HardSPL will not install - WHITE SCREEN: SOLVED (UPDATE 01. March 2008)

[jockyw2001]

For those who cannot install the HardSPL and don't wonna read this thread (http://forum.xda-developers.com/showthread.php?t=349476), here is the solution:

1a. download the 5 attached files
1b. pull out the battery, REMOVE SIM and SD CARDS !! and reinsert battery (this step *is* important)
1c. connect your PC to phone with a USB cable
2. copy JumpSPL1.56-KAIS.exe to your device and run it (make sure the USB cable is still connected). If you still get a white screen then reset your device and now try JumpSPL1.93-KAIS.exe
3. after a few seconds "USB" appears on the phone display
4. unplug and replug the usb cable
5. deselect "Allow USB connections" in Activesync connection settings
6. now flash hardSPL (run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC)

Notes:
1. if when running a JumpSPL an error is shown try to application unlock your device first with SDA_ApplicationUnlock (you must run this on PC with an activesync connection via USB cable). If you still get errors you need to hard reset your device (power off, keep both left and right navigation keys pressed and power on)
2. With the JumpSPL you should *not* flash radio roms, OS roms or full roms. The JumpSPL is only needed to flash a HardSPL (or SPL)

[Geraldous]

Way to go!
My tilt is arriving on boxing day, now i have everything ready for flashing. Thanks for collating everything when the information was available!

merry christmas :)

[vanydotk]

You're awesome!

[stozmon]

jockyw2001,

I just wanted to say that even though I never had this issue on my Tilt, I have been following your progress closely from the start and just wanted to commend your Herculean effort in attaining the solution. It is hard working, selfless individuals like yourself that embody the spirit of this forum and the developer community.
BRAVO!

[mfrazzz]

Amazing work and congrats on solving this! Have a Merry Christmas and I sent you a donation via PayPal. I have a couple of friends getting Tilts and they will be thrilled to see they can flash custom roms if they choose to do so!

[xconradx]

beautiful... excellent work man. greatest gift I'll get this Christmas!

[subnet99]

Thanks for all the hard work!

I just sent you $50.00 donation.
Merry Christmas!

[subnet99]

Admins might want to make this thread a sticky.

[a in yul]

thanks, will have to try it once i get back home..!

UPDATE:ok, couldnt wait, tried it out, and it worked, many thanks, this was a nice xmas gift made even nicer by your efforts to make this possible..!

NB: i was somewhat worried because of a few beginners' errors;

1.i wasnt sure where to install the Jumpspl1 hence i just saved onto phone, is that ok and/or should i remove(move) it?

2.initially i got an error, went through the Recovery feature, and tried again, 2nd time around it step 1&2 worked, and then loaded Duttys rom

3. Thanks a million, your generosity of time is exemplerary,

Merry Xmas to one and all..!

PS:what are the prereqs for updating the radio(Provider=Fido), is usually more recent better or is it via trial and error?
PPS:Sign of my thx sent via PP.

[pdtp]

Thanks for all your hard work i sent you a donation via pay-pal.

[Petersonz]

Thank you sooooo much!

[Sleuth255]

Nice patch jockyw2001! :)

[mofoliar]

For Sure! thanks

[a in yul]

Sie haben einen ungültigen Betrag eingegeben. Überprüfen Sie, ob Sie das Dezimalkomma korrekt verwendet haben und ausschließlich numerische Werte eingegeben haben. Bei einem Betrag von $5,00 USD geben Sie beispielsweise 5,00 ein.

trying to participate via PP, no luck..; let me know, thx.

[weddellkw]

After running JumpSPL I get to the tri-color screen, pull the usb after 'usb' comes up, plug it back in, and nothing (tri-color screen stays till i reboot)...
A soft-boot brings the Tilt back to life.
SIM card and SD are removed.

My version numbers seem to match people who successfully flashed.

Stumped...

[vanydotk]

After running JumpSPL I get to the tri-color screen, pull the usb after 'usb' comes up, plug it back in, and nothing (tri-color screen stays till i reboot)...
A soft-boot brings the Tilt back to life.
SIM card and SD are removed.

My version numbers seem to match people who successfully flashed.

Stumped...

*sigh.. young gun, back in my day we had to run everything ourselves, it wasn't put in a neat little package that did everything for us.

After you get into the tircolored screen and plug your USB back in, you have extract and run hard spl (using the file on the first page of this thread).
http://forum.xda-developers.com/attachment.php?attachmentid=63026&d=1198513037

That one to be exact.

[eltoro]

Awesome. Thanx I'm planning on buying a second Tilt. I didn't have any problem with the first one and has D 1.57.00.00. But you never know.

[mofoliar]

Running Sleuth V1.1.. Runs good. nice software

Rom:1.1 Sleuth
Rom Date:8/28/07
Radio Version:1.27.12.11
Protocol:22.45.88.07H

Thanks again for the update bypass

Merry Christmas~

[weddellkw]

*sigh.. young gun, back in my day we had to run everything ourselves, it wasn't put in a neat little package that did everything for us.

After you get into the tircolored screen and plug your USB back in, you have extract and run hard spl (using the file on the first page of this thread).
http://forum.xda-developers.com/attachment.php?attachmentid=63026&d=1198513037

That one to be exact.

Tried this, get an error 240 - can not open file w/ the hardSPL and the Splash executables.
Should have mentioned that in the last post. Sorry. Assumed there was a reboot or something coming after resetting the usb connection...

[lowreeds]

OK maybe this can be an example for others (and me)
.
I was able to flash a splash so I got cocky and tried to flash a cooked rom via kaiser kitchen.

Now I'm stuck in the boot loader.

I then tried to flash RUU_Kaiser_CINGULAR_WWE_.exe and got "invalid vendor id".

Then I tried to flash hard_spl from the first post. 0%

I've searched for hours trying to find a fix.
I tried a hard reset. No dice.
I've got mtty running and ran the boot command.
Fill RSVD information for block 288 to 309
Storage start sector=0xAB80, total sector=0x10740
Storage start block=707, total block=1053
Total Bad Block in CE: 1

Erase physical block from 996 to 2032

si backup: Erase physical block from 2032 to 2048
It still wont boot.
Please help...
boot screen shows:
RUUNBH
KAIS1*0
SPL-1.56.0000
CPLD-8

again please help....

[vanydotk]

OK maybe this can be an example for others (and me)
.
I was able to flash a splash so I got cocky and tried to flash a cooked rom via kaiser kitchen.

Now I'm stuck in the boot loader.

I then tried to flash RUU_Kaiser_CINGULAR_WWE_.exe and got "invalid vendor id".

Then I tried to flash hard_spl from the first post. 0%

I've searched for hours trying to find a fix.
I tried a hard reset. No dice.
I've got mtty running and ran the boot command.
Fill RSVD information for block 288 to 309
Storage start sector=0xAB80, total sector=0x10740
Storage start block=707, total block=1053
Total Bad Block in CE: 1

Erase physical block from 996 to 2032

si backup: Erase physical block from 2032 to 2048
It still wont boot.
Please help...
boot screen shows:
RUUNBH
KAIS1*0
SPL-1.56.0000
CPLD-8

again please help....

Maybe Mitty can bring your device back to life.. but just a piece of advice and I'm not trying to kick you while you're down but ALWAYS ALWAYS ALWAYS ALWAYS ALWAYS ALWAYS install Hard SPL before tryin to install roms!

[lowreeds]

well i found this thread
http://forum.xda-developers.com/showthread.php?t=334693&highlight=invalid+vendor+id
and was able to flash this rom
http://rapidshare.com/files/53403690/RUU_Kaiser_ATT_WWE_1.51.502.0_Radio_sign_22.45.88. 07_1.27.11.31_Internal.exe

[centella]

jockyw2001

you are a hell of a gooooood cientist

[a in yul]

i was successfull in using Duttys new rom, thanks to this HardSpl; i noticed though that when i turn the phone on; i now have the following on my white at&t logo screen;

<<DEVICE NOT FOR SALE DEMO UNIT ONLY>>

i have that on the top and the bottom of the screen.

Is this the norm, or have i somehow initiated this..? any help would be appreciated!

[jockyw2001]

OK maybe this can be an example for others (and me)

Please help...
boot screen shows:
RUUNBH
KAIS1*0
SPL-1.56.0000
CPLD-8

again please help....
Your device is still in ROM update mode ("RUUNBH").
Connect with MTTY and type "task 8" will clear that mode.

If the device won't boot into Windows Mobile you will have to flash an original ROM with model and vendor ID (CID) matching to your device.
Use "info 0" to for getting Model ID and "info 2" for Vendor ID (CID).
ModelID is 9 digits and VendorID is 8 digits.

While you are at it, please make a note of the entire "info 0" output.
Mine is:

Cmd> info 0
Platform Model ID:KAIS13000
Platform HW Board ID:31, PVT1

[jockyw2001]

i was successfull in using Duttys new rom, thanks to this HardSpl; i noticed though that when i turn the phone on; i now have the following on my white at&t logo screen;

<<DEVICE NOT FOR SALE DEMO UNIT ONLY>>

i have that on the top and the bottom of the screen.

Is this the norm, or have i somehow initiated this..? any help would be appreciated!
Just flash another splash screen if you don't like it.

[lowreeds]

Your device is still in ROM update mode ("RUUNBH").
Connect with MTTY and type "task 8" will clear that mode.

If the device won't boot into Windows Mobile you will have to flash an original ROM with model and vendor ID (CID) matching to your device.
Use "info 0" to for getting Model ID and "info 2" for Vendor ID (CID).
ModelID is 9 digits and VendorID is 8 digits.

While you are at it, please make a note of the entire "info 0" output.
Mine is:

Cmd> info 0
Platform Model ID:KAIS13000
Platform HW Board ID:31, PVT1

no longer stuck due to thread mentioned in my previous post.
hopefuly I won't be needing mtty again.
thanx for the info and the killer tools.
im running my first home cooked rom!!!
just like my old treo 650 but better.

[a in yul]

Just flash another splash screen if you don't like it.

ok, will do that, now the next question is, as a newbie, how do i or rather where do i get another splash screen?

Thanks for a wonderful programme; now i can finally take advantage of my tilt with your help!! Merry Xmas & Happy New Year to one and all...!!

PS:PayPal sent, thank u once again!

