HTC P3600 don't want to flash! [Archive]

nightblade

8th December 2007, 08:00 PM

Hi guys,

this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.

I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!

I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)

Anyone can help me to flash (with lowest risks) my P3600 again? :( :( :(

Thanks to everybody! :)

nightblade

13th December 2007, 10:05 AM

no ideas guys? :confused: :confused:

nightblade

15th December 2007, 09:55 PM

so no one can help me with an idea??? :confused: :confused: :( :(

Jackuuuuu

16th December 2007, 07:06 AM

What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.

nightblade

16th December 2007, 12:39 PM

What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.

it's a P3600

stepw

20th December 2007, 08:37 PM

Do a hard reset and flash an OFFICIAL ROM from SD-card

tnyynt

20th December 2007, 09:38 PM

Switch to Des' Crash Proof SPL and try flashing the ROM straight from SD card.
This should work.

nightblade

22nd December 2007, 03:27 PM

thank you very much. I've already tried to change to Des Crash Proof but at about 13%-14% it gives me an error :( when I reboot by softreset the system is always the same. Is it normal? Is there a specific procedure to change SPL software? :confused:

stepw

22nd December 2007, 09:01 PM

If it works at all after SPL flashing, then you must have followed all procedures. Try flashing Olipro's SPL and scan for bad blocks in flash.

jmermel

29th December 2007, 07:25 PM

Hi guys,

this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.

I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!

I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)

Anyone can help me to flash (with lowest risks) my P3600 again? :( :( :(

Thanks to everybody! :)

Make sure that your SD card it out