Pls help, stuck in bl SPL-2.07 Telus

[belmont]

i was with DCD 3.2.5 and wanted to flash to new telus wm6.1 from telus... now i'm stuck with bl spl-2.07...tried to flash back with stock rom Telus_HTC_P4000_WM6_07252007 but at 1% it says not compatible...tried also uni_exitbootloader but nothing happen...whenever tried to flash with SD card...it's always keep saying "loading...", is anyone have suggestion to bring back my mogul to life?

thanks

[scrawnyb]

uhh 2.07 is a relocker SPL

I think you have to downgrade to a stock firmware/SPL, then do the process properly.

Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.

[scrosler]

uhh 2.07 is a relocker SPL

I think you have to downgrade to a stock firmware/SPL, then do the process properly.

Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.



I would say the same. I would go ahead and unlock OliPro 2.4 (never tried 2.47) then flash Telus rom. After doing so you should be fine.

[belmont]

uhh 2.07 is a relocker SPL

I think you have to downgrade to a stock firmware/SPL, then do the process properly.

Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.

what do you mean by "I think you have to downgrade to a stock firmware/SPL" ? du you have any recommendation ?

[scrosler]

what do you mean by "I think you have to downgrade to a stock firmware/SPL" ? du you have any recommendation ?

Sorry, I read his post wrong. HEre is what I would do:

1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.

2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.

3. Flash your Stock ROM back.

4. Hard Reset.

In my experience you do not have to go back to a stock ROM to flash a new carrier ROM as long as you have OliPro.

Let me ask you this: What exact steps did you take when you flashed Telus ROM image?

I was on the same setup you were, DCD 3.2.5 with Radio .50 and OliPro 2.40. I simply flashed the Telus image and all was well for me. Hell it was better than all well. This is the best ROM I have ever used. PERIOD. No, its not pretty but damn, its fast as anything I have used and the GPS is insane!

BTW: Im a Verizon user. Anyone know how to make the phone not say "Telus" when I go to the connection manager?

[belmont]

Sorry, I read his post wrong. HEre is what I would do:

1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.

2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.

3. Flash your Stock ROM back.

4. Hard Reset.

In my experience you do not have to go back to a stock ROM to flash a new carrier ROM as long as you have OliPro.

Let me ask you this: What exact steps did you take when you flashed Telus ROM image?

I was on the same setup you were, DCD 3.2.5 with Radio .50 and OliPro 2.40. I simply flashed the Telus image and all was well for me. Hell it was better than all well. This is the best ROM I have ever used. PERIOD. No, its not pretty but damn, its fast as anything I have used and the GPS is insane!

BTW: Im a Verizon user. Anyone know how to make the phone not say "Telus" when I go to the connection manager?

thanks for quick reply. i tried so many times to use olipro 2.40...whenever i ran it...it popup that device is not connected and asked me to try again...tried also with SD but still hung on tri-color bars

[scrosler]

thanks for quick reply. i tried so many times to use olipro 2.40...whenever i ran it...it popup that device is not connected and asked me to try again...tried also with SD but still hung on tri-color bars

Thats interesting. I have hosed so many XV6800's and used OliPro and a stock GPS sprint ROM to get them back (Thanks alot for nothing Verizon!).

IM assuming you are still on the tricolor screen? Take out battery and place back in. Then try again. Dont wait long. Someonelse has discoverd the phone can only be connected for so long before it "drops" connection with the windows machine. Someone else's therory but I can certainly second it.

What SPL were you using with DCD 3.x before upgrading?

[belmont]

Thats interesting. I have hosed so many XV6800's and used OliPro and a stock GPS sprint ROM to get them back (Thanks alot for nothing Verizon!).

IM assuming you are still on the tricolor screen? Take out battery and place back in. Then try again. Dont wait long. Someonelse has discoverd the phone can only be connected for so long before it "drops" connection with the windows machine. Someone else's therory but I can certainly second it.

What SPL were you using with DCD 3.x before upgrading?

before flashing to new telus wm6.1 rom, i had olipro 2.40 with .30 radio and dcd3.2.5 kitchen...i have tried upgrading to radio .50 with no success. but failing to update radio didn't affect anything to my phone. tried your suggestion by romoving battery and still telling me that device not connected.

[scrosler]

before flashing to new telus wm6.1 rom, i had olipro 2.40 with .30 radio and dcd3.2.5 kitchen...i have tried upgrading to radio .50 with no success. but failing to update radio didn't affect anything to my phone. tried your suggestion by romoving battery and still telling me that device not connected.

Hmmm, maybe try a different USB port at this time. Also, try this...

Before you connect your device open device manager in Windows. Look for M/S USB sync to appear after you connect. What OS are you using? This is what it will look like in Vista.

In XP I beleive it will show up under USB at the very bottom of Device Manager.


Does the phone show up at all?

[flyers2114]

Flash a stock pre-gps rom first.....then go ahead and upgrade the hard spl to 2.4 or 2.47.....then flash away with whatever you want....

You cannot flash Hardspl to Hardspl...they have overwrite protection not signed by HTC....

[memezgebia]

..................................