[jmat]

Thanks man, you rock. I was needing this so I could flash a new radio (AT&T's default radio sucks for some reason). Donation is on its way.

Also, I can verify this works on a MacBook Pro using Parallels.. with a lot of stuff happening on the "Mac side"... but I like living life dangerously. ;-)

edit: Something funky with USB won't let ROM's successfully flash on a Mac using Parallels. Using the SD Card method works great, though. I just needed Windows to flash HardSPL. Whew. :) .. what's weird is I never had a problem flashing my Hermes via Parallels+Mac... Can't figure out why... I just retried flashing a ROM to my Hermes, and it went without a problem. Kaiser never gets past 10-15%. Odd.

[jockyw2001]

ok, will do that, now the next question is, as a newbie, how do i or rather where do i get another splash screen?

pof has a nice thread here (http://forum.xda-developers.com/showthread.php?t=334907)

Thx for ur generous donations guys :)

[TiltedAz]

Pay Pal sent. I should have some time this weekend to try it. Thanks in advance for your hard work!

[dayofpain]

alright i feel like a complete idiot here and i will gladly donate if someone can guide me through this.

ok so i move the jumpspl file to the phone via activesync, however on the phone itself i cannot find it anywhere even though it says its been sync'd. its almost as if its a hidden file.

i tried running the jumpspl on the laptop and its not a win32 application.

i tried reflashing with the roms and i get to the tricolor usb screen and it sits at 0% and then gives me connection error 262.

so i guess my questions are where the hell do i run the jumpspl from if it wont run on the laptop and it wont show up in the phone even though when i explore it on activesync it shows its there.

[Sleuth255]

What folder did you move it to when you copied it using explorer mode on activesync? ;)

[dayofpain]

What folder did you move it to when you copied it using explorer mode on activesync? ;)

about a billion different ones to try to get it to show up on the device.

every folder i tried activesync says its there when double checked but when i really look at it, its not there.

again, for your help i plan on donating once this is all said and done.

thank you

[bleitner]

thank you for the great summary on solving this, but I need to get my original at&t spalsh screen back that doesn't say "not for sale" on it. does anyone have an .nbh of it?

[Sleuth255]

about a billion different ones to try to get it to show up on the device.

every folder i tried activesync says its there when double checked but when i really look at it, its not there.

again, for your help i plan on donating once this is all said and done.

thank you

what do you mean by "really looking at it"? You must use file manager on your Tilt and navigate to the folder. I always move stuff to /temp when I'm using activesync then navigate there with file manager. If you are doing this and can't see it then the jumpspl file itself may be hidden.

[lowreeds]

alright i feel like a complete idiot here and i will gladly donate if someone can guide me through this.

ok so i move the jumpspl file to the phone via activesync, however on the phone itself i cannot find it anywhere even though it says its been sync'd. its almost as if its a hidden file.

i tried running the jumpspl on the laptop and its not a win32 application.

i tried reflashing with the roms and i get to the tricolor usb screen and it sits at 0% and then gives me connection error 262.

so i guess my questions are where the hell do i run the jumpspl from if it wont run on the laptop and it wont show up in the phone even though when i explore it on activesync it shows its there.

1. power down your Tilt and remove sd card and sim card
2. connect Tilt to laptop via USB cable.
1. open "Mobile Device" folder via "Explore" button on ActiveSync.
2. copy JumpSPL1.56-KAIS.exe to the directory that it opens up to. Mine says "Mobile Device". That will be your "My Documents" directory on your Tilt.
3. use file explorer on Tilt to navigate to "My Documents" directory. Keep hitting "up" till you cant go any farther. The directory should be there.
4. Open "My Documents" and run JumpSPL1.56-KAIS.exe
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable.
7. run KaiserCustomRUU.exe from the flash-hardSPL directory on your laptop. Tilt will reset.
8. flash rom.

hope this helps...

[dayofpain]

no matter what i do it says the file is there on the computer side but when i look in literally every single file folder on the phone itself its just not there.


i really want to kill myself at this point, im so frustrated.

[deadlywingz]

ok the hardspl worked great now here is the other probalem while i waz loadin in dutty 's rom itwent to 18 percent and stoped and now when i try to re flash it wit n e rom including dutty's rom and the at&t rom it doesnt move from 0 percent n e ideas from n e one

[lowreeds]

no matter what i do it says the file is there on the computer side but when i look in literally every single file folder on the phone itself its just not there.


i really want to kill myself at this point, im so frustrated.

when using file explorer click "menu" and be sure "show all files" is checked.

Happy new year!

[requistp]

I copied JumpSPL1.56-KAIS.exe to my Tilt and executed it. I got the tri-color screen, and then it said USB. When I unplug and replug the USB cable, nothing happens, no reset. Tried three times, same every time.

I tried reseting the phone myself, and then running KaiserCustomRUU, but it froze at 0% both times I tried. ROM wasn't corrupted or anything, it reset fine.

Thanks for any help. BTW, this is a new Tilt, bought just about a week ago, if that matters.

[jslatone]

1. power down your Tilt and remove sd card and sim card
2. connect Tilt to laptop via USB cable.
1. open "Mobile Device" folder via "Explore" button on ActiveSync.
2. copy JumpSPL1.56-KAIS.exe to the directory that it opens up to. Mine says "Mobile Device". That will be your "My Documents" directory on your Tilt.
3. use file explorer on Tilt to navigate to "My Documents" directory. Keep hitting "up" till you cant go any farther. The directory should be there.
4. Open "My Documents" and run JumpSPL1.56-KAIS.exe
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable. device will reset.
7. after Tilt boots back up run KaiserCustomRUU.exe from the flash-hardSPL directory on your laptop. again Tilt will reset.
8. flash rom.

hope this helps...

I was trying to comlpete all these steps a few times but getting stuck on step 6 of the instructions above.
After getting into tri-color screen with KAIX1*0/SPL-1.56.Jump/CPLD-8 and unpluging USB the screen still displays "USB" label and the yellow power light is still on (even when USB is unplugged).
Also when I plug in USB cable back in Tilt does not resets....
Tried to do the rest of the steps and still getting AT&T rom remaining.

Any help???

:confused:

[jhernand1102]

I was trying to comlpete all these steps a few times but getting stuck on step 6 of the instructions above.
After getting into tri-color screen with KAIX1*0/SPL-1.56.Jump/CPLD-8 and unpluging USB the screen still displays "USB" label and the yellow power light is still on (even when USB is unplugged).
Also when I plug in USB cable back in Tilt does not resets....
Tried to do the rest of the steps and still getting AT&T rom remaining.

Any help???

:confused:

I thinks there is some confusion here...your device will not reset but you will here active sync disconnect then you will here the usb connect, you should see a usb connection established. Once you here this happen then run through the rest of the process. Once you have completed this process you should verify that it has taken the hardspl by enter the bootloader mode..press and hold the power+camera buttons and reset it with your stylus, contine to hold the buttons after releasing the stylus and wait for the tricolor screen you should seen the new spl info...if this is correct then you can flash any rom you wish....hope this helps

[lowreeds]

sorry guys. my step-by-step was wrong at step #6 & 7 which i've corrected.

try this...

1. power down your Tilt and remove sd card and sim card
2. connect Tilt to laptop via USB cable.
1. open "Mobile Device" folder via "Explore" button on ActiveSync.
2. copy JumpSPL1.56-KAIS.exe to the directory that it opens up to. Mine says "Mobile Device". That will be your "My Documents" directory on your Tilt.
3. use file explorer on Tilt to navigate to "My Documents" directory. Keep hitting "up" till you cant go any farther. The directory should be there.
4. Open "My Documents" and run JumpSPL1.56-KAIS.exe
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable.
7. run KaiserCustomRUU.exe from the flash-hardSPL directory on your laptop. Tilt will reset.
8. flash rom.

[Geraldous]

Hello,

You mentioned in step number 4: Open "My Documents" and run JumpSPL1.56-KAIS.exe

Do I run it on my tilt, using the touchscreen, or do I run it on my computer IN the mobile decices - my documents folder?

[requistp]

I tried these steps. I got to the tricolor screen. It says KAIS1*0 , SPL-1.56.Jump , CPLD-8 and USB at the bottom. When I run KaiserCustomRUU, the first program that runs jumps flashes something on my computer screen very fast and then it starts the Phone Rom update utility. My phone has not reset to this point and I don't have an activesync connection which is what this step needs. If I soft reset my phone, let activesync connect, and run the ROM update, it changes to the white screen, and goes from 0 to 100% very fast. The ROM does not update. Thanks for any help

[jockyw2001]

I tried these steps. I got to the tricolor screen. It says KAIS1*0 , SPL-1.56.Jump , CPLD-8 and USB at the bottom. When I run KaiserCustomRUU, the first program that runs jumps flashes something on my computer screen very fast and then it starts the Phone Rom update utility. My phone has not reset to this point and I don't have an activesync connection which is what this step needs. If I soft reset my phone, let activesync connect, and run the ROM update, it changes to the white screen, and goes from 0 to 100% very fast. The ROM does not update. Thanks for any help
Well it sounds all perfect. You probably now run hardSPL (press camera and do soft reset to check it) and can start to flash ROMs.

[lowreeds]

Hello,

You mentioned in step number 4: Open "My Documents" and run JumpSPL1.56-KAIS.exe

Do I run it on my tilt, using the touchscreen, or do I run it on my computer IN the mobile decices - my documents folder?

run on tilt.

[requistp]

Well it sounds all perfect. You probably now run hardSPL (press camera and do soft reset to check it) and can start to flash ROMs.

Although I did all this with the SIM card removed. When I insert it, it says "SIM card is missing." When I press camera and soft reset, I get: KAIS1*0 MFG , SPL-1.0.OliPof , CPLD-8. Is this correct?

[jockyw2001]

Although I did all this with the SIM card removed. When I insert it, it says "SIM card is missing." When I press camera and soft reset, I get: KAIS1*0 MFG , SPL-1.0.OliPof , CPLD-8. Is this correct?
Mission completed, you managed to install the hard-SPL.
You can now flash any ROM :)

Remove and reinsert the battery and start the phone again, all should be fine.
If u still get the missing SIM message try another SIM.

[jslatone]

Mission completed, you managed to install the hard-SPL.
You can now flash any ROM :)

Remove and reinsert the battery and start the phone again, all should be fine.
If u still get the missing SIM message try another SIM.

