Please Help! TYTN II from WM6.0 To WM6.1

[Puff1911]

I have read through endless posts and stickies.. I still can't figure out what the correct procedure is for updating my TYTN II from WM6.0 to WM6.1

I would greatly appreciate it, if someone would lay it out step my step

I tried to flash with the WM6.1 update, it said there was a vender error.

I tried flashing with HardSPL 3.28 and it stops at 0% and says there is there is a communication error, and to click next to perform the recovery. I perform the recovery, after removing the battery and putting it back in, the phone starts up normal.

I tried the white screen solution.. it reaches the three coloured display with USB and just sits there.. i eventually reboot the phone.. and it starts back up normally..

but none of the flashing procedures have worked yet..

I used the files found Here (http://forum.xda-developers.com/showthread.php?t=354061) for the white screen problem.

I don't know what else to try..

Direct update - Invalid Vendor ID
HardSPL 3.28 - Communication Error
JumpSPL - Does nothing...

What am i missing?

[kristoff_sz]

What am i missing?

Interpreation and sense of what you are reading.

[socalkevin21]

http://hpcmonex.net/olipro/KaiserUnlocker.zip

That is the link to the Kaiser Unlocker by Olipro. It Hard-SPL's and SIM Unlocks. If you do not need the sim unlock simply flash to a different ROM after the first step.

[Puff1911]

Thanks socalkevin21 for providing a usable response :cool:

[socalkevin21]

Not a problem, let me know if you have any issues.

[Puff1911]

The software says to unplug the USB connection as soon as the screen turns to the three coloured screen.

when i plug back in, the progress bar waits a couple seconds then jumps directly to 100%.. is that correct?

The phone reboots, and starts back up as normal.. but the same version ROM is still there..

[mbarvian]

The software says to unplug the USB connection as soon as the screen turns to the three coloured screen.

when i plug back in, the progress bar waits a couple seconds then jumps directly to 100%.. is that correct?

The phone reboots, and starts back up as normal.. but the same version ROM is still there..

enter bootloader (press and hold the camera button all the way while pushing the stylus into the reset hole)

you should now be at a tri-color screen

what does this screen say?

[Puff1911]

KAIS130 MFG
SPL-1.0.OliPof
CPLD-8

when I click on Unlock Radio, it says "incompatible device"

Is that also normal?

Do i need to patch the radio as well?

[Puff1911]

wooooo!!! got it! i eventually got it to update the radio by clicking the button over and over..

I didn't get to unlock the phone (step 3).. but after i tried to update to windows mobile 6.1.. and it worked!

Thanks socalkevin21 and mbarvian!!

[Puff1911]

Well my device runs a lot faster.. but also sticks a helluva lot more!

Also my camera doesn't show anything, it takes pictures fine.. but there is no live display.. anyone having that problem?

And i also lost Voice Commander.. anyone have the install files for that?



**Fixed the camera problem. I had installed the HTC camera patch... Problem solved after removing it.**

[DaveShaw]

Well my device runs a lot faster.. but also sticks a helluva lot more!

Also my camera doesn't show anything, it takes pictures fine.. but there is no live display.. anyone having that problem?

And i also lost Voice Commander.. anyone have the install files for that?



**Fixed the camera problem. I had installed the HTC camera patch... Problem solved after removing it.**

Try a new HardSPL.

WM6.1 freezes sometimes with the OliPof 1.0 Hard SPL.
All the latest Hard SPL's are here: http://forum.xda-developers.com/showthread.php?t=396922

There are no other differences between 1 and 3.* other than the version number - they both work the same (oh and no MFG in 3.*, but you won't notice that)

Ta
Dave