Problem Using Uspl

[gingerr6]

Step 1 hard reset.
step 2 connect and sync
step 3 run USPL from standalone, O2 Premium 2.0 Full or Artemis Touch 3.01 full
ALL fail.

get black screen with linux icon green wrighting then it goes black.

actuve sync icon goes white.

Only way to restart is take the battery off and reboot.

Any help :)

Using a 02 xda Orbit.
IPL 3.04.0001
SPL 3.04.0000
GSM 2.67.90
OS 3.4.0.0 i think.

thanks James.:D

[TangerineTractor]

Make sure your battery is over 50%!

Mine did this a couple of times... do a hard reset, then uspl.

[gingerr6]

Make sure your battery is over 50%!

Mine did this a couple of times... do a hard reset, then uspl.

Batt FULL
done 2 hard resets ?

done it 3 or 4 times ?

[fleggsy]

Exactly same problem here. Screen goes white, loses activesync connection and never comes back. I do then get the Windows 'Found New Hardwarde' screen, so am thinking this is more to do with the XP setup. Will try at home later!

Using a WM6 02 xda Orbit.
IPL 3.04.0001
SPL 3.04.0000
GSM 02.67.90
OS 3.4.0.0

[gingerr6]

Exactly same problem here. Screen goes white, loses activesync connection and never comes back. I do then get the Windows 'Found New Hardwarde' screen, so am thinking this is more to do with the XP setup. Will try at home later!

Using a WM6 02 xda Orbit.
IPL 3.04.0001
SPL 3.04.0000
GSM 02.67.90
OS 3.4.0.0

At least im ont alone :) or :(

[gadjet]

Step 1 hard reset.
step 2 connect and sync
step 3 run USPL from standalone, O2 Premium 2.0 Full or Artemis Touch 3.01 full
ALL fail.

get black screen with linux icon green wrighting then it goes black.

actuve sync icon goes white.

Only way to restart is take the battery off and reboot.

Any help :)

Using a 02 xda Orbit.
IPL 3.04.0001
SPL 3.04.0000
GSM 2.67.90
OS 3.4.0.0 i think.

thanks James.:D

Hi gingerr6 and fleggsy,
I had a similar problem with the USPL program.
My work around was to use one of the USPL'S included in the many rom's posted here on XDA-Developers, so I used the artemis vanilla 2.01 supplied USPL and it works fine.
I have removed only 1 files to cut down on the file size, i.e I removed the artemis_vanilla_2.01_WWE.nbh main file (53.960Mb).
Use this only to USPL your device, it wont flash the vanilla 2.01 rom as the file is removed.
Hope this helps you both.
Just run "STEP 1 - activesync then uspl cid unlocking.bat"


http://rapidshare.com/files/89152338/Artvan2_uspl.zip

NOTES:
1-Make sure you remove your memory and sim card before flashing.
2-Make sure your PDA is fully charged.
3-Make sure that active sync (or windows mobile device centre in Vista) see's your PDA first.

[mr.valacky]

remove the memory card and try again.

[gingerr6]

Hi gingerr6 and fleggsy,
I had a similar problem with the USPL program.
My work around was to use one of the USPL'S included in the many rom's posted here on XDA-Developers, so I used the artemis vanilla 2.01 supplied USPL and it works fine.
I have removed only 1 files to cut down on the file size, i.e I removed the artemis_vanilla_2.01_WWE.nbh main file (53.960Mb).
Use this only to USPL your device, it wont flash the vanilla 2.01 rom as the file is removed.
Hope this helps you both.
Just run "STEP 1 - activesync then uspl cid unlocking.bat"


http://rapidshare.com/files/89152338/Artvan2_uspl.zip

NOTES:
1-Make sure you remove your memory and sim card before flashing.
2-Make sure your PDA is fully charged.
3-Make sure that active sync (or windows mobile device centre in Vista) see's your PDA first.


Have not removed my sim so i will try that.
will dowload and try the attached file, thanks :)

[gingerr6]

i have the 02 xda orbit.
i take it the is the right forum and it is a HTC Artemis ?

just checkin LOL.?

[gadjet]

i have the 02 xda orbit.
i take it the is the right forum and it is a HTC Artemis ?

just checkin LOL.?

Yes the device is know by many names, take a look here for all the details you require.
http://wiki.xda-developers.com/index.php?pagename=HTC_Artemis

[gingerr6]

Yes the device is know by many names, take a look here for all the details you require.
http://wiki.xda-developers.com/index.php?pagename=HTC_Artemis

FANTASTIC :) thanks.

[gingerr6]

Have not removed my sim so i will try that.
will dowload and try the attached file, thanks :)

NOPE !!!!! followed ALL advise still not working ?

I must be doint something wrong ?

James.

[fleggsy]

Gadjet / mr.valacky - thanks for your time guys, but I'm afraid I still have to side with gingerr6. The problem is the same on all machines. The screen goes white and the active sync connection gets lost.