So when soft reset gives 4-color screen with the following:
KAIS1*0 MFG , SPL-1.0.OliPof , CPLD-8
its confirms hard-SPL installed?

[dayofpain]

when using file explorer click "menu" and be sure "show all files" is checked.

Happy new year!

where is this menu?

i just been looking for it, but that would explain everything im having trouble with.

[lowreeds]

where is this menu?

i just been looking for it, but that would explain everything im having trouble with.
when you run explorer on your kaiser the menu button is on the lower right of the screen.

[weddellkw]

sorry guys. my step-by-step was wrong at step #6 & 7 which i've corrected.

try this...

1. power down your Tilt and remove sd card and sim card
2. connect Tilt to laptop via USB cable.
1. open "Mobile Device" folder via "Explore" button on ActiveSync.
2. copy JumpSPL1.56-KAIS.exe to the directory that it opens up to. Mine says "Mobile Device". That will be your "My Documents" directory on your Tilt.
3. use file explorer on Tilt to navigate to "My Documents" directory. Keep hitting "up" till you cant go any farther. The directory should be there.
4. Open "My Documents" and run JumpSPL1.56-KAIS.exe
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable.
7. run KaiserCustomRUU.exe from the flash-hardSPL directory on your laptop. Tilt will reset.
8. flash rom.

When following these instructions I am unable to complete the "KaiserCustomRUU.exe" program. After hitting 'Next' twice the program says "Verifying the information on your PDA phone...please wait", which is followed by "Error [240] : File Open", "The Update Utility can not open the requested file. Please check your Update Utility." and I am left only w/ the option to Quit. A soft-reset returns my Tilt to normal...

Please help if you have any suggestions.

[lowreeds]

When following these instructions I am unable to complete the "KaiserCustomRUU.exe" program. After hitting 'Next' twice the program says "Verifying the information on your PDA phone...please wait", which is followed by "Error [240] : File Open", "The Update Utility can not open the requested file. Please check your Update Utility." and I am left only w/ the option to Quit. A soft-reset returns my Tilt to normal...

Please help if you have any suggestions.
After completing step 5 what does your boot screen say?

[max_boost]

Awesome. I used this to flash Dutty's newest rom last night and it worked without out any issues. Thanks a lot.

[MikeLim]

For those who cannot install the HardSPL and don't wonna read this thread (http://forum.xda-developers.com/showthread.php?t=349476), here is the solution:

- download the 3 attached files
- REMOVE SIM and SD CARDS !!
- copy JumpSPL1.56-KAIS.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you want to see if this works you can flash a Splash screen by running KaiserCustomRUU.exe from flash-splash.zip on your PC
- if you want to flash a hardSPL then run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC

This works for 1.56/1.57 Kaiser/TILT but not for 1.82. I started a new thread here [URL="http://forum.xda-developers.com/showthread.php?t=355910"]. I may have one of only a few 1.82's out in the wild, but I won't be the last since this is the most recent version that HTC has started shipping to the market.

Please come join me in this thread... because misery loves company - or so the saying goes ;)

Michael

[MikeLim]

For those who cannot install the HardSPL and don't wonna read this thread (http://forum.xda-developers.com/showthread.php?t=349476), here is the solution:

- download the 3 attached files
- REMOVE SIM and SD CARDS !!
- copy JumpSPL1.56-KAIS.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you want to see if this works you can flash a Splash screen by running KaiserCustomRUU.exe from flash-splash.zip on your PC
- if you want to flash a hardSPL then run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC

This works for 1.56/1.57 Kaiser/TILT but not for 1.82. I started a new thead here (http://forum.xda-developers.com/showthread.php?t=355910). I may have one of only a few 1.82's out in the wild, but I won't be the last since this is the most recent version that HTC has started shipping to the market.

Please come join me in this thread... because misery loves company - or so the saying goes ;)

Michael

[cucchiarellid]

Hi dear,
during the installationof HARDSP on my new Tilt, the PDA doesn't go in Bootloader mode (3 colors screen) but stop it in a white screen......and I can only make a soft reset to continue to use it.
I have read something about these new version of Kaiser but I need to reflash my Tilt.
Is there someone who know the way to resolve this problem?

Thanks and regards
Daniele

[wfojas]

After completing step 5 what does your boot screen say?
I get the same thing too, with a slight wrinkle. I was able to load the new splash screen,(which one tests by resetting the phone and proceeded to do the flash-hardspl. I get the tricolor screen, pull out the USB cable, hear the usb disconnect tone, put it back in, hear the usb connect tone, but Microsoft Active Sync shows not connected. So when I run the KaisercustomRUU.exe, I go through the 2 next, the get the
Error (240) File open, which I guess indicates it cant get to the device?

In my case the boot screen sez KAIS1*0 SPL-1.56.Jump CPLD-8.

That makes 2 of us?

[wfojas]

I get the same thing too, with a slight wrinkle. I was able to load the new splash screen,(which one tests by resetting the phone and proceeded to do the flash-hardspl. I get the tricolor screen, pull out the USB cable, hear the usb disconnect tone, put it back in, hear the usb connect tone, but Microsoft Active Sync shows not connected. So when I run the KaisercustomRUU.exe, I go through the 2 next, the get the
Error (240) File open, which I guess indicates it cant get to the device?

In my case the boot screen sez KAIS1*0 SPL-1.56.Jump CPLD-8.

That makes 2 of us?
Okay. I tried again this morning. What I didnt realize was once you had run jumpspl1.56-KAIS that it will now go on initialization mode on its own when you run a flash-????. So I tried to flash the test only screen again with Active sync showing it connected, and it goes through all the way until the status bar at the phone and times out at 0%, indicating that the USB is not recognized again, even after the sound chimes. Sorry for being a lazy noob, and I really think this website is the bomb, but am I missing something so that when I reinsert the USB, it doesnt recognize it again in active synch (which I think is the root of my evils, right now)? Point me to a link, oh learned ones.

[traderj]

- download the 3 attached files
- REMOVE SIM and SD CARDS !!
- copy JumpSPL1.56-KAIS.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you want to see if this works you can flash a Splash screen by running KaiserCustomRUU.exe from flash-splash.zip on your PC
- if you want to flash a hardSPL then run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC

1. Done
2. Done
3. Done
4. Ok
5. Ok

Nothing will flash after getting to the above point. Now maybe I am way out in left field here but can it be because my original ROM is a 1.81.xxx version? I can take any 1.81 version out there and flash it fine but I can't get this or the HardSPL to load no matter what I do, same thing every time.. gets to the last screen before the flash is set to start and gives a connection time out error.

Thoughts? Anybody?

[zhanghaifeng]

thanks, will have to try it once i get back home..!;)

[spenfunk]

Was a white screener...went the JumpSPL route...

Locate, run from Kaiser, tri screen with USB and grey Sync...

Remove USB, plug back in...soft rest with camera, power, and stylus, but still showingL

Kais1*0
SPL-1.56.0000
CPLD-8

Unable to install any ROM's after this...they sit at 0%...not matter what RUU or version of Dutty's I'm trying...

Sorry for the noob questions, but this is frustrating. I want to start hooking this bad boy up and playing with it...

Any and all help would be appreciated...requistp, it looks like you made it to the next step...how'd you do it, anyone?

Thanks,
Spencer

[jockyw2001]

...soft rest with camera, power, and stylus, ...
Who said that? Don't reset it when the SSPL is running, just start flashing.

[bousquet]

Thanks a millions for the fix!! When I was just getting the white screen, I thought I was going crazy with everyone else HardSPL'ing and Tri-color'ing everywhere!

Cheers m8!!

[eidetico1]

Greetings...and thanks for all the hard work.

As a preliminary: I am a stone-cold neophyte at this, so forgive my dumb questions in advance!

I held off reflashing my at&t tilt until the 1.57 issue was solved with HardSPL. Yesterday, I tried to flash my first cooked ROM. Installed HardSPL, worked fine. Then tried to flash dutty's new years rom (2k8 fixed), the device rebooted and displayed progress bar. After reaching 100%, the device rebooted again, but hung at the AT&T splash screen. Radio/Display drivers show up, but the damn thing just sits there displaying the logo.

Tried taking out the battery, soft resetting, and nothing. I can still access the bootloader, which looks proper:

KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8

And I can access the device on MTTY. Oddly, though, when I run Info 0 / Info 2 commands, I get jibberish rather than complete numbers:

Cmd>info 0
Platform Model ID:KAIS1*000
Platform HW Board ID:31, PVT1

Cmd>info 2
HTCS00000000jR*¥HTCE
Cmd>

I have tried flashing other roms, too...to no avail. It always progresses to 100%, reboots, and sits at the logo screen.

Please tell me i have not bricked my device!!! Please please please!!

Thanks much in advance for all the help.

[jockyw2001]

Looks like a prob with the cooked ROM you flashed.
Well, you have got HardSPL installed so you can flash any other ROM.

[eidetico1]

I've actually tried many different roms - dutty's lite no7, his 2k8, the att stock (cingular WWE)...nothing. same hang on the splash screen.

I can still get into the bootloader, but can't get beyond the splash.

I've tried turning off my AV/firewall when loading RUU. still nothing.



p.s. you are the man.

[mr_nonshalant]

i follow all the steps i get the tri color and the it just freezes, i can olnly get as far as the 0% line and then it just freezes< please solve this you guys are smart

[petervbeck]

i'm a non-admin on my home computer and i noticed flashing roms does not work (no sw-firewall or blocking anti-virus),
i have to login with admin permissions for flashing, maybe this can help you also...
cheers

[Deo]

I was getting the white screen too and tried this method and succeed in changing the at&t screen but when I tried hardspl it just hangs up on 0% can some one guide me what i am doing wrong !! I tried to update from other roms but just hangs up at 0% ??? :( :confused:

kais1*0
spl-1.93.0000
cpld-8

[peterkiser]

Hi,

I did follow the procedure. However it didn't take 10 min, it took less than 1 min ... How can I verify if actuaclly HardSPL did installed properly ?
PK

[etrigan]

Hello All,

My Tilt is the first device I have tried any flashing - or any modifying for that matter - on and of course I got the WSOD while running hard spl. Fortunately, I found this thread before hand so I did not panic...much.

