I doing wrong?

[DaveShaw]

I am trying to load the new "leaked WM 6.1" rom to my unlocked att tilt but it errors out, other threads with similar problems say that I need to run HardSPL so I came here. I run the Hard SPL on my hpone and as soon as I hit the accept on my phone to run the program the phones screen turns white and will not change unless I soft reset. What am I doing wrong?

Try reading the 2nd Sticky on this forum, it has all the links to get you going, including...
HardSPL will not install - WHITE SCREEN: SOLVED (http://forum.xda-developers.com/showthread.php?t=354061)

Thanks
Dave

[jay9]

Followed instructions and ended up having to proceed with "White Screen Fix" for Hard SPL. No problems, everything went great.

Step 1 seemed to go as it should. I powered off phone and inserted alternate SIM to find that after initial AT&T screen and 3-G animation my screen just goes black. It seems to still be loading OS as I get keyboard tally as well as unlock code from Step 2?

Any ideas? I'm not optimistic about this one as searching this thread did not show any similar results.....

[XtreMe_G]

i'm guessing your rom is not compatible with the patched radio that step 1 installs

[housekid]

Use your MacBook Pro :)

I've seen this question asked before but I've never seen it answered.

Can you flash a Kaiser with a Mac?

Yes!

There are 3 different ways of running Windows on your Mac, well, 3 popular ways at least....

1. built in Bootcamp (have not tried this method)
2. Parallels (this program DOES NOT work, so I wont even link to it)
3. VMware Fusion (tested and works!) http://www.vmware.com/landing_pages/fusion2_beta.html

Download and install the trial of VMware Fusion and you can setup a virtual Windows XP machine on your mac!

You will need a copy of XP and the code/license.
You can use an actual CD or an ISO

VMware works to flash roms and upgrade radios.


Parallels does not work.


My job gave me a MacBook Pro so I could learn macs and support them at the college I work at.
The college is deciding to buy licenses for Parallels or VMware fusion.
So I had to install and test both of them on my Mac.
I've seen the question asked so I decided, what the heck, lemme try it.

I tried the newest version of both.
Parallels Desktop 3.0
VMware Fusion 2 Beta

Both installations were exactly the same.
XP Pro SP2
All updates
Office 2003 (Word and Outlook only)
All updates
ActiveSync 4.5

Whatever it is about Parallels though, the USB doesn't flow through the way it should and needs to for our phones.

VMware Fusion though works perfect!


And overall, I'm way more impressed with VMware.


The only reason I have not tried BootCamp is because you have to reboot your Mac into BootCamp.

With VMware and Parallels you are running those virtually inside a window on your Mac within your Mac OS.

With both of them you can click Full Screen and it switches you into full screen Windows mode and you'd think you had a PC laptop vs. a Mac.

Oh and for those that are not familiar with these Virtualization programs, you can run many different types of OS's, not just Windows XP.
and you can make as many as you want.

You load up the program and then select with machine you want to load.
It loads up in a windows.

and again, you can have as many different machines as you want with whatever different type of OS you want.

Great way to play, learn and experiment!

Great way to get the best of both worlds. Mac and PC/Windows.

And I have to say.... I've always been a PC/Windows guy.

But damn the new MacBook Pros are nice and since they are Intel based and can do the virtualization, if you have the money, get a Mac, they kick butt :)

very well made.

im impressed.








hello everyone,
i am using windows vista on my laptop and i have tried all day to try and do this and it just does not work at all.

I have recieved errors all day and still i have yet to CID unlock my AT&T Tilt. Any help would be great in trying to get this done with out bricking my device. thank you so much.

I have tried everything and don't know what is going on with this. I do not have any other computers that have windows xp on it all i have is a macbook pro laptop and the laptop that is running windows vista.

I really would like to get some good ROMS on my Tilt i am so bored with the ROM it has on it now lol.

