8125 stuck on 3 color boot screen

[lstubble44]

It says only ipl 2.25.0001 and spl 2.25.0001
I try a hard reset, but when it asks me to confirm by pressing SEND, I press SEND and nothing happens.. press any key and nothing happens, just sits there saying press SEND to confirm...
I tried flashing Cingular/AT&T's rom on to it, it was successful on the screen, but after rebooting, just went back into the 3 color screen...
Does anyone have any suggestions?

[lstubble44]

I just wanted to add, I have searched threads here on xda-dev and other sites, and have found similar issues - normally the other issues have been resolved in one way or another involving a hard reset, which my phone will not complete. When it asks me to press send, the phone freezes at that point and does not accept any key entries (except reset). I would really appreciate any input. I also have a theory-that I may attempt this evening-If you hold the camera button down and reset, it brings up the boot loader screen (if my information is correct)... could my problem be caused by a faulty camera button? Maybe internally the button is remaining closed, which could prevent it from doing anything on a reset outside of the boot screen? Any engineers around that may know this? I am going to attempt (hopefully with low heat) to remove the button this evening... possibly even repair or replace it if the phone works with the button removed...(these thoughts are based on my phone being dropped in the sand at the beach...maybe a grain of sand worked it's way into the camera's button housing and is holding the contact closed)

[lstubble44]

well thanks for no advice... i desoldered and removed the camera button (button 3). powered it on and the phone works. I reprogrammed the camera to button 5. (i also loaded a new WM6 rom and some other stuff) The last time I opened up the phone, I broke the itsy bitsy super micro tiny lock on the keyboard ribbon cable socket... so now my slide out keyboard doesn't work. I installed a full screen keyboard and set it to the messaging button (button 1) - the messaging button still brings up messaging with just a touch, but a long hold brings up a full screen touch keyboard that works fantastically!!! I am going to dismantle the very tiny micro switch and repair it, then resolder it back on the mainboard to make my camera work like it should again...and find a way to get the keyboard ribbon cable to lock into the socket...then my phone will be as good as new!

umm... thanks???

[scousemartin]

well congratulations on getting it working again. :)

[lstubble44]

I have taken the tiny little switch apart without breaking anything... one tiny grain of sand stuck under the button pressing on the switch plate... now i have to find a way to put the little switch back together... then attempt to solder it back onto the board without over heating nearby components. I have been playing around with Byka's cube... took a bit of tweaking to get it to work well.... not sure if I want to keep it or not... I have been trying to find htc cube, but no luck outside of a rom... which I may consider...but I just spent the past week reinstalling all of the software I use... Would like to just design my own windows for my phone if I had the time... Been working on an ion motor for an electric car...

I would like to thank everyone here at xda-dev. for all the information. Could not have learned so much, so quickly, if it weren't for this site.

oh... and I am using an 8125 (G4) with Faria Crossbow

[ymmp]

Hi!
I have the same problem (but I don't have much tech know how).
It all started when phone got wet (inc. in battery compartment).
My phone would not soft reset beyond the Bootloader, unless I leave the battery out for a few hours. Then once it loads up, after a short amount of usage 2 things happen: 1) every time I would turn it on (or get a call) it starts in Camera (you didn't report it but you must have had the same experience). 2) the buttons don't work properly.
It finally dawned on me the camera button might be stuck, I set the button to "none", and no more more automatic camera. I still need to free the button altogether as still causing button freezeup and also allow soft resets.
I don't know much about soldering.
Any ideas?
Thanks