harperbrad
13-06-2008, 09:26 PM
I've long been using cooked ROMs on my Wizard. I recently updated to an ATT Tilt and decided not to waste my time with the ATT rom and went straight for Dutty's latest. Here's what I did:
1) Set up Activesync as per normal, synced data to ATT stock phone
2) Ran Pof's kaiser-HardSPLv1 script
a) It completed without error
b) Didn't notice any obvious changes
3) Downloaded NEON_Radio_Only_1[1].58.25.17_CustomRUU from Dutty's thread.
a) Seemed strange it was called Radio_Only...
b) Ran KaiserCustomRUU
c) Everything loaded correctly
4) Device rebooted itself, ended up with "static" of random pixels on screen.
a) Had "Oh shit" moment
5) Tried a soft reset, with the following results:
a) ATT Logo, reports following info:
R: 1.58.25.17
G: 25.69.30.05H
D: 1.62.00.00
b) ATT 3G Animation
c) Blank screen (sometimes will show static, especially when plugging/unplugging USB cable)
6) Tried a hard reset, with the following results:
a) Warning about going to manufacturer's settings, hit "Send"
b) Restore scroll completes
c) Clicked "Send" to boot
d) Goes through ATT logo w/ same info
e) Green WM logo screen, no info
e) Tap screen to setup up windows mobile device
f) Went through WM setup screens (time, calibration, password, etc)
f1) Sometimes just beeps rather than doing setup screens
g) Starts installing customization files
h) Reboots, go to step 5.
7) Tried mtty
a) Reports "USB port cannot open"
b) Kicks out to a mostly empty tool
Other things I've tried:
1) Moving the USB port (between ports of hub, straight in the laptop)
2) Plugging/unplugging USB port
3) Using KaiserCustomRUU to reflash rom (get Error 260, cannot connect)
I'm stumped. I've got 10 windows up with different threads and can't seem to find anything that helps. Anyone have some advice?
--HarperBrad
1) Set up Activesync as per normal, synced data to ATT stock phone
2) Ran Pof's kaiser-HardSPLv1 script
a) It completed without error
b) Didn't notice any obvious changes
3) Downloaded NEON_Radio_Only_1[1].58.25.17_CustomRUU from Dutty's thread.
a) Seemed strange it was called Radio_Only...
b) Ran KaiserCustomRUU
c) Everything loaded correctly
4) Device rebooted itself, ended up with "static" of random pixels on screen.
a) Had "Oh shit" moment
5) Tried a soft reset, with the following results:
a) ATT Logo, reports following info:
R: 1.58.25.17
G: 25.69.30.05H
D: 1.62.00.00
b) ATT 3G Animation
c) Blank screen (sometimes will show static, especially when plugging/unplugging USB cable)
6) Tried a hard reset, with the following results:
a) Warning about going to manufacturer's settings, hit "Send"
b) Restore scroll completes
c) Clicked "Send" to boot
d) Goes through ATT logo w/ same info
e) Green WM logo screen, no info
e) Tap screen to setup up windows mobile device
f) Went through WM setup screens (time, calibration, password, etc)
f1) Sometimes just beeps rather than doing setup screens
g) Starts installing customization files
h) Reboots, go to step 5.
7) Tried mtty
a) Reports "USB port cannot open"
b) Kicks out to a mostly empty tool
Other things I've tried:
1) Moving the USB port (between ports of hub, straight in the laptop)
2) Plugging/unplugging USB port
3) Using KaiserCustomRUU to reflash rom (get Error 260, cannot connect)
I'm stumped. I've got 10 windows up with different threads and can't seem to find anything that helps. Anyone have some advice?
--HarperBrad