This workaround worked like a champ!

So, for my first post I would like to say, "Thanks so much for the work you put into this".

[stoo1701]

Hi Guys, Just a THANK YOU ! for this info, I just got Orange Kaiser, and had white screen, followed instructions and presto ! back onto desktop, took aboot a minute.. Cheers guys !

[lowreeds]

Hi,

I did follow the procedure. However it didn't take 10 min, it took less than 1 min ... How can I verify if actuaclly HardSPL did installed properly ?
PK

flashing hard-spl is very quick.
much faster than flashing entire rom.

[peterkiser]

Thank You,

At the camera button /soft button boot - tricolor screen, I got:
SPL: 1.0.OliPof
Think I got it done properly.

You guys are just amazing here, really appreciate your contribution.
Thanks

[kevinniven]

when i remove my sim card the phone shuts down after 10sec!
any ideas? thanks for the help.

[gr@z!]

1- download the 3 attached files
2- REMOVE SIM and SD CARDS !!
3- copy JumpSPL1.56-KAIS.exe to your device and run it
4- after a few seconds "USB" appears on the display
5- unplug and replug the usb cable
6- if you want to see if this works you can flash a Splash screen by running KaiserCustomRUU.exe from flash-splash.zip on your PC
7- if you want to flash a hardSPL then run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC

OK, here we go..
Last week I bought the AT&T Tilt.
I preferred it instead to buy an iPhone and I'm very very very happy of my choice!!!!
A matter of seconds and I was here trying to flashing something.

I was getting the white screen too and tried the method of this Thread and succeed BUT I followed from 1 to 5.
Then I 've flashed straightly the Dutty's v3.

OK!!!! till here everything goes smootly and I'm using my Tilt with the Dutty's v3 without any problem.

The problems arise just today (this morning) when I tried to flash JUST a splash screen. NO WAY.
The process remains to 0% and that's it.

After removing/reinserting the battery and then restarting the Tilt, It restart without any problem just as it has been before this try out.

So.. curious I tried to flashing other stuff.. and NO WAY.

Always the process of flashing ANYTHING (not only splashes screen but also other ROMs) remain to 0%.

What's happening to my Tilt?
I'd have the wish to just flash a new Spash screen, but I noticed I cannot flash NOTHING at all, no more.

When in tricolor mode I have:

KAIS 1*0
SPL-1.56.0000
CPLD-8

The actual other versions of the remaing infos are in my Sign.

[gr@z!]

Oh.. I wanna add that I also tried to flash the hardSPL (kaiser-HardSPLv1) and nothing done.
How can I escape from this situation?
Someone can help me?

PS:
BTW as we speak my Tilt works perfectly.

But....

:(

[gr@z!]

OK. No responses.. :(

My Tilt, as we speak, works without any problem.. and it has the Dutty's DualTouch v3.

But I cannot flash anything else.. neither a simple splash screen.. nothing at all.

Then let's change the question..

In bootloader mode when in tricolor I read:

KAIS 1*0
SPL-1.56.0000
CPLD-8

I've tried to flash the kaiser-HardSPLv1 but the process remains at 0%.

I tried also different methods to flash the hardSPLv1 (by OliPof) but my Tilt does not flash anything.

How can I resolve this "problem"?

[oc_rydah]

HI everyone. I managed to get the HARDSPL on my Tilt. So in order for me to put a different ROM, do I just put the file on my TILT and execute there? Please help. THANKS IN ADVAVNCE.

[gr@z!]

ok..
I continue explaining my case.

As unpacked my Tilt was with this original rom:
1.57.502.2 (radio 1.27.12.11) (http://forum.xda-developers.com/showthread.php?t=329506)

And the reason because I wrote in my sign the hardware code 181007(RC01)/US , it's because, as I read, is "infamous" for the white screen problem.
For this reason I used the jumpSPL method in that post. But reading between the lines, who tried that method should have in tricolor boot SPL-1.56.Jump and not SPL-1.56.0000. Instead, flashing the regular hardSPL should be SPL-1.0.OliPof.

In my opinion I cannot flash splash screens and anything else because my SPL is "not exacly perfect".
By the way.. here the Tilt works perfectly and today I installed Tom Tom 6 too and works!

I read that other people have my same issue trying to flashing something and having the process blocked to 0% with no result.
The difference between me and them is that I was ok flashing the Dutty's v3 Rom.

I'm curious about I cannot flash anymore... just because...
and IF I WANNA FLASH the next Dutty release? :/
Am I obbliged to remain with this ROM lifetime? LOL

For this reason I wanna flash the regular hardSPL just like any other person in here ( SPL-1.0.OliPof )

What I can do to flash the hardSPLv1 with this my problem?

I read so many thread in the forum and I noticed how many different cases stories there are :/

Thank you very much in advance for any help.

EDIT:
Oh.. I have to add these other infos of my Tilt I actually have (after dutty's DC v3):

at startup in the first splash it visualize:

R: 1.27.12.11
G: 22.45.88.07H
D: 1.66.00.00

[noyz]

Wow, this sucks really bad. I was really looking forward to having a regulr Kaiser home screen and custom splash but now i'm stuck with this "NOT FOR SALE TEST ONLY" splash after doing the jump spl and then doing the "test" flash. Now whenever I try to flash a ROM or splashscreen I get the Error [262] message and have to pop out my battery. I always get stuck at 0% when trying to flash anything. I can't even go back to the way it was before. This really sucks. :(

[delta-101]

I see you managed to flash the "Test" splash, well follow the EXACT procedure you did for that AGAIN, except this time flash flash-hardSPL.zip instead of flash-splash.zip..Remember, you need to run jumpSPL on device again in order to flash hardSPL.

[noyz]

I'm giving that a try now.

[noyz]

Ok, so now I'm stuck at the Tri-Color screen after replugging in the USB cable. Nothing has happened.

KAIS1*0
SPL-1.56.Jump
CPLD-8

EDIT: I plugged and unplugged numerous times, and then I gave up and hard resetted and it still gives me that hideous AT&T splash with "TEST ONLY, etc"

[jockyw2001]

Ok, so now I'm stuck at the Tri-Color screen after replugging in the USB cable. Nothing has happened.

KAIS1*0
SPL-1.56.Jump
CPLD-8

And while in that state you only have to flash HardSPL. That's all buddy.

[paliopolis]

Mine was also a white screen, so went this route.

It died the first time and did nothing after i re-connected the USB, and gave me option to recover the device, which i followed and tried it again and voila, I see those magic pof alphabets in my bootloader.

Now cant wait for Dutty to release the v4 tonight/tomorrow :-)

[Nino18T]

For those who cannot install the HardSPL and don't wonna read this thread (http://forum.xda-developers.com/showthread.php?t=349476), here is the solution:

- download the 3 attached files
- REMOVE SIM and SD CARDS !!
- copy JumpSPL1.56-KAIS.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you want to see if this works you can flash a Splash screen by running KaiserCustomRUU.exe from flash-splash.zip on your PC
- if you want to flash a hardSPL then run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC

tried this on my Tilt. Seemed to load ok on the phone, but then phone locked up, remaining on the tri-color screen. Had to reset by removing battery. Tried loading HardSPL, figuring JumpSPL loaded ok. To no avail....errors popped up indicating prun.exe and another executable file was not available to run internally or externally. I am running Windows Vista 32-bit. Any thoughts would prove helpful.

[c.b]

OK. No responses.. :(

My Tilt, as we speak, works without any problem.. and it has the Dutty's DualTouch v3.

But I cannot flash anything else.. neither a simple splash screen.. nothing at all.

Then let's change the question..

In bootloader mode when in tricolor I read:

KAIS 1*0
SPL-1.56.0000
CPLD-8

I've tried to flash the kaiser-HardSPLv1 but the process remains at 0%.

I tried also different methods to flash the hardSPLv1 (by OliPof) but my Tilt does not flash anything.

How can I resolve this "problem"?

I have this EXACT same problem. I upgraded to Dutty's V3 with no probs after using Jumpspl. When trying to install Dutty's V4 RTM or even hardspl from the first page of this thread I sit at 0%.

Have tried this process using Vista and XP machines but still the problem exists. Does anyone have any ideas please. AS good as Dutty's V3 is I was kinda hoping to see ver 4 :-)

For what it is worth I am using a UK Orange TYTN II.

[rzanology]

heres what wored for me. Hard reset the factory att rom....and reset the device before it started installing the extended rom and apps. after the reset...i followed the instructions on post one. all is well.

[c.b]

I end up with the vendor id problem when trying that option rzanology.

Upon entering the bootloader 1 get 1.81.0000 so I re run jump spl which appears on the tricolour screen, then when trying to flash hardpsl it just sits at 0%

EDIT: I now have it working and will post up how I got it to work later on when I get more time.

[infamuz]

i need help i wus just doing the SPL and
its stuck on its main screen and its not goin anywhere..
can anyone solve this..??

[Praygo]

Dont know if im missing a step or just confused. I have an AT&T Tilt...

I would like to flash my rom. I got the white screen of death when trying to run Hard-SPL. Trying this work around. I run JumpSPL from my device and get tri color screen. I then unplug and replug USB. Active synce doesnt come back on. Is it done? I thought avtive synce was supposed to come back on.? Does hard-spl still have to be run after jump spl?

[lijo11]

'I,m stuck on the 3 colour screen Try as I might Activesync won't recognise the phone. When going through the recovery process on Kaiser Custom RUU it says its recovered but then when trying to go through the update it sticks on 0% and then says there are communication problems etc.

On the tricloloured screen it says

KAIS130
SPL-1.81.0000
CPLD-8

Can't hard reset either.

Any help much appreciated.

[shassouneh]

For those who cannot install the HardSPL and don't wonna read this thread (http://forum.xda-developers.com/showthread.php?t=349476), here is the solution:

- download the 3 attached files
- REMOVE SIM and SD CARDS !!
- copy JumpSPL1.56-KAIS.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you want to see if this works you can flash a Splash screen by running KaiserCustomRUU.exe from flash-splash.zip on your PC
- if you want to flash a hardSPL then run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC

Tried Everything, and followed directions EXACTLY.

Finally managed to get to the bootloader by using JumpSPL1.56-4.exe (and also holding down Camera key while booting).

Unplugging the USb cable then re-plugging causes activesync to lose a connection (obviously).

