My i-teq X-bond is Dead

[s_m_s]

Hi All,
While Upgrading My i-teq x-bond ROM...
I Followed the Steps but after Checking the Image...
I Reset My Phone...
Now it doesn't response, I can only see the light when I'm charging the Phone!!!
Nothing else response...
I tried to Press (Call+End Call+Power) again to ReInstall the ROM But it also doesn't Response...


Also I want to know how to Enter Bootloader???
and How to enter the Engineering Mode???
Thanks
i am mohsen from iran tehran

[mahdi_hamvatan]

Hi All,
While Upgrading My i-teq x-bond ROM...
I Followed the Steps but after Checking the Image...
I Reset My Phone...
Now it doesn't response, I can only see the light when I'm charging the Phone!!!
Nothing else response...
I tried to Press (Call+End Call+Power) again to ReInstall the ROM But it also doesn't Response...


Also I want to know how to Enter Bootloader???
and How to enter the Engineering Mode???
Thanks
i am mohsen from iran tehran
you can press start + ok + reset. it will help you recover your pda

[mahdi_hamvatan]

salam agha mohsen man ham moshkele shoma ro daram agar dorostesh kardin man ro ham khabar konid. 09195388556
ghorboone dastet

[SKYWOR]

Hi All,
While Upgrading My i-teq x-bond ROM...
I Followed the Steps but after Checking the Image...
I Reset My Phone...
Now it doesn't response, I can only see the light when I'm charging the Phone!!!
Nothing else response...
I tried to Press (Call+End Call+Power) again to ReInstall the ROM But it also doesn't Response...


Also I want to know how to Enter Bootloader???
and How to enter the Engineering Mode???
Thanks

[lyndel4]

Hi All,
While Upgrading My i-teq x-bond ROM...
I Followed the Steps but after Checking the Image...
I Reset My Phone...
Now it doesn't response, I can only see the light when I'm charging the Phone!!!
Nothing else response...
I tried to Press (Call+End Call+Power) again to ReInstall the ROM But it also doesn't Response...


Also I want to know how to Enter Bootloader???
and How to enter the Engineering Mode???
Thanks
wait we need more Details id you try leaving the phone charging then take battry out and put it back in? also does the Device power on? I mean do you see the qtex screen you know the boot screen? also try putting it in bootloader mode then flash

[Wizzard]

I have been facing the same kind of problem. The phone light flashes when charging and when I boot the phone, it just shows the iteq logo. I have tried the Call Start+Call end+power combination but nothing happens. Sometime it shows the orange light besides the power button but the logo still remains on the screen. On one ocassion, it did enter some image mode but gave an error that no image found. I dont have the rom either to flash it. Can someone please post the rom online if they have it and also help if they have faced similar issues.

[faizan_versatile]

try
Windows flag button (Start)+OK+reset
if it doesn't work then install new windows

[jpppderttesss]

1 press and hold the [WIndosFlag(start)] and [ok] buttons somultaneously
2 press and release the [reset] button
3 wait up to the leds in the keyboar flahsing 2 or 3 time (less tha 5 seconds)
4 release the [WIndosFlag(start)] and [ok] buttons
must be start the resetting to the fabrique settings

[WIndosFlag(start)] button is in the down left corner
[ok] button is in the down right corner

if this not works the the keypad is dammage

[asingotot2]

When the battery is totally drained, all you have to do is charge it. Now here is the tip. when you charge it(totally drained iteq x-bond battery), the phone will enter into pre-charge mode for about 30min to 2 hrs( depending on how drained the battery is), the end-call button together with the right double arrow button will light steadily. Do not on the unit as this will only aggrevate the problem. Wait until the phone passes through that pre-charge mode. When the end-call button starts to flash, that means the pre-charge period is over. You can now press and hold the on/off button for about 5 seconds and the phone will start-up normally. Your problem is solved. That's it. This procedure will work only on the presumption that you did not do anything on the phone beforehand such as upgrading etc....