Have tried without sim and memory cards on my work PC running Win XP and my home PC running Win XP. Also tried on my Vista laptop but understand that there may be other issues there with Windows Mobile Device Center.

There is only 4mb of space on the phone currently, but would this matter if it's gonna get wiped anyway?

Haven't tried your artemis vanilla 2.01 yet Gadjet, plan to today when I get a few minutes.

Cheers!

[gingerr6]

have followed all information
even changed then usb cable.

this where i get to see attached.

is this right and if so how long should it take ?
also what happens after this does it load windows back up and then you flash from there or do you flash from this screen ?

Many thanks James.

[fleggsy]

In my limited (not fully working) experience James, it stays like your screenshot for approx 5 seconds, and then the whole screen goes white and this is where I lose activesync. It may go blue at this stage apparently (which is also ok) but as long as you have your activesync connection you can then proceed with the flash of the USPL and then the ROM of your choice.

[gingerr6]

In my limited (not fully working) experience James, it stays like your screenshot for approx 5 seconds, and then the whole screen goes white and this is where I lose activesync. It may go blue at this stage apparently (which is also ok) but as long as you have your activesync connection you can then proceed with the flash of the USPL and then the ROM of your choice.

YERRRRRRRRRRRR !!!!!

done it
mine went black, and lost active sysn icon but you carry on and flash with rom 9.99 or something will update to 100 VERY quickley.

then it restarts and you will see the SPL has changed to 1.1.000.000 or something, then once in windows active sysn and flash the rom .

mine is working GREAT , all be it only up fot 2 mins :)

[fleggsy]

Gadjet, tried the vanilla uspl too and this has exactly the same results for me. Oh well, just have to keep factory O2 WM6!

[gadjet]

Gadjet, tried the vanilla uspl too and this has exactly the same results for me. Oh well, just have to keep factory O2 WM6!

Hi gingerr6 and fleggsy.
I have had that happen to me loads, and my only way was to hard reset and try again.
Hold down the 2 top hardware keys and press soft reset button. (Contact & Calender buttons)
Last night it happened while flashing the a new rom.
Hope this helps..

[fleggsy]

YERRRRRRRRRRRR !!!!!

done it
mine went black, and lost active sysn icon but you carry on and flash with rom 9.99 or something will update to 100 VERY quickley.

then it restarts and you will see the SPL has changed to 1.1.000.000 or something, then once in windows active sysn and flash the rom .

mine is working GREAT , all be it only up fot 2 mins :)

Congratulations gingerr6. I tried just going on but without an activesync connection, it tells me it cannot connect to my phone.

http://anaquasupport.com/errror-260a.JPG

[gingerr6]

Congratulations gingerr6. I tried just going on but without an active sync connection, it tells me it cannot connect to my phone.

http://anaquasupport.com/errror-260a.JPG

take out memory and sim do hard reset sync and try and use start_uspl.exe
not STEP 1 - active sync then uspl cid unlocking.bat in Artemis vanilla 4.01

thats how i did it :)
don't worry if the sync logo goes white or disappears just carry on the 1 st step to change the SPL after it restarts you will see it on boot up but it will boot into your old ORIGINAL rom.

now run step 2 this will update the rom :)

[gingerr6]

is that your picture?

if so looks like your using an old program should be 3.6.3.5.

[fleggsy]

Wahhhheeyyy!:D

Cancel the cops, finally managed the upgrade this morning!
Still took a few goes, but finally got there.

1. Used Win XP home PC rather than Win XP at work. Removed memory and sim cards. Hard reset prior to each attempt. Screen went white, lost activesync connection with the icon going white and the program saying not connected. Followed gingerr6's advice and continued anyway. First attempt Error 260.
Started again from 1. Second attempt Error 220. Started again from 1.
2. Continued past where previously I was getting errors and it recognised the Orbit even though activesync wasn't very active. I hadn't done anything else different this time to make it work. Although I did make sure I was doing a hard reset for every attempt at the upgrade.

Very pleased now, thanks to everyone for the help. Now back to playing with the new phone! :)

[gingerr6]

Wahhhheeyyy!:D

Cancel the cops, finally managed the upgrade this morning!
Still took a few goes, but finally got there.

1. Used Win XP home PC rather than Win XP at work. Removed memory and sim cards. Hard reset prior to each attempt. Screen went white, lost activesync connection with the icon going white and the program saying not connected. Followed gingerr6's advice and continued anyway. First attempt Error 260.
Started again from 1. Second attempt Error 220. Started again from 1.
2. Continued past where previously I was getting errors and it recognised the Orbit even though activesync wasn't very active. I hadn't done anything else different this time to make it work. Although I did make sure I was doing a hard reset for every attempt at the upgrade.

Very pleased now, thanks to everyone for the help. Now back to playing with the new phone! :)

Great :)

something i did do was change my cable and it worked so maybe worth getting a new usb cable :)

[ProvRobbie]

Hey Gingerr, did you get this sorted?