So now I'm stuck at the tri-band bootloader screen, and the KaiserCustomRUU.exe fails with a 260 Connection error (since it cannot "verify information on the PDA") obviously since we unplugged the USb cable.

I've had the best luck with rebooting to the bootloader BUT NOT unplugging the USb cable. Once I run the KaiserCustomRUU.exe however, it loses the activesync connection.

HELP! I need to flash hardSPL (so I can SIM unlock). This is one of the steps necessary (hard-SPLing) in order to flash an updated radio rom.

NOTE:

Kaiser bought today (Wednesday Jan 23rd 2008)
Manufacture Date:
Radio 1.27.12.11
AT&T stock ROM
KAIS1*0
SPL-1.56.Jump (this is provided I use the .exe mentioned above)
SPLD-8
USB

Help?

[thesameguy]

Tried Everything, and followed directions EXACTLY.

Finally managed to get to the bootloader by using JumpSPL1.56-4.exe (and also holding down Camera key while booting).

Unplugging the USb cable then re-plugging causes activesync to lose a connection (obviously).

So now I'm stuck at the tri-band bootloader screen, and the KaiserCustomRUU.exe fails with a 260 Connection error (since it cannot "verify information on the PDA") obviously since we unplugged the USb cable.

I've had the best luck with rebooting to the bootloader BUT NOT unplugging the USb cable. Once I run the KaiserCustomRUU.exe however, it loses the activesync connection.

HELP! I need to flash hardSPL (so I can SIM unlock). This is one of the steps necessary (hard-SPLing) in order to flash an updated radio rom.

NOTE:

Kaiser bought today (Wednesday Jan 23rd 2008)
Manufacture Date:
Radio 1.27.12.11
AT&T stock ROM
KAIS1*0
SPL-1.56.Jump (this is provided I use the .exe mentioned above)
SPLD-8
USB

Help?

Same problem...

I've flashed two other Tilts with the factory HTC ROM without issue... Bought a third Tilt today (24 Jan 08) and originally got the White Screen. Stuck JumpSPL on the phone, ran it, restarted to the Tri Color Screen with 'USB' displayed at the bottom. ActiveSync is green until I unplug the USB cable - it goes grey/disconnected and will not reconnect. Same screen as shassouneh.

Hmmm....

[wfojas]

I end up with the vendor id problem when trying that option rzanology.

Upon entering the bootloader 1 get 1.81.0000 so I re run jump spl which appears on the tricolour screen, then when trying to flash hardpsl it just sits at 0%

EDIT: I now have it working and will post up how I got it to work later on when I get more time.

Yeah, that would be cool. I've had this problem for a few days now, and I really just needed to change the splash back to the standard AT&T one to send it back for exchange, as the radio doesnt work now. Thanks in advance for your input, it would really be appreciated.

[drokkon]

Just call me Murphy.

Tilt 1 died due to a RLoD. Tilt 2 wouldn't make/receive calls. Tilt 3 had a loose USB port. Tilt 4 had cosmetic damage. Tilt 5 was the magical "no lemon policy" NEW phone.

Hungry for Dutty's newest ROM, I quickly HardSPLed to a ... white screen! Luckily I frequent the forum and remembered this sticky. Not even sure what was wrong with my phone, and not even sure I care.

Your thread fixed my problem easy as can be.

Thank you!!!

PS - Should I care? Is the white screen a symptom of something I should know about?

[Red_Toyol]

Hi there,

I just bought a new TyTNII yesterday, tried to HardSPL using Kaiser Hard-SPL v1 but stuck at white screen. So I tried the steps suggested by jockyw2001. Running JumpSPL1.56-KAIS.exe, I got USB on the display. Everything seems fine until this step. But then, when I unplug the USB cable (ActiveSync grey), and replug again, I cannot establish Activesync anymore. Tried 5 times, same result. I am running Vista Ultimate.

Any help people?

-Red-


- download the 3 attached files
- REMOVE SIM and SD CARDS !!
- copy JumpSPL1.56-KAIS.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you want to see if this works you can flash a Splash screen by running KaiserCustomRUU.exe from flash-splash.zip on your PC
- if you want to flash a hardSPL then run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC


Edit: Solution

1. After you run JumpSPL1.56-KAIS.exe, you will get the Rainbow screen on your device with "USB" appears on it
2. Unplug and replug. IMPORTANT: The activeSync will not establish. So what you need to do is to make sure the USB is connected. How? Open your PC/Laptop's Windows Device Manager. In Vista, you should find "Mobile Device" in the device list. In XP, if not mistaken, you should get something like "Windows Mobile". This shows that USB connection to your Kaiser is working (although ActiveSync not sync).
3. Run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC, then follow instructions. Your Kaiser will reboot after this completed.
4. Just to make sure things are all okay, hold power+camera+reset and check the BootLoader screen, if successful you should see "SPL-1.0.OliPof" in the second line. Soft reset.

[E-ducation]

@jockyw2001

help needed

i made a mistake while installing HardSPL,in fact i`ve skipped a whole step as i was trying to unlock with your Sim Unlocker.after starting the JumpSPL1.56-KAIS.exe on my MDA Vario 3 I`ve forgot to install HardSPL:( (yes,RTFM,but now the damage has been done).after that I`ve flashed with your modified ROM for unlocking and it stopped at 95%.The phone displays:
RUUNBH
KAIS130
SPL-1.94.0000
CPLD-8


I can`t find the original ROM on net since my phone is from a small country(Montenegro).I`ve tried to boot from MTTY,but it says Command error!!
task 8 doesn`t work either,it just reboots the phone to tri-color screen again.Hard reset doesn`t work.The phone is still CID locked since it can§t be flashed with any ROM I could find

Cmd> info 0
Platform Model ID:KAIS13000
Platform HW Board ID:31, PVT1



and with the other command:

Cmd>info 0
Platform Model ID:KAIS13000
Platform HW Board ID:31, PVT1

Cmd>info 2
HTCST-MOB012^PŸ
HTCE
Cmd>getdevinfo
GetDevInfo: Get CID OK

HTCSKAIS1300TMB1HTCE


as you see,it`s a TMB1 CID. can you send me the file or link for a file with the same CID????

THX in advance!!Any help is apreciated!!

[jockyw2001]

@jockyw2001

help needed

i made a mistake while installing HardSPL,in fact i`ve skipped a whole step as i was trying to unlock with your Sim Unlocker.after starting the JumpSPL1.56-KAIS.exe on my MDA Vario 3 I`ve forgot to install HardSPL:( (yes,RTFM,but now the damage has been done).after that I`ve flashed with your modified ROM for unlocking and it stopped at 95%.The phone displays:
RUUNBH
KAIS130
SPL-1.94.0000
CPLD-8


I can`t find the original ROM on net since my phone is from a small country(Montenegro).I`ve tried to boot from MTTY,but it says Command error!!
task 8 doesn`t work either,it just reboots the phone to tri-color screen again.Hard reset doesn`t work.The phone is still CID locked since it can§t be flashed with any ROM I could find

Cmd> info 0
Platform Model ID:KAIS13000
Platform HW Board ID:31, PVT1



and with the other command:

Cmd>info 0
Platform Model ID:KAIS13000
Platform HW Board ID:31, PVT1

Cmd>info 2
HTCST-MOB012^PŸ
HTCE
Cmd>getdevinfo
GetDevInfo: Get CID OK

HTCSKAIS1300TMB1HTCE


as you see,it`s a TMB1 CID. can you send me the file or link for a file with the same CID????

THX in advance!!Any help is apreciated!!

If HardSPL is not installed you must flash an official RUU which matches your Vario3 CID and ModelID:
CID=T-MOB012
ModelID=KAIS13000

As there are many who suffer from this problem I am tempted to find a solution, but since HardSPL is not installed there is only some task commands to play with so there is not much hope. You better start trying to find the RUU.

[E-ducation]

i know but till now i had no sucess in finding a official Vario 3 RUU,only AT&T or HTC....

anyone has a recomposed dumped ROM for VARIO 3?

THX in advance

[jockyw2001]

i know but till now i had no sucess in finding a official Vario 3 RUU,only AT&T or HTC....

anyone has a recomposed dumped ROM for VARIO 3?

That will not help you, because dumped and reconstructed ROMs are unsigned and can only be flashed with HardSPL.
You need an original full RUU.

[E-ducation]

That will not help you, because dumped and reconstructed ROMs are unsigned and can only be flashed with HardSPL.
You need an original full RUU.


and nof i`m realy in trouble!!!!:(

any idea where to find such a ROM?

[lijo11]

If it's of any assistance in trying to find a solution to this problem of failing to install HardSPL then I have noticed the following:

Having got to the update page in the RUU programme prior to HardSPL being flashed the RUU fails to recognise my Orange SPL of 1.81 etc and the current image details section of the page is blank.

When I try the same procedure with the RUU to flash the original Orange ROM it recognises the current version and displays the full details on the relevant page.

Could it be possible that the Orange ROM has some protection inbuilt which is preventing the HardSPL being flashed? I've seen a post elsewhere which suggests that it is NOT possible to flash HardSPL onto the Orange 1.81 etc phone.

Any comments?

[stoo1701]

Hi people,
Ok, after crushing my screen, (was running Dutty's Dualtouch 2k8) I got my new Kaiser today. Normal SPL, no chance, WSD. Tried the 2nd method at the top of this forum 'Solved', still no joy. I absolutely can NOT get past the tri-colour. I unplug / replug, but no activesync, and more importasntly no "Windows Mobile" usb connection. The connection sounds play, but I can't connect at all from the tri-colour screen. Reset and all is fine (except SH&%ty orange boring ass crippled rom...)

Please help...
Versions:
Operator Version 24.181.1.612
Rom Version 1.81.61.2 WWE
ROM Date 20/9/07
etc etc..

from Tri-colour :
KAIS130
SPL-1.56.Jump
CPLD-8

Not sure which is relevant here, 'scuse the noob ;)

Has anyone solved this?
(and yes I have checked the WIKI and searched :)

[delta-101]

You need to wait until pc correctly detects USB Device in Device Manager... it may need to install drivers etc.. you using XP or Vista?

[stoo1701]

You need to wait until pc correctly detects USB Device in Device Manager... it may need to install drivers etc.. you using XP or Vista?