[luay78]

Please help me with this issue.
Im having two devices of HTC 6800 sprint. One i bought it last year and the rom version 2.09.651.3 and radio version 1.47.01 PRI version 1.24.003 .

and now i have recieved one last week with newer version of 3.35.651.2 radio version is 3.35.04 pri version 2.00.003 // the question which i need help on it, Is i couldnt downgrade the second one newer one to the old version as my old device is working great. i need this new one same as the older. couldnt do this Please help me with steps i do to get it work normaly please ,,
Thank you

[luay78]

Please help me with this issue.
Im having two devices of HTC 6800 sprint. One i bought it last year and the rom version 2.09.651.3 and radio version 1.47.01 PRI version 1.24.003 .

and now i have recieved one last week with newer version of 3.35.651.2 radio version is 3.35.04 pri version 2.00.003 // the question which i need help on it, Is i couldnt downgrade the second one newer one to the old version as my old device is working great. i need this new one same as the older. couldnt do this Please help me with steps i do to get it work normaly please ,,
Thank you

[8sun]

I´ve I have the "T-Mobile MDA Vario III" and i´ll flash a free ROM.
Anyone has a german manual for "HTC Kaiser Hard-SPL v1"
I would understand that correctly without an error ;-)

information about my phone:
ROM Version: 1.56.111.4
Radio Version: 1.27.12.32
Provider: T-Mobile
OS: WindowsMobile 6 Professional
CE OS 5.2.1620 (Build 18125.0.4.2)

[eep02b]

How can i tell if my phone already has Hard-SPL installed?? i bought my phone off ebay, and it was unlocked, its running a custom rom, but before i change the rom, i wanna make sure its installed.... I'm using a mac, and was gonna install a rom from the micro-sd is why im asking this...

[gebak]

Does anybody know why I cannot unlock my Dutch T-Mobile Vario III (Kaiser), I have read all the threats but noting seems to work for me. It's either the white screen or the rgb + white screen but nothing happens. Is there a special reason why it's not working here?

[XtreMe_G]

Does anybody know why I cannot unlock my Dutch T-Mobile Vario III (Kaiser), I have read all the threats but noting seems to work for me. It's either the white screen or the rgb + white screen but nothing happens. Is there a special reason why it's not working here?

yes, found in the sticky at the top of this forum:

HardSPL will not install - WHITE SCREEN: SOLVED (http://forum.xda-developers.com/showthread.php?t=354061)

[gebak]

yes, found in the sticky at the top of this forum:

HardSPL will not install - WHITE SCREEN: SOLVED (http://forum.xda-developers.com/showthread.php?t=354061)

I also included this one when I wrote all threats, it wil just not work, that's the problem. Has anyone who owns a T-Mobile Vario III any idea?

[blagoy]

I had no problem at all with my T-Mobile Vario III. Read carefully. You are doing something wrong, unless T-Mobile updated the latest Varios with Dutch Necromancy :D

[BigB4400]

I followed your thread and it resolved my problem, thankyou very much.

[Tilt~n~Kicks]

not working on my At&t Tilt getting error right as i begin the process...... help!

[Tilt~n~Kicks]

ok so now im getting A white screen when

[XtreMe_G]

ok so now im getting A white screen when

ffs..........if you look in the sticky up top, or the wiki, or do a search, or even look a few posts back you will see this:

HardSPL will not install - WHITE SCREEN: SOLVED (http://forum.xda-developers.com/showthread.php?t=354061)

[eep02b]

How can i tell if my phone already has Hard-SPL installed?? i bought my phone off ebay, and it was unlocked, its running a custom rom, but before i change the rom, i wanna make sure its installed.... I'm using a mac, and was gonna install a rom from the micro-sd is why im asking this...

BUMP..............

[sd73ta]

maybe instead of bumping and waiting for an answer by reading the wiki or this thread it will tell you how to check if its installed

[eXceed]

Or even just run the app anyway???

[bubbleking2]

NVM, solved the problem.

[evan742]

Hi. I connected my AT&T tilt to the computer va USB and activesync is green. Ran HardSpl, and my phone said would I like to run the program and I said yes. And then the disclaimer came up and I said continue. Then my screen goes white instead of tri-colored and the USB connection is lost. What am I doing wrong? Please help. Thanks.