Hp h2200

[Profy_X]

If anyone can help i have a hp ipaq h2200 and i tryed to do a bios update but now it`s stuck the onley thing that shows me is a image with hp,usb and v1.08 can anyone help me please?is there any way i can make it work again?is there any ROM for this kind of device maybe a wm5 or wm6?:confused:

[Profy_X]

no one can help me?:confused:

[basf]

If anyone can help i have a hp ipaq h2200 and i tryed to do a bios update but now it`s stuck the onley thing that shows me is a image with hp,usb and v1.08 can anyone help me please?is there any way i can make it work again?is there any ROM for this kind of device maybe a wm5 or wm6?:confused:

go boot loader mode before upgrade

[Profy_X]

but how do i do this?it isn`t in bootloader?(it shows a hp image up shows usb and down v1,08):confused:

[Profy_X]

:confused:...

[bigu1975]

First important question: what upgrade did you try to do?
For iPAQ h2200 there is no cooked ROMs: WM5 or WM6x. This device can work only under branded WM2003se.

If you tried to do upgrade to any of cooked ROM like WM6.0 from different device like hx22xx by mistake, please try the following:
1. Go to HP www page and download the last available ROM upgrade (I assume English ROM)
2. Turn on iPAQ (don't carry the device doesn't boot properly) and place it to the cradle which should be connected to PC which has installed active sync software (please don't carry about lack of connection seen on active sync).
3. Run the ROM upgrade.

If you tried the HP upgrade and it stuck - just repeat them with the way described above.

Important - do not use blue tooth connection during flash !!! Only USB !!!

Good luck.
If it doesn't help I believe there is hundred of similar cases described in forums - try to search the solution there :)

[Menneisyys]

This device can work only under branded WM2003se.

More precisely: WM2003 only - no SE upgrades for the h2210.

[Profy_X]

i upgraded the v1.10 original ROM from HP home site but now i solved the problem with mtty and ultra edith but now i have a nother problem i flashed again the ROM but its stuck on the loggin bar from startup :( it just fill the bar but windows doesn`t start i tryed again to flash and the problem still persist any sollutions?:confused:

[bigu1975]

i flashed again the ROM but its stuck on the loggin bar from startup :( it just fill the bar but windows doesn`t start i tryed again to flash and the problem still persist any sollutions?:confused:

As I understand you correctly - you restored your iPAQ into live using the last available ROM from HP site, which is WM2003 (thank you Menneisyys). The iPAQ worked fine and then you was trying to make another ROM upgrade - which ROM did you use?

I am asking because the ROM in version 1.10 is the most actual one and there is no any other ROM for this device. I assume that source of your problem is you are trying to use incorrect ROM. Correct me if I am wrong... If this is true - the solution is to restore your device into operational using the way as you did it before and stop to flashing your device - there is no another ROM to your iPAQ :)

[Profy_X]

the v1.10 but the problem is that after i flash the wm doesn`t start it just stay there stuck on the startup and i reflashed the device but still doesn`t start :(

[ThaMasterT]

how did u fix the stucked screen while booting? im searching for solutions for 30 mins now, but dind't find a way...

please help somebody..

[ThaMasterT]

ok, for those with "same" problems like me:

i have windows 7 64bit. the rom flashing wasn't successfull on this machine. i did the same on my notebook with windows xp and it worked. before it said that it couldn't find my ppc. on the notebook it wasn't a problem.

i had these installation notes found anywhere:
1.) Go to the Vendor Website, and...
2.) Select the appropriate hyperlink for your model.
3.) Download the most recent BIOS version.
4.) Press the POWER + iTASK + CONTACTS + RESET buttons at the same time so as to enter the FLASH Mode
5.) Make sure your USB connection to the Cradle is hooked-up.
6.) Place your PDA in the USB Cradle.
7.) Stop the MS ActiveSync session on your HOST PC: CTRL-ALT-DELETE > TASK MANAGER > PROCESSES.
8.) Highlight WESCOMM.EXE and select "End Process" button.
9.) Run the file you downloaded from your Vendor in step 3.
10.) The PDA should now begin Flashing the iPAQ's ROM BIOS.

i ignored step 4.)

hope that it helped somebody :)