Hi, thanks for your input. I'm running XP (got vista on dualboot but use xp for flashing etc)
This setup worked perfectly using the first post in this thread, got Dutty on my Kaiser no probs, but now I have the replacement, I just can't get it to connect after unplug/replug. I suspect its the orange rom version, but thats from last september? I just dont fecking get it..

Any sugg's would be appreciated..

[delta-101]

You could try UN-tick - Allow USB Connection in activesync & also try disabling automatic startup of activesync upon device connect..

[RocketChimp]

Hi all.

Sorry to clutter this thread with what may be another noob question, but I've searched the boards for quite some time now and haven't come across this.

Using the instructions provided in this thread and its parent, I'm able to get as far as running KaiserCustomRUU.exe. I proceed through the first prompt or two, at which point the utility scans my device:

http://i32.tinypic.com/1iikvd.jpg

After a minute or two, the app seems to recognize my device-- it does not throw any exception and takes me to the next prompt. However, the next prompt displays no info relevant to my handset:

http://i29.tinypic.com/o9lh1l.jpg

Is this typical behavior for KaiserCustomRUU, or is this a red flag? Was wary of proceeding with the update given the null display. My apologies if this has been answered previously.

Any feedback appreciated.

Thanks!

RC

[JPIndustrie]

For a variety of reasons, I'm finally on my 3rd ATT Tilt.


I tried the original HardSPL, and got the white screen. Found this thread, tried the JumpSPL on the first post (Yes, I removed my SIM/SD cards + kept it connected while I ran it on the phone) and I still got a white screen.

At the white screen, I'm able to simply soft-reset, and back to ATT Windows Mobile.

Any Ideas? I really wanna load Dutty's new ROM and it sucks because it looks like I can't. I've read through alot of posts and can find no info as to why my particular tilt cannot run either (hardSPL, or white-screen JumpSPL) and only get white screens.

I have:
ROM: 1.57.502.2
ROM DATE: 08/25/07
Radio version: 1.27.12.11
Protocol Version: 22.45.8807H

[Red_Toyol]

That is normal. I got the same, I already HardSPL.

-Red-

Hi all.

Sorry to clutter this thread with what may be another noob question, but I've searched the boards for quite some time now and haven't come across this.

Using the instructions provided in this thread and its parent, I'm able to get as far as running KaiserCustomRUU.exe. I proceed through the first prompt or two, at which point the utility scans my device:

After a minute or two, the app seems to recognize my device-- it does not throw any exception and takes me to the next prompt. However, the next prompt displays no info relevant to my handset:

Is this typical behavior for KaiserCustomRUU, or is this a red flag? Was wary of proceeding with the update given the null display. My apologies if this has been answered previously.

Any feedback appreciated.

Thanks!

RC

[Red_Toyol]

Have you really read JP? Look at my post #101, the answer is there.

-Red-

For a variety of reasons, I'm finally on my 3rd ATT Tilt.


I tried the original HardSPL, and got the white screen. Found this thread, tried the JumpSPL on the first post (Yes, I removed my SIM/SD cards + kept it connected while I ran it on the phone) and I still got a white screen.

At the white screen, I'm able to simply soft-reset, and back to ATT Windows Mobile.

Any Ideas? I really wanna load Dutty's new ROM and it sucks because it looks like I can't. I've read through alot of posts and can find no info as to why my particular tilt cannot run either (hardSPL, or white-screen JumpSPL) and only get white screens.

I have:
ROM: 1.57.502.2
ROM DATE: 08/25/07
Radio version: 1.27.12.11
Protocol Version: 22.45.8807H

[wfojas]

I tried to update the rom again, and while I am able to change the splash, nothing happens when I try to update to the hardspl. I also need to exchange my phone to AT&T as the 3d/edge part no longer works.
Does anyone know where i can get the original A T & T splash to replace the test only one?

[mark43]

Hi all.

Sorry to clutter this thread with what may be another noob question, but I've searched the boards for quite some time now and haven't come across this.

Using the instructions provided in this thread and its parent, I'm able to get as far as running KaiserCustomRUU.exe. I proceed through the first prompt or two, at which point the utility scans my device:

http://i32.tinypic.com/1iikvd.jpg

After a minute or two, the app seems to recognize my device-- it does not throw any exception and takes me to the next prompt. However, the next prompt displays no info relevant to my handset:

http://i29.tinypic.com/o9lh1l.jpg

Is this typical behavior for KaiserCustomRUU, or is this a red flag? Was wary of proceeding with the update given the null display. My apologies if this has been answered previously.

Any feedback appreciated.

Thanks!

RC

This is typical. See pic. Make sure before you proceed that it says hardspl or like before you do a rom flash. Once you do hardspl you do not need to do it again. Also the KaiserCustomRUU is the "vessel" for flashing, the actual flash is a .nbh and will be shown once you click THAT button. BTW this was the hardest step that I have experienced so far. The next time you want to flash ensure activsync is connected green, open jumpSPL from phone, disconnect usb and reconnect, run the ruu and you are done. I have been told that it is wise to do a hard reset after you flash a rom when it gets to the screen alignment (somehow washes away all ghosts from prior ROM).

Ron

[RocketChimp]

Thanks a ton for the feedback, folks.

Make sure before you proceed that it says hardspl or like before you do a rom flash.

Ron, sorry if I'm splitting hairs here, but what specifically should read HardSPL?

[JPIndustrie]

RedToyol -

Thank you for clairfying. According to JockyW, a hard reset should be performed before doing the JumpSPL. I was able to get the multi coloured screen and use flashHardSPL.

Is the Flash HardSPL identical to the original HardSPL? Am I safe to start loading ROMs? When I enter bootloader, I get "SPL-1.0.OliPof".

Thanks.

[Red_Toyol]

I have PM Jocky, asking the same question you asked me. And according to his reply, yes, we have HardSPL our Kaiser correctly. If that so, than we are ready for cooked ROMs!

-Red-

RedToyol -

Thank you for clairfying. According to JockyW, a hard reset should be performed before doing the JumpSPL. I was able to get the multi coloured screen and use flashHardSPL.

Is the Flash HardSPL identical to the original HardSPL? Am I safe to start loading ROMs? When I enter bootloader, I get "SPL-1.0.OliPof".

Thanks.

[halfchkn]

Worked here! Awesome job, as soon as I get a job, donation on it's way..

[thesameguy]

Post #101 worked for me as well... Thrilled about this - As soon as funds make their way back to my paypal, I'll send some your way! Thanks!

[AvinashDhaniraj]

THANK YOU Jocky2001! WORKS GREAT!!!

[DionRinaldi]

Could you give some advise about this problem. When I try to open or run (CMD) kaiser-simlocker, the small black window quickly opens and closes. It doesn't stay open, so I haven't been able to progress pass this point. Please let me know the solution.

[richwang]

It worked! I successfully flashed HardSPL and Chinese ROM into my AT&T Tilt that I received yeseterday!!! Thanks a lot!!!

[look9001]

Hmmm... I must be doing something wrong.

I copy JumpSPL1.56-KAIS.exe to my device, find it in file explorer, run it, but then just get a white screen. Nothing else happens. Any suggestions? This is the T mobile vario iii flavour kaiser.

[ronin2ppc]

Thank you everyone for making my life worth living. I love this stuff.:D

[modert]

Thanks everyone that suggested post #101 it finally worked for me....I was about to give up but I will continue on now!!!!

[shassouneh]

Never mind, got it working. Thanx!

[jgdorado]

(removed to eliminate confusion)

[deymayor]

And while in that state you only have to flash HardSPL. That's all buddy.

i think you saved the whole Tilting world with this post. Now flashing Alex's ROM so good luck to me, 49% complete so far.

[ssaibal]

I copied the JumpSPL file to my AT&T Tilt phone (8925) and then executed the program and got the tri-color display. Connected the USB cable and then ran the KaiserCustomRUU to start flashing the device. It went upto 95% mark and then it gave the error 262 and asked me to go thru the recovery process. I have been thru that process many times now, but it keeps coming back to the tri-color screen every time I reconnect the battery and power the device up.

Please suggest what I should do to recover from this.

[Renvall]

:)



I Was Becoming Very Frustrated That I Could'nt Flash My ROMs,

I owe you so much thanks,

if i was old enough or had the means,

i would definitely send u a donation,

thank you again :)

[ssaibal]

I read thru many threads on how to unlock the SIM and also noted that installing HardSPL is necessary to avoid bricking the phone. So, I went to the thread where the solution to the error 262 (white screen) is provided. I downloaded the files from the 1st post in that thread and then copied the JumpSPL1.56-KAIS.exe to the phone and then executed it. It got me the tri-color screen (Is this called bootloader?) and then I executed the KaiserCustomRUU.exe from the flash-HardSPL.zip thinking that this will put in the HardSPL into the ROM. The progress bar went upto 95% and then it exited with error and after that the "Recovery" option of the loader hasn't been able to revive the phone. Every time, I put the battery back in and power it up, I get the tri-color screen with the following message:

RUUNBH (on the top right hand side of the screen)
KAIS1*0
SPL-1.56.0000
CPLD-8

Please guide me with what I should do next to recover. I have ten different threads open here in my browser and I am trying to understand the stuff, but I am not able to understand what I should do next. I remember my original Radio was 1.27.12.11 (I saw this message when the phone used to boot up) and it is a 3 day old phone from AT&T here in California.

I recently replaced my 2 year old Cingular 8125 which I had unlocked myself following this forum 2 years back. But, this time I must have done something incredibly stupid. Appreciate any help.

[jockyw2001]

But, this time I must have done something incredibly stupid. Appreciate any help.
That's right, you should have flashed HardSPL first.

To resolve your issue try this:
- in activesync uncheck "allow USB connections"
- connect to your phone with MTTY
- press return twice until you see "Cmd>"
- type "boot"
- wait until the device restarts and exit MTTY
- if it enters the bootloader screen again try the previous 2 steps again

[cucchiarellid]

Hi Jockyw001 at to all friends,
news about to install Hardspl on the new version of Tilt, like 1.81, 1.93 ecc?
I really thanks to the job of all yours..

Thanks and regards
Daniele

[nstefanelli]

great solution. much appreciated

[smonte]

That's right, you should have flashed HardSPL first.

