SPL 2.40

[JukEboXAuDiO]

Ok so I just got my new device and I tried to update the bootloader from 1.04 to 2.47 with the new SPL with the .exe file form here. It restarted to flash and it froze. What do I do? I can't boot it to the OS and I can't update the bootloader. Please Hlep ASAP. I am stuck with SPL-104 and windows 6

Thanks.

[lafester]

if you can't get out of bootloader you may have to flash a stock non gps rom.

[JukEboXAuDiO]

I am jsut flashing the bootloader. It had the original stock ROM on it.

[flyers2114]

if you can't get out of bootloader you may have to flash a stock non gps rom.

lafe is right.....flash a stock non-gps rom.......when you tried flashing the Nuespl 2.47 you did do it via SD card correct?

[JukEboXAuDiO]

yes I did. I flashed it on a Non GPS stock VZW ROM

[flyers2114]

yes I did. I flashed it on a Non GPS stock VZW ROM


try flashing another stock non gps rom and then try to upgrade the BL again....this time try Olipro 2.4.....somehow the BL didnt flash correctly the only way out is to flash the stock non-gps rom and the proceed...

[JukEboXAuDiO]

I am using OliPro 2.4 from the DCD ROM thread. Is that the wrong one? Its stuck ont he loading screen

[flyers2114]

I am using OliPro 2.4 from the DCD ROM thread. Is that the wrong one? Its stuck ont he loading screen


No....but above you posted 2.47.....you could try Nuespl 2.47 it is the latest and greatest...go over to PPCgeeks and grab it off my sig over there....it runs fom the SDcard....also what have you tried to get it back?.....if you have not already try a hard reset first.....

Here I will save you some time

http://forum.ppcgeeks.com/showthread.php?t=30561&highlight=hardspl+2.47

[JukEboXAuDiO]

yes I have tried hard reset. It keeps going to hte bootloader. Ok i used Olipro 2.40 using hte cmd prompt and did what it told me to. When it restarted it got stuck on the updating page. Now its just stuck onthe loading page.

[flyers2114]

yes I have tried hard reset. It keeps going to hte bootloader. Ok i used Olipro 2.40 using hte cmd prompt and did what it told me to. When it restarted it got stuck on the updating page. Now its just stuck onthe loading page.


Can you enter BL?

[JukEboXAuDiO]

Yes. It loads to bootloader 1.04 and then goes to update from the SD Card and its stuck on the loading screen

[flyers2114]

Yes. It loads to bootloader 1.04 and then goes to update from the SD Card and its stuck on the loading screen

ok let me make sure I understand.....you are in BL? which are trying to Un-lock with Olipro 2.4 or nuespl 2.47?

[JukEboXAuDiO]

I am truing to unlock Olipro 2.4

[lafester]

I am a little confused also. Its been awhile since I flashed olipro 2.4... Aren't you supposed to pull usb at some point during the install?

you have to follow ALL of the instructions for the flash to work.

Nuespl 2.47 is much easier to use. I would still recommend reflashing the stock rom so you can put nuespl on your sd (providing it is 2gb or less).

if you are in bootloader you can just run the ruu and it will flash.

[flyers2114]

I am truing to unlock Olipro 2.4

and you are trying to un-lock with Olipro 2.4 via sd.....if that is so then that is the problem....

[JukEboXAuDiO]

and you are trying to un-lock with Olipro 2.4 via sd.....if that is so then that is the problem....

Its stuck on the loading screen.

[JukEboXAuDiO]

Can someone tell me where I can get the dman nbh file so I can re flash it back to what it should be so I can start over? All I have is a damn phone with no OS and bootloader 1.04.

[nitro66215]

Can someone tell me where I can get the dman nbh file so I can re flash it back to what it should be so I can start over? All I have is a damn phone with no OS and bootloader 1.04.
1.04 is verizon's stock bootloader. Do these steps with an SD card. You can try using Verizon's stock OS/Radio... but it never works for me the first time.

1) Download the Sprint latest Rom Update. Right click the EXE file and extract the files.
2) Copy and rename Ruu_signed.nbh to TITAIMG.nbh on the storage card.
3) Put the card into the phone...Power+Camera+Reset. This will get into bootloader, and load the image.

When complete.... soft-reset.

DO NOT LET CUSTOMIZATIONS RUN!!!

When you get to the WM 6.1 screen and it asks for you to touch screen... DO NOTHING!!!

Remove SD card.

Connect your USB cable... get activesync to see it... Just tell it to cancel the syncronization.... Then run Olipro's Titan Unlocker 2.4.


When it's done getting 2.4 on it.... Copy the radio rom you want IE 3.42.50 to the SD card and flash away. Then the same for the new OS.

[JukEboXAuDiO]

Thank you so much dude. I am gonna get this thing moving today. Thanks again!

[nitro66215]

Thank you so much dude. I am gonna get this thing moving today. Thanks again!
No problem. It does get tricky, but once you get the hang of the concepts.... flashing back and forth is easy. :D

[JukEboXAuDiO]

Ok another question. I can't get my data connection to work. I got the radio working, along with DCD 3.2.6 and I programmed the phone and installed the carrier cab. Am I missing anything?

[nitro66215]

Ok another question. I can't get my data connection to work. I got the radio working, along with DCD 3.2.6 and I programmed the phone and installed the carrier cab. Am I missing anything?
What message are you getting when trying to connect to the internet?

[kdj67f]

Nevermind... :o