Kaiser 100 (TILT 8925) died during Flashing.

[er1cc]

Kaiser 100 (TILT 8925) during Flashing, the battery was discharged. Now it does not join, the green light diode only burns at power ON attempt.
The computer defines it on USB as Flash device, but the driver from ActiveSynch do not approach.
How to restore it ?
What buttons for input in Flash mode (tricolor) ?
BR !

[kareeem]

This is in the wrong section of the Kaiser.

Anyhow, enter bootloader mode by fully pressing the camera button and doing a soft reset simeltaneously. Once you're there, flash a ROM.

[er1cc]

This is in the wrong section of the Kaiser.
Sorry.
Mod's remove my topic to right place, please.
Anyhow, enter bootloader mode by fully pressing the camera button and doing a soft reset simeltaneously. Once you're there, flash a ROM.
This combination don't work for me.
Any other idea's, please.
BR !

[kareeem]

It should work; you're just probably not doing it correctly. Make sure to have the camera button completely pressed and stylus in the reset whole for a few seconds until you get the tri-colored screen.

[er1cc]

It should work; you're just probably not doing it correctly. Make sure to have the camera button completely pressed and stylus in the reset whole for a few seconds until you get the tri-colored screen.
I did exactly as You wrote up.
I push camera button completely pressed and stylus in the reset whole for a few seconds
But, PC recognize it as Flash Device, and noone from ActiveSynch driver's does not approach for this mode.
Tricolor screen also not appear.

[cmonex]

eh, probably you have no SPL now...

install the Qualcomm drivers: http://forum.xda-developers.com/attachment.php?attachmentid=71038&d=1203255530

does that go OK?

[er1cc]

cmonex
Thank You !
Will try.
WBR !

[er1cc]

eh, probably you have no SPL now...

install the Qualcomm drivers: http://forum.xda-developers.com/attachment.php?attachmentid=71038&d=1203255530

does that go OK?
Yes, I installed Qualcomm drivers, and driver's is OK, thank You for driver's.
But what I must do now ?
How and what SPL I need write there ?

WBR !

[DaveShaw]

I think you need to use the FrankenKaiser SPL Loader...
But I am not 100%.

Ta
Dave

[er1cc]

I think you need to use the FrankenKaiser SPL Loader...
But I am not 100%.

Ta
Dave

From where I can get it ?
WBR !

[kristoff_sz]

From where I can get it ?
WBR !

Ok, your humble servant quit the job.

Now you must use the search button.

[DaveShaw]

From where I can get it ?
WBR !

Here: http://forum.xda-developers.com/showthread.php?t=394584

It says you need a security unlocked device. Do you know if you have done this?

If not, I'd wait for cmonex to have a look. I'm a novice at this ;)

Dave

[er1cc]

Here: http://forum.xda-developers.com/showthread.php?t=394584

It says you need a security unlocked device. Do you know if you have done this?

If not, I'd wait for cmonex to have a look. I'm a novice at this ;)

Dave

Yes !
Thank You, DaveShaw !
It is what I need.
But when I run FrankenKaiser-SPL-Loader.exe , WindowsXP closed DOS window with error.
What is wrong ?
I think better I need wait for mr. cmonex, for his answer about that.

WBR !

[DaveShaw]

Yes !
Thank You, DaveShaw !
It is what I need.
But when I run FrankenKaiser-SPL-Loader.exe , WindowsXP closed DOS window with error.
What is wrong ?
I think better I need wait for mr. cmonex, for his answer about that.

WBR !

I think that's best, but mr cmonex doesn't exists, mrs comnex on the other hand... :)

[er1cc]

......doesn't exists, mrs comnex on the other hand... :)
:) I wait.

WBR !

[cmonex]

Yes !
Thank You, DaveShaw !
It is what I need.
But when I run FrankenKaiser-SPL-Loader.exe , WindowsXP closed DOS window with error.
What is wrong ?
I think better I need wait for mr. cmonex, for his answer about that.

WBR !



what was the error?

and are you security unlocked at all?

also we better know your exact radio version because the described step 6 in that thread can differ (the exact command might need a different number to be typed). do you know the radio version?

if you answer with no to either of the last two questions, contact me in PM and we can look at it in more detail.

[cmonex]

I think that's best, but mr cmonex doesn't exists, mrs comnex on the other hand... :)

not mrs yet, no :D

[biscuits1978]

I thought you get to the tri-colored screen by holding down both the camera button AND the power button, and then do a soft reset?

[cmonex]

I thought you get to the tri-colored screen by holding down both the camera button AND the power button, and then do a soft reset?

no, power is not needed.

the way to do it:

hold camera, press reset (don't hold reset, just press it once), release reset, keep camera held for like 5 seconds then release it.

[DaveShaw]

not mrs yet, no :D

well definitely not mr. :D

Dave

[er1cc]

what was the error?

and are you security unlocked at all?

also we better know your exact radio version because the described step 6 in that thread can differ (the exact command might need a different number to be typed). do you know the radio version?

if you answer with no to either of the last two questions, contact me in PM and we can look at it in more detail.
Sorry for answer delay.
From begin:
- Have an Kaiser with unknown Radio version, without tricolor (boot mode).
PC sees it as Qualcomm modem, with battery or without battery no difference (strange).

Step's what I did:
1 power down
2 hold green send key and power on, the phone will enter radio bootloader (oemsbl)
- can't see, enter or not
3 connect with mtty1.42 (COM7) and type "dload" to put phone in dload mode
- MTTY sees mine KAISER but when I make type "dload", MTTY - hangs.

What is wrong ?

WBR !

[cmonex]

Sorry for answer delay.
From begin:
- Have an Kaiser with unknown Radio version, without tricolor (boot mode).
PC sees it as Qualcomm modem, with battery or without battery no difference (strange).

Step's what I did:
1 power down
2 hold green send key and power on, the phone will enter radio bootloader (oemsbl)
- can't see, enter or not
3 connect with mtty1.42 (COM7) and type "dload" to put phone in dload mode
- MTTY sees mine KAISER but when I make type "dload", MTTY - hangs.

What is wrong ?

WBR !


after step 2, please try typing "?" (without the quotes) and do not do step 3.

what does it reply with ?

[er1cc]

after step 2, please try typing "?" (without the quotes) and do not do step 3.

what does it reply with ?
Same: MTTY - hangs :(

[er1cc]

Same: MTTY - hangs :(

May I need use Win98 ?
But there is not driver's :(

WBR !

[DaveShaw]

May I need use Win98 ?
But there is not driver's :(

WBR !

I doubt that would work?

Windows XP is best for this.

Ta
Dave

[er1cc]

after step 2, please try typing "?" (without the quotes) and do not do step 3.

what does it reply with ?

When I connect KAISER to USB and send command "?" (without "" for sure), MTTY hangs 4rever.
When I disconnect KAISER from USB MTTY back to normal state, and write <CE-31><CE-1167>
I will soon go mad with it HTC.

[er1cc]

Noone have idea ?
BR !

[_MsG_]

What if you turn the phone off and then press power and camera simultaneously together. Did work here.

[er1cc]

What if you turn the phone off and then press power and camera simultaneously together. Did work here.
Nothing happen.
Can't enter BootMode (tricolor).
Just green LED on.
BR !