To resolve your issue try this:
- in activesync uncheck "allow USB connections"
- connect to your phone with MTTY
- press return twice until you see "Cmd>"
- type "boot"
- wait until the device restarts and exit MTTY
- if it enters the bootloader screen again try the previous 2 steps again

jockyw2001 many many thanks. My device came back to life. This worked, I had to do it twice, after that I flashed it with SSPL and with HardSPL and now everything works fine, just like before.

[look9001]

Hmmm... I must be doing something wrong.

I copy JumpSPL1.56-KAIS.exe to my device, find it in file explorer, run it, but then just get a white screen. Nothing else happens. Any suggestions? This is the T mobile vario iii flavour kaiser.

Can someone please help with this? I'm confident I followed the instructions correctly but as soon as I run JumpSPL1.56-KAIS.exe, white screen, and nothing more.

When I boot the phone the numbers I see are:

1.27.12.32
22.45.88.07H
1.56.00.00

Any clue anyone? It seems that for everyone else this problem is fixed by this version of JumpSPL apart from me :(

[derHarry]

Hello out there,

i'm triying to get a new splash screen, copied the JumpSPL1.56-KAIS.exe to the kaiser, ran it when it enters the bootloader and says usb, un/replug the usb BUT then nothing happens... after that i made a softreset, starting the device newand tried to flash a new splash screen with the KaiserCustomRUU.exe form the flash-hardSPL zip. The result is a 262 error. :(

in bootloader the following information is given:
KAIS130
SPL-1.56.0000
CPLD-8

device is a T-Mobile Austria mda vario iii

please excuse my english, i know its horrible :rolleyes:

any suggestions would be nice, thank you,

cheers
der Harry


-----
DONE...
sorry, found the solution is 3 pages before... <(*¿*)> plz ignore my post

[Gibbs]

Thanks so much to the author of this thread, as well as to everyone who posted helpful advice here! I'm a total noob to windows mobile, as I'm just upgrading from a palm-based treo 650. Using the instructions in this thread, I was able to flash Alex's home ROM onto to my new tilt. It's fantastic compared to the ATT rom!

[copden]

i am stuck with "test only screen" and re do from beginning just flash hard spl but the screen still come up with att test only, please how do i get this out???
my phone also having " you have tried 6 times plese wait for time out..." when i try to but in unlock code, anyone know how to reset this
I have the code but the phone don't let me enter it
thanks you guy

[MrBroadway]

am i suppose to change my image version??

i dont want to downgrade to some suckie version

[chriscc01]

Hi guys,

anyone that can give me full solution will be my personal god and ill donate.

I tried flashing hard SPSL and its gone wrong.
I have a T-Mobile Vario III ( bought 8/02/08 )

I get up to the tricolour screen - with white at the bottom and this is what it says.

top left corner: RUUNBH

Right: KAIS130
SPL-1.56.0000
CPLD-8

At the bottom on the white it says 'serial' when the USB is plugged in it says USB.

Ive tried alot of things ive read now im stuck here.

please help.

C

[jockyw2001]

Try what I described here (http://forum.xda-developers.com/showpost.php?p=1894935&postcount=135), that will hopefully fix the boot problem (RUUNBH). If your device boots in Windows, make sure to install HardSPL first !!

[kainmc]

thanks a million times, my problem solved!!! :D

[MarkanthonY]

I finally figured out what I was doing wrong. After running Kaiser-hardsplv1 and hitting enter the first time, I kept getting stuck. While kaiser was connected to pc and hardslv1 was running, I copied jumpspl1.56-kais to my doc on pda. Ran it. Then went back to hardsplv1 and hit enter (i think 2X) and finally got tri-color with usb. Now my tri color screen has Kais1*0 MFG; SPL-1.0.OliPof; CPLD-8. Thank you for all your help. I get paid on Friday. I will make my donations then. :D

[henrryxd]

today is my first day on this website. and i dont have much idea wht u guys talking about.
well i do have the white screen problem. as he explains the steps of "coping the jumpspl file to the device." how do u copy it on to the device? if someone doesnt mind can u please help. thank you

[flyingchoc]

Hi!

This is my first go at flashing my ROM and I've followed the instructions on this thread and run JumpSPL and get to the tri colour screen with USB at the bottom, but when I run the ROM update utility I get stuck at step 2, which says "Establish an activesync connection"... activesync doesnt do anything and the icon is still grey. Where am I going wrong?

Neil

[flyingchoc]

Ignore the above. I *didnt* follow the instructions properly.... DOH.

[henrryxd]

can someone please help. i keep on getting the error 240 file open. i have the tri color screen i did the unconnect and reconnect. but once i try to flash spash, i keep on getting that error sorry for repeating but i looked through the whole forum i cant seem to locate where this problem was addressed. thank you

[jockyw2001]

can someone please help. i keep on getting the error 240 file open. i have the tri color screen i did the unconnect and reconnect. but once i try to flash spash, i keep on getting that error sorry for repeating but i looked through the whole forum i cant seem to locate where this problem was addressed. thank you
It looks like the splash screen can not be found. It (splash.nbh) should be in the same directory as the update utility (KaiserCustomRUU.exe)

[edbutler]

For those who cannot install the HardSPL and don't wonna read this thread (http://forum.xda-developers.com/showthread.php?t=349476), here is the solution:

- download the 3 attached files
- REMOVE SIM and SD CARDS !!
- copy JumpSPL1.56-KAIS.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you want to see if this works you can flash a Splash screen by running KaiserCustomRUU.exe from flash-splash.zip on your PC
- if you want to flash a hardSPL then run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC
I have a Tilt and I had to do things a different way, But could not do it at all if not for the help I received here, thanks to jockyw2001. I copied the jumpSPL1 to my phone and then ran the Kaiser Hard SPLv1 when it got to the point where it said you should be in boot loader mode "Tri colored screen" I wasen't if I pressed enter you know "White Screen" so I repeated the steps in Hard SPL but after the first step before I hit enter to continue I ran the file I copied to the phone "JumpSPL" then the tilt went into bootloader mode "Tri colored " then I went back to the desktop and hit enter ,unplug and replug and I was off. So I had to do it a tad different but it worked fine and I have flashed Schaps 4.31 and I might try Vega but I am used to Schaps I have always used his stuff on my 8525 so I really trust his work. Again thanks for your help. could not have done it with out you.
Ed...

[ffffffff]

... ... I repeated the steps in Hard SPL but after the first step before I hit enter to continue I ran the file I copied to the phone "JumpSPL" then the tilt went into bootloader mode "Tri colored " then I went back to the desktop and hit enter ,unplug and replug and I was off.... ...
Ed...
cOULD YOU GIVE MORE details please:
After JumpSPL and Tricolour Screen: what did you do exactly. Because if you only went back to desktop, and hit the enter, nothing would happen as it is trilolour screen and you need to authorize Hardspl to run on Kaiser, but you can not see a thing so you can not run Hardspl, can you?!!

Bdsides, after jumspl, you lost USB connection so Hardspl can not be transfer to the Kaiser anyway. I know you did it but I am confused??

[jmcorral]

Excellent Work!!!!!
You willl receive a donation very soon!!!
Thanks!!!!!

[MarkanthonY]

Ok payday is here. Thanks for the help. Donation has been made. I really appreciate all that you guys do. I am an HTC pda and xda-dev fan for life.

[simonmcmullon]

Ran Jumpspl
Ran KaiserCustomRUU.exe
at 95% I got a usb error, carred out the recovery and cant get pase 0% on flashing.

So now im stuck in the Tri Colored screen.

Help.

Cheers, Simon.

[simonmcmullon]

Ok I got past the tri clour problem with mtty. Now im stuck on the simunlock.

=== Kaiser Sim Unlocker (c)2008 by jockyw2001
=== Donations happily accepted, paypal to jocky_wilson@hotmail.com
\\.\WCEUSBSH001: No such file or directory
cannot connect to \\.\WCEUSBSH001

cheers, Simon.

[superwild5]

For those who cannot install the HardSPL and don't wonna read this thread (http://forum.xda-developers.com/showthread.php?t=349476), here is the solution:

- download the 3 attached files
- REMOVE SIM and SD CARDS !!
- copy JumpSPL1.56-KAIS.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you want to see if this works you can flash a Splash screen by running KaiserCustomRUU.exe from flash-splash.zip on your PC
- if you want to flash a hardSPL then run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC

I follow the procedure and after I run KaiserCurstomRUU.exe from flash-splash.zip, I Tilt got stuck at 0% white screen. Util on PC show connection problem. Help!...

[LeePhan79]

Hi, guys im new here and im having terrible trouble installing this HardSPL on my phone. The instrucitons arent detailed enough for me. Like I dont get how you copie the JumpSPl files onto my phone. Like where do i put it and how to i find it on my phone? I simply removed my MicroSD and SIM card from my tilt and synced it up to the PC. I download the files and I look up my device under My computer. I then unzip and drag the JUMPSPL.exe file into my device and now im stuck. Where do I go on my phoen to find the exe file and start it?

[DaveShaw]

Hi, guys im new here and im having terrible trouble installing this HardSPL on my phone. The instrucitons arent detailed enough for me. Like I dont get how you copie the JumpSPl files onto my phone. Like where do i put it and how to i find it on my phone? I simply removed my MicroSD and SIM card from my tilt and synced it up to the PC. I download the files and I look up my device under My computer. I then unzip and drag the JUMPSPL.exe file into my device and now im stuck. Where do I go on my phoen to find the exe file and start it?

You should get to know your phone a little better before trying this, but I'll help anyway.

To run the exe, use File Explorer on the phone to browse to "My Documents" on the Phone, then click it to run JumpSPL.

