TYTNII Flashing problem

[stoutseun]

Hi guys,

Yesterday I upgraded from my Vox (running Gonzo WM6.1) to a Kaiser and started reading up on how to flash a custom ROM. Much more info and ROMS than for the Vox!!!


Firstly, before I even checked here, I upgraded to the latest WM6.1 HTC Rom.

Since that, no luck. I've read several pages, wikis and what have you, but I can't get the phone flashed with any HardSPL. Tried several versions of JumpSPL and there after only connection errors when doing HardSPL. On using JumpSPL1.93 the words USB doesn't come up on the bootloader screen - only on 1.56 and the 3.28 on the phone itself.

On that - most posts says on the bootloader it would show "...Jocky..." or "...pof..." SPL version, but mine everytime just says the standard "CPLD-8". The leads me to think that somehow it doesn't want to run the custom SPL version. I tried the SDA unlocker tool too, but it says "The device can not be unlocked"

After trying 2 hours I'm ready to throw in the rope.... :(

[jahrami]

the word usb will not appear on screen!
you need to unplug and replug your usb cable, to shift from serial to usb
or use force usb versions of hardspl

Hi guys,

Yesterday I upgraded from my Vox (running Gonzo WM6.1) to a Kaiser and started reading up on how to flash a custom ROM. Much more info and ROMS than for the Vox!!!


Firstly, before I even checked here, I upgraded to the latest WM6.1 HTC Rom.

Since that, no luck. I've read several pages, wikis and what have you, but I can't get the phone flashed with any HardSPL. Tried several versions of JumpSPL and there after only connection errors when doing HardSPL. On using JumpSPL1.93 the words USB doesn't come up on the bootloader screen - only on 1.56 and the 3.28 on the phone itself.

On that - most posts says on the bootloader it would show "...Jocky..." or "...pof..." SPL version, but mine everytime just says the standard "CPLD-8". The leads me to think that somehow it doesn't want to run the custom SPL version. I tried the SDA unlocker tool too, but it says "The device can not be unlocked"

After trying 2 hours I'm ready to throw in the rope.... :(

[NotATreoFan]

the word usb will not appear on screen!

Yes it will, or it will not work. My Tilt has the exact issue. If I use JumpSPL 1.93, I will not get USB onscreen, and it will not communicate. If I use JumpSPL 1.56, I do get USB, and am able to communicate and flash.

...the words USB doesn't come up on the bootloader screen - only on 1.56 and the 3.28 on the phone itself...

If you load JumpSPL 1.56, and see USB onscreen, then follow the flashing instructions from that point (I don't bother with unchecking Allow USB Connections in ActiveSync), and HardSPL will flash successfully. If you get a communication error, switch USB ports; preferably to a different USB controller (i.e from front USB to back USB).

[stoutseun]

Thanks guys - I tried that all. Get to the stage where it shows the percentage bar and stays on 0% until the errors stops it all. :mad:

[NotATreoFan]

Thanks guys - I tried that all. Get to the stage where it shows the percentage bar and stays on 0% until the errors stops it all. :mad:

What error message? Each error number means something different.

[stoutseun]

Connection error. Tried various methods now and on two different pcs, but no luck. I think it's something to do with the phone being locked.

Is the SDA_Unlocker utility generic or is there a specific version for the Kaiser? I get an error saying "Phone is not unlockable"