jasjam Stuck in boot process

[ehab1234]

I upgraded to WM6 to Schaps_WM6Pro_WWE_4.01_Full.exe after then i tried to go back to
838Pro_HK_ENG_WM6_Upgrade_20070712.zip , the operation stopped on the 20% and
crash Now I just have a 4 color screen showing HERM100 ,IPL-1.04 then HERM100 , SPL-2.03
i have tried to flash more than 12 Rom from wm6 and wm5 with no luck, i have tried to flash
the Radio only ver 1.54 and 1.51 and 1.50 and last 1.47 with no luck all stop and 1%
tried mtty.exe set commend 14 0, 1nb command not available, i think i have Type 2 bricks: Stuck in boot process




mtty output here:
-------------------
Cmd>

Cmd>task 32
CID: Wait interpreter timeout
Level = FF

Cmd>info 2
HTCSF kEØ(HTCE
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block

Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1900
Partition[2], type=0x25, start=0x3200, total=0x1A900
Partition[3], type=0x4, start=0x1DB00, total=0x1CD00

CE Total Length(with sector info) = 0x3C4D800
CE CheckSum Length(without sector info) = 0x3B60000

Cmd>
-----------------------------------------------------
other info:
Model: jasjam - imate
ROM Before Flash: Schaps_WM6Pro_WWE_4.01
Radio Before Flash: ?
Bootloader Before Flash: 1.04
Flash failed at: 1%
Flashing Radio: 1.54. - 1.51.- 1.47
Bootloader After Failure: 1.04
CID Before Failure Super CID: Yes
CID Corrupt: ??
Radio Corrupt: ??
No GSM Error: Yes
Stuck In Bootloader: ??
Stuck On Windows Mobile Splash: Yes
Can boot into OS: No
Tried mtty command set 14 0: Yes
Current Device Status: unusable -cannot boot , can see wm6 green screen before today screen

how can i fix it
many thanks
ehab

[aeayk]

Thank you Ehab for bringing this issue, I have the same problem exactly, which happened when I installed Radio 1.54.07.0, which was installed completely, but the JasJam never been able to boot beyond the second splash screen with "No GSM" singe.

I tried the same thing you did and I have the same bad luck! :confused:

Heeeeeeeeeeeeeeeelp
Please,

Thank you

[aeayk]

I'm wondering why when I do
task 32
I get Level = FF
not Level = 0
as mentioned in the Hermes Upgrade Proplems (http://wiki.xda-developers.com/index.php?pagename=Hermes_BootloaderMFG) post
Heeeeeeeeeeeeeeeelp
Please,

Thank you

[aeayk]

My solution for the problem by usnig the SD card method,
get an SD card reader and do the followings:

1- Use your Clean formated SD card (formated as FAT32)
2- find original operating system, extract it with WINRAR, if its not already extracted.
3- When OS extracted, you will have 2 files or more.
4- Look for the file called "RUU_signed.nbh" or similar that ends with ".NBH" (lik "herming.nbh")
5- Copy the "RUU_signed.nbh" file or what ever similar that end with .nbh to the SD card
6- Rename the file to "HERMIMG.nbh"
7- do not use the " " meaning rename it as HERMIMG.nbh
8- Reboot your device to bootloader, (hold Ok button on left side and POWER button at same time and stick with stylus in RESET on bottom).
9- that will start bootloader and in few seconds the falshing will start, it will ask you to confirm flashing on screen by pressing the power button. (screen shot (http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing))
10- Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
11- a message will say flashing completed.
12- Do soft reset, volah- device workes.

that worked for me, I hop it will work for you

enjoy