[CollectorTA]

Thank You, Thank You, Thank You

[Creepyone]

hi i tried installing hardspl now my usb is unreadable?/ any help

[ffffffff]

hi i tried installing hardspl now my usb is unreadable?/ any help
Have a look at this http://forum.xda-developers.com/showthread.php?t=369567

just might help

King

[batjoro7]

For those who cannot install the HardSPL and don't wonna read this thread (http://forum.xda-developers.com/showthread.php?t=349476), here is the solution:

- download the 3 attached files
- REMOVE SIM and SD CARDS !!
- copy JumpSPL1.56-KAIS.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you want to see if this works you can flash a Splash screen by running KaiserCustomRUU.exe from flash-splash.zip on your PC
- if you want to flash a hardSPL then run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC

hi, i have done all this above, is my phone cid unlocked now.?
thanks

[danilodn]

hi all,
about the tri-color screen stuck issue, i am curious to know if everybody else who is having this problem uses Vista.
i found out that when i reconnect the usb cable, Vista doesn't recognize it as the same device as before (in my case it showed "unknown device").
so, the usb driver installed before doenst work anymore, that why the update Rom software cant connect to the phone. (message 240 or 0% at update screen).
when i try to update the usb driver from the device manager it says that the Vista RUU driver doesnt work with my 32 bit system and it doesnt let me to update the driver.

we could try to install another driver for the usb tri-color screen before changing it to the Vista RUU (Xp sync driver that makes vista work with updating roms).
anybody has it?
lets try to make this work pls.

[Quilombo]

Hey guys, I'm a brand new user to the forum and have been reading to look for instructions to unlock my att tilt. I got it abt 3 days ago and flashed the latest rom (version 1.62.502.0) update from att. I tried all the steps to unlock the sim or load hardspl to no avail.
Working step 1 of these instructions and saw the tri-color screen then
The screen becomes white with a progress and stay at 0%
Active sync becomes disconnected
That white screen never goes away and on the PC i see [Error 262] and it gives me steps to recover.
I am running XP Pro SP2
Rom vers 1.62
Radio vers 1.27
I tried this flashing both sspl 1.56 and 1.16 to no avail. Any help appreciated
A hard reset did not help either

[qaiserjaved]

Hey Guys..

I have unlocked HTC Kaiser Locked to Orange UK two weeks ago but now i am having a problem. After doing HardSpl..i can see "SPL-1.0 OliPof" if i put my phone into bootloader mode. Now the problem is whenever i want to run KaiserCustomRUU, which is step 1 of sim unlocking the phone, i get the messege before actual installation starts..""Kaiser-simunlocker/step1/kaiser-radio-patched.nbh" i guess the last file is the file patched from the software. When i press ok, It give me a message of "ERROR[238]: FILE READ" "The update utility can not open the requested file. Please Check your Update Utility" I dont know what to do now. I have even took the battery off for like 5 times..restarted my phone so many times. and even tried to do flash_hardspl (One i have explained above) so many times. But i am unable to find the solution. Please help me in this regard.

I know there are some geniuses monitoring this forum. Please help me guide me with the detailed procedure.

Thanks for the previous help.

[xmoo]

I'm getting white screen while trying to HardSPL a device of my friend.

Tried HardSPL and also this method, but it did not work. Someone know how to fix it?

ROM version: 1.56.404.6
Radio version: 1.27.12.32
Protocool Version: 22.45.88.07H

[tone21705]

Hi im also having the same problem, just got a refurb tilt today actually from at&t dated 181007/(RC01)/US
R 1.27.12.11
G 22.45.88.07H
D 1.57.00.00

Using XP SP2

Ive tried the normal one (with cmd) and then the white screen problem. have to SR each time.


Thanks

[Quilombo]

One very minor but critical detail not listed was the source of all my problems. I found it by reading thru about 9-10 pages of this thread. here it goes:
- download the 3 attached files
- REMOVE SIM and SD CARDS !!
- copy JumpSPL1.56-KAIS.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you want to see if this works you can flash a Splash screen by running KaiserCustomRUU.exe from flash-splash.zip on your PC
you must run the jumpspl again on the htc/tilt before flashing hardspl for it to work. This is what solved my issues
- if you want to flash a hardSPL then run KaiserCustomRUU.exe from flash-hardSPL
Perhaps, the OP can add this to the original instructions.

[xmoo]

One very minor but critical detail not listed was the source of all my problems. I found it by reading thru about 9-10 pages of this thread. here it goes:

you must run the jumpspl again on the htc/tilt before flashing hardspl for it to work. This is what solved my issues

Perhaps, the OP can add this to the original instructions.

But when i open JumpSPL1.56-KAIS.exe i get white screen. So is it actualy working but not showing??

[mcjazz1232]

Everything works for me but I am still stuck with this screen whenever I reset my device "Test only not for sale". How can I get rid of it?

[jorfee]

once it shows the tri color screen i unplug and plug back in the usb and it does nothing. I must have taken my battery out 10 times so far.

[qaiserjaved]

Hey Guys,

I have solved the problem of HardSpL. Thts done but now when i run KaiserCustomRUU from step 1 folder, for unlocking, it pops a message "Desktop\kaiser-unlocker\step1\kaiser-radio-patched.nbh" and after when i press ok, it gives an "ERROR 238: FILE READ. The update Utility can not open the requested file. Please check your update utility".

Please some body help me. I really dont understand why i am getting this error as i have successfully done the HardSPL.

Thanks

[jorfee]

1. power down your Tilt and remove sd card and sim card
2. connect Tilt to laptop via USB cable.
1. open "Mobile Device" folder via "Explore" button on ActiveSync.
2. copy JumpSPL1.56-KAIS.exe to the directory that it opens up to. Mine says "Mobile Device". That will be your "My Documents" directory on your Tilt.
3. use file explorer on Tilt to navigate to "My Documents" directory. Keep hitting "up" till you cant go any farther. The directory should be there.
4. Open "My Documents" and run JumpSPL1.56-KAIS.exe
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable.
7. run KaiserCustomRUU.exe from the flash-hardSPL directory on your laptop. Tilt will reset.
8. flash rom.

hope this helps...

how do you do that because the activesync disconnects after u unplug the usb so when u go to hardspl flash it it says u must have an activesync connection..so then how do u get it back once its on the tricolor screen because unplugging and replugging shows no diff on it

[jorfee]

I tried these steps. I got to the tricolor screen. It says KAIS1*0 , SPL-1.56.Jump , CPLD-8 and USB at the bottom. When I run KaiserCustomRUU, the first program that runs jumps flashes something on my computer screen very fast and then it starts the Phone Rom update utility. My phone has not reset to this point and I don't have an activesync connection which is what this step needs. If I soft reset my phone, let activesync connect, and run the ROM update, it changes to the white screen, and goes from 0 to 100% very fast. The ROM does not update. Thanks for any help

Mine keeps disconnecting with the activesync then after a min i get an error message during the kaisercustomruu rom update and it never makes it past 0%

[evilgabbie]

Mine keeps disconnecting with the activesync then after a min i get an error message during the kaisercustomruu rom update and it never makes it past 0%

same here..

[mister wiggles]

can i follow the instruction from post 1 to install hardspl on a tilt (straight out of the box) or is this a help link for ONLY those who have experienced the "white screen?"

[mmalka]

*sigh.. young gun, back in my day we had to run everything ourselves, it wasn't put in a neat little package that did everything for us.

After you get into the tircolored screen and plug your USB back in, you have extract and run hard spl (using the file on the first page of this thread).
http://forum.xda-developers.com/attachment.php?attachmentid=63026&d=1198513037

That one to be exact.


Two questions:
1- I already did the CID unlock process. Does it mean I already flashed hard spl and don't need to do this?
2- Just to play safe, I tried to perform these steps. Got the tri-color screen, unplugged and plugged the USB cable. However, after plugging it back, the ActiveSyc icon stays grey and hard spl requires it to be green to run. I did a soft reset, rebooted the PC, but got the same results. What am I doing wrong?
Thanks.

Never mind: I decided to try flash the ROM, and it worked. It seems that everything was ready.

[tilt4life]

When I download the flash-hardSPL and unzip the only program I can use is the kaiser customRUU. The kaiser_hardSPL_1.0.nbh tells me I need to download a program to run. Can anyone tell me what program I need on my computer to run this application?

[my95z34]

Hi, I am not new to flashing roms, I've flashed many to my 6700 and my Mogul before. But for some reason I just can't do it on my Tilt.

I followed all the instructions on the first post, and successfully flashed the splash screen, but every time I try to flash the bootloader or a custom rom it doesnt move from 0% and the connection times out. What happened?


Thanks in advance.

[rusjul]

Hi,

I am having a problem installing the Hard SPL for my Tytn II device which i purchased last week. I Downloaded all the HARD SPL's from this Thread and and tried wothout and success. The screen always gets stuck after the tri-color screen and then into 0%. I have been doing ROM updates for my HTC Universal device.

Details of my device are as follows:

Bootloader:

KAIS130
SPL-1.93.0000
CPLD-8
--------------------
ROM Details:

ROM Versions : 1.56.405.5
ROM Date : 08/28/07
RADIO Version : 1.27.12.32
Protocol Version : 22.45.88.07H

-----------------------------

Unit Production Date : 181007(RC01) / EU

------------------------------------------------------

Please if anyone has a solution to this.

[fleety]

Hi there,

I just bought a new TyTNII yesterday, tried to HardSPL using Kaiser Hard-SPL v1 but stuck at white screen. So I tried the steps suggested by jockyw2001. Running JumpSPL1.56-KAIS.exe, I got USB on the display. Everything seems fine until this step. But then, when I unplug the USB cable (ActiveSync grey), and replug again, I cannot establish Activesync anymore. Tried 5 times, same result. I am running Vista Ultimate.

Any help people?

-Red-




Edit: Solution

1. After you run JumpSPL1.56-KAIS.exe, you will get the Rainbow screen on your device with "USB" appears on it
2. Unplug and replug. IMPORTANT: The activeSync will not establish. So what you need to do is to make sure the USB is connected. How? Open your PC/Laptop's Windows Device Manager. In Vista, you should find "Mobile Device" in the device list. In XP, if not mistaken, you should get something like "Windows Mobile". This shows that USB connection to your Kaiser is working (although ActiveSync not sync).
3. Run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC, then follow instructions. Your Kaiser will reboot after this completed.
4. Just to make sure things are all okay, hold power+camera+reset and check the BootLoader screen, if successful you should see "SPL-1.0.OliPof" in the second line. Soft reset.

So does this work? I thought KaiserCustomRUU.exe updated the ROM. Isnt the point of this thread that people cant install HardSPL.

Fleety

[xmoo]

You guys who have WHITE SCREN ISSUES!!

READE: http://forum.xda-developers.com/showthread.php?t=372134

[chrisnash]

For those who cannot install the HardSPL and don't wonna read this thread (http://forum.xda-developers.com/showthread.php?t=349476), here is the solution: