MDA VARIO 3 stuck at RGB screen! PLEASE HELP

[Baronic]

Help!!! MY hardspl flashing is not moving at 18% i dare not unplug or do anything! its been 5 minutes and its supposed to take a minute onli? PLSSSS HELP!


UPDATE: says there was a communication error, i followed the recovery steps, and from there tried to continue. But then it said ready to continue update, but then cant connect! I'm stuck at tricolour with the word USB at the bottom. MDA Vario3 here. PLEASE HELP ME!!

[Baronic]

BUMP please help me guys.....please...

[Baronic]

bump out of desperation. please guys....i'm sure u guys know what to do, so please help me

[AllTheWay]

bump out of desperation. please guys....i'm sure u guys know what to do, so please help me

flash to your original shipped ROM via MicroSD card.

[Baronic]

I've searched everywhere via google and even XDA forum, but i can't find an original T mobile Rom.

[dikkedonder]

try flash it with diffirent bootloader ( spl ) en try it again.

[NetrunnerAT]

All wrong!

If you stuck in the 3 Color Mode ... then ... you havent Read the First Post carefully!

To fix it ... Download the Programm MTTY -> Deactivate Active Sync -> Connect with MTTY over USB -> Enter "Boot" without ""

Then you must stay in your OS!

Then Read the First Post of the HardSPL Threat.

Copy SSPL to your Phone and not to the SD-Card or something like else. Start it -> You are in the 3 Color Mode with 1.16.Jump -> Flash HardSPL again!

If MTTY Boot not work, you can Try the OEMSBL and use the Command "cego"

If you have device fucked up ...

You must know, what CID your Device have ... Iif you have buy your Phone in UK ... possible your CID is UK or WWE. Download a Full Rom with CID WWE or UK and Flash it! It restore your SPL, OS, Radio, ....

If any think stand about wrong ID ... you have use the wrong ROM with the wrong CID ... search for a other Rom and try it!

I mean not Cooked or Edit Roms!!!!!!! I mean Full HTC Roms!!!!!!!

If you doesnt find anything ... try www.htc.com -> eclub and hope your IMEI is permited to use it :->

[Baronic]

Thanks NetRunner AT for a detailed reply! :D I did read up and found out about MTTY, but i didnt have any rom to flash since i havent CID unlocked it. I'm now trying from this link

http://forum.xda-developers.com/showpost.php?p=1586817&postcount=2

hopefully something there works. Will update this thread also for future people who face the same problem.

UPDATE: After using "boot" with MTTY i get a pda with a screen that changes from 3 colour > White > Gray > 3 Colour and continue.....so....what do i do now? I also cant flash the original rom, stuck at 0% with communications error

[GSLEON3]

Dude, The people above, while trying to help, & that's nice, are giving you incomplete information.

Please PM me & I'll help you figure it out. The first thing I'd like you to do is run a diagnostic. (Like any good recovery specialist would have you di, FIRST)

Use MTTY, make sure to change the "Flow Control" to RTS/CTS, & when you get to the cmd> prompt enter like this: cmd>info 8

Post the return or even better, PM it to me so we can see what went wrong. You can tell by the location of the bad blocks where the issue is.

I also need to know what your SPl version is, because different spl's can have different valid commands.

[Baronic]

DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40

Checking block information

BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 529 (0x211) is bad block
BLOCK 965 (0x3C5) is bad block
BLOCK 967 (0x3C7) is bad block
BLOCK 969 (0x3C9) is bad block
BLOCK 971 (0x3CB) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x8800
Partition[3], type=0x4, start=0x9540, total=0x11D80

CE Total Length(with sector info) = 0x4AEAA00
CE CheckSum Length(without sector info) = 0x4AA0000


as for the spl i'm not sure if its right since i was halfway Hard-SpLing when i had a communications error.

but this is what i see

KAIS130
SPL-1.56.0000
CPLD-8

[GSLEON3]

Solved

Glad I could help you out!

Another notch on my belt. Close this thread.