s200 G4 out after upagrade to wm6

[nyco]

Hi everybody,

i've got a big problem with my s200 G4.

when i flash it ti wm6, it work about 1 day, and after it freeze.
since, i can't turn on it. When i plug the power supply, no LED :/
I try the battery on an other S200 (i've got 3 ;) ) and the battery is ok.

Anyone got the diagram of the motherboard ?
Other idea ?

[riko06]

Hello
I have the same problem
Do you found the solution ?

[nyco]

Hi,

After open my S200, i think this is a capa out :/

Lot of people after upgrading the s200 have got the same problem. Freeze , reboot..freeze ....and never work again :(

Have you got a red led ? orange ?

charging ok ?

[b2hteam]

i had the same probleme
the solution is to remove the battery for 24 hour after plug it in the usb with ur computer until the charger leed appear
after change the rom to a wm5 rom and it will work perfectly.

[b2hteam]

i think the reason of this probleme is the ipl version must be 2.20 beafore upgrade to wm6

[nyco]

Hi,

I test your technic, but doesn't work. Now, when i plug the charger, i've got the red led 1 second, and ....nothing. it doesn't won't to switch on :(

i try the trick with the pins...but doesn't work :(

[nyco]

Hi,

I test your technic, but doesn't work. Now, when i plug the charger, i've got the red led 1 second, and ....nothing. it doesn't won't to switch on :(

i try the trick with the pins...but doesn't work :(

[igord]

Hi,

Same problem, when I put the charger in I got one sec red led. But I can hard reset or enter bootloader, when on the charger, but there is no way to put USB when the charger is in. Which pins are + and - battery?

[l3v5y]

If any Prophet can enter bootloader, it can be recovered. See the wiki for a how to.

[nyco]

hi everybody.

After trying again and again the pin trick, the s200 went to a blank screen, white with the red led.

I wish it reboot again...

if you got any idea to enter bootloader when i've got white screen ....

[l3v5y]

Can it enter bootloader? Hold down the camera button and soft reset.

[Jahn11]

i have G4 with ipl and spl 2.20 and on switching on it freeses with white screen. it goes to bootloader, but except WWE ship 220 update others can't be loaded.
Sometimes it goes to screen "Windows mobile", but then freeses.
Is any solutions? Thanks

[l3v5y]

i have G4 with ipl and spl 2.20 and on switching on it freeses with white screen. it goes to bootloader, but except WWE ship 220 update others can't be loaded.
Sometimes it goes to screen "Windows mobile", but then freeses.
Is any solutions? Thanks

Can you perform a hard reset?

[nyco]

Can it enter bootloader? Hold down the camera button and soft reset.

I can't access to bootloader. :/

[l3v5y]

I can't access to bootloader. :/

Can you do a hard reset?

[nyco]

Yes i try again and again...but ...

white screen ( flashing )and red led :/

snif snif

[l3v5y]

Try to enter bootloader (soft reset and camera button), it doesn't matter if it shows nothing, disable activesync connect through USB, and try to flash a WM5 ROM.

[nyco]

Ok, i'm trying it this evening...
But when i plug the s200 on my PC, nothing show the phone is connected (USB mode on winXP or on the tel )

Well...i tell if your tips work tomorrow =)

[l3v5y]

The point of this technique is to reduce the number of points it could fail, and remove the requirement for the previous ROM to work. The RUU for shipped ROMs can establish a connection without activesync.

[nyco]

Well ...

But i forget to say ...the s200 can't power on when it's plug on USB...it power only with the charger :(
With USB, no LED, no screen ....


Have you got a tips to connect the phone with charger+USB cable ?

[l3v5y]

Is the battery charged? Normally, USB doesn't provide enough power for a device, unless it is syncing or running normally. I have no idea if it's possible to alter the cables to provide the power given, so I would look around or wait until someone knows what to do...

[nyco]

Battery 100% (tested with another s200)
I think it's dangerous fot the PC if i plug the charger+usb. You send 1mA in to the USB port whose supporte only 500mA out ....

I'll testing with the hub with external power...and wish it work again ...

Thx a lot man :)