FLASH disaster

[ManStan]

I was becoming an expert in flashing...but the cable became undone during a flash :-(
Now it restarts to a blank screen with R1.50.08.11 / G32.83.7020 etc. but goes no further.

Computer no longer sees device.

Used hard keys to go into bootlocker. (IPL 0.50 / SPL- 1.07.000)
My VISTA :-( computer sees device.
Then try RUU, but this gives a 270 error.

Tried moving to XP, but the computer does not install the software for the USB port, so now the RUU gives 200 error. Arrgh.

Question: How to update from a very corrupted ROM? Or where can I find the drivers for the USB port, for XP. and if I do can I do the update from the hard bootlocker?

Any help really appreciated!

MS

[ManStan]

Found USB drivers for Windows XP:-)

But getting identical problem as with Vista :-(

Device not seen unless in bootlocker mode.
RUU starts and after 1% quits with 270 error - image file corrupt.

Tried RUU a hard SPL (olipro) but same 270 error occured.

Help still needed...

MS

[Stratos74]

I think you have to flash original HTC rom prio to try other roms

[sailer1983]

i got a similar problem here, my vista can find trinity only when it is in bootloader mode.

my experience is that connect tinity to vista when it is in bootlader mode, then i can flash a new rom.

after that tinity can sync with vista only via bluetooth.


for your case, maybe you really need restore your trinity to official rom first.

[fktsndr]

i got a similar problem here, my vista can find trinity only when it is in bootloader mode.

my experience is that connect tinity to vista when it is in bootlader mode, then i can flash a new rom.

after that tinity can sync with vista only via bluetooth.


for your case, maybe you really need restore your trinity to official rom first.

Maybe helps:

http://trinityguides.info/index.php?option=com_content&task=view&id=20&Itemid=66

[ManStan]

The trinity upgrade guide does not help here.
I can connect to device I have sorted out all the VISTA and XP issues.

The problem is at 1% status the 270 error occurs.

The telephone is actuall a Swisscom 1510. Original ROM was lost in first flashing, have searched but not found official update.

Is there a mini-ROM or a windows WM5 lite ROM which may overwrite what happens while still using the hard bootloader?

MS

[atropo]

Use SD card method.
See wiki page.
Bye

[Bobo Xni]

Hi,

...or .... MTTY Procedure....

BYE, Bobo ;)

[ManStan]

Tried SD card method - nothing happens. Just sits in Bootloader :-(

[wolfmenace]

Try this procedure

In windows Vista use the attached driver in order to recognize your Device.
If your device is already recognized from windows vista replace the drivers with the drivers in the zip drive.

You have to use the drivers in the attached file not the windows default drivers VERY IMPORTANT!!!

After your Windows vista recognized your device try to flash it
Cheers ;)

[ManStan]

Thanks for all the help....but still I am having no success.

The HTC trinity is recognised in both Vista and XP when I use bootloader. (ie HTC USB SYNCH in device manager. Without boot loader the device is more or less dead.

I tried the SD crard trick - nothing happens.

Tried mtty.exe - just get cannot open USB port (on both VISTA and XP).

Nevertheless, the bootloader sees the USB port and the RUU goes to 1% then stops so some communication is happening.

Any other ideas?

MS

[atropo]

The final and, j' m sure, the definitive solution:
Try this one http://forum.xda-developers.com/showthread.php?t=308691&highlight=stack+in+bootloader

[ManStan]

Just before I try splxploit, as a note I got this out of mtty

Cmd>info 8
Block 0x0(0) is Reversed block
...
Block 0xC(12) is Reversed block
Block 0x335(821) is BAD block !!!

Seems my problem must be here. Is there another fix besides splxploit?

MS

[atropo]

Install Olipro hardspl 1.20.
Bye

[tuannghia1985]

Dear, carefully look that thread again. Stack overflow for Trinity.

It's all my advise. I think you don't do right "Stack method" to get out your problem.

Best regard.(rest calm and do it again).

[tuannghia1985]

Uhm, try to download some rom again? and try Rom NVID (no vendor ID) for example. ???

[ManStan]

Quick update...

Tried SD card - get 00068002 loading .... then goes to IPL0.5 SPL 1.07

mtty info 8 shows bad blocks
task 2a doesn't clear bad blocks because of CID lock

Tried various hard-SPL OLIPRO 1.2 1.3 etc, to unlock CID - to no avail.

Can the CID not be unlocked through mtty?

MS

[nealed]

Quick update...

Tried SD card - get 00068002 loading .... then goes to IPL0.5 SPL 1.07

mtty info 8 shows bad blocks
task 2a doesn't clear bad blocks because of CID lock

Tried various hard-SPL OLIPRO 1.2 1.3 etc, to unlock CID - to no avail.

Can the CID not be unlocked through mtty?

MS

So you haven't yet tried splxploit?

[ManStan]

:D YESSS!

POF you are a genius - Splxpoilt worked a dream.

Had to run unbrick.bat once. Hit soft reset, and run again as explained in the readme.
This got a good SPL on the machine - then a standard RUU worked a dream.

At the same time I got the SD card update working too...

OK, OK, so I should have tried splxpoit earlier. But I think I had to do the rest first to understand what was going on.

Strange thing is if I look at my machine again under mtty, there is still the Bad block (821). Who cares, I am unbricked!!!

By the way, this board is just completely amazing.

THANKS TO ALL....

[Luzik2oo6]

could you help me . how did you repair your spv?

[Luzik2oo6]

Computer don't see my device. what i should i do?

[ManStan]

Step one go into bootloader (see Wiki page)

Step 2: Plug in USB cable - USB should be written on bootloader window.

After that note the IPL and SPL programs that are running see Tricolour screen.

As a check look at device manager on Windows computer and you should see the mobile device.

For certain actions (mtty and splxploit programs) USB connection should be dissabled in activesynch. For others, such as the standard RUU it should be activated.

Everything is better with XP than VISTA.

Good luck,
MS

[Luzik2oo6]

hi thx my spv works:) but after instalation wm6 my screen is white. I see start icon , batery status ,contacts button and calendar button . I do wrong something ?

[Luzik2oo6]

help me plz:(

[hoja67]

help me plz:(

.... you start over.

Follow the tutorial here and you can't go wrong!

http://www.trinityguides.info/

Cheers!

hoja67

[Luzik2oo6]

thx thx I dont disable usb when i Flasch it:)