Hard-SPL for x7510 and some other useful releases

[cmonex]

ok, so you got it finally :)

this post deals with hardspl, the next one will deal with ROMs :)

Features:

- this is unsigned Hard-SPL and ignores CID too, so custom roms or dumped & reconstucted roms (and any htc rom update) can flash. but it enforces ATHE400 modelid (I patched it for that). so ATHE***** or ATHE100 roms will be rejected. ATHE400 or ATHE400** is accepted.
- also, this has SPL overwrite protection, so won't accidentally get overwritten. but if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package is also available here.
- if your x7510 gets stuck on booting OS, then I have another way to revert to stock SPL in the cases when warranty is needed, this is a new special feature of the overwrite protection!

Requirements:

- first, if you have x7500 or x7501, then do not flash this.
- to download a compatible hardspl package for x7500/x7501 go to the other Athena subforums.
- also, make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en
- finally, if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-center.mspx

Instructions:

1) download Hard-SPL package from attachment, extract to an empty folder.
2) you must Have Phone Synced with PC in Windows Mobile!
3) run x7510_HSPL365.exe
4) follow steps in the RUU, and check on the device for prompts after PC shows loading bar.
5) it should go to tricolour screen now and say 3.05-OliNex (3.05 is for SSPL version, the original SPL is 3.05.0000)
6) SPL flashes, device automatically reboots, job done.
7) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 3.65-OliNex (3.65 is for Hard-SPL version, the original SPL is 3.05.0000).

NOTE: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter bootloader mode to see version: with the device turned on, press and hold the camera button (ALL THE WAY IN) then press the reset button with the stylus tip, then release the camera button when bootloader tricolour screen appears.

NOTE 2: anyone having problems with the device entering SSPL automatically, please copy SSPL-Manual-x7510.exe from the SSPL-Manual-x7510.zip attachment to the device and run it. then once the screen is in SSPL, run RUU manually. i.e. you run the RUU on the PC, if it isn't obvious.

NOTE 3: do not use this RUU to flash anything else! this is only intended for flashing SPL's.

NOTE 4: flash stock SPL *only* if you need to return the phone for warranty. only use it as last step - after reflashing stock OS and radio. usage: run the hardspl exe but do not press Next yet then replace the RUU_Signed.NBH with the stock spl NBH (posted here too), then go flash.


enjoy! and if you are happy with the results, a donation is always appreciated to the first donation link in my signature ("To Cmonex" link). ;)

[cmonex]

1. customruu for x7510, grab it from attachment. use this to flash roms.
2. nbh building tool for x7510, in another attachment. just choose X7510 from device list to work with it.
3. some stock OS links (some taken from RUU some from dumped / reconstructed roms)

WWE (english) 19209: http://rapidshare.com/files/160439716/x7510_WWE_RUU_Signed_forATHE400.zip
WWE (english) 19217: http://rapidshare.com/files/160431134/x7510_WWE_19217_RUU_Signed_forATHE400.zip
GER (german) 19217: http://www.filedropper.com/x7510gerruusignedforathe400
CHT (taiwan chinese) 19209: http://rapidshare.com/files/159819583/x7510_CHT_RUU_Signed_forATHE400.rar and a mirror http://www.megaupload.com/?d=30L24D8W
NEW: WWE (english) 3.29.707 rom: http://rapidshare.com/files/169675908/x7510_WWE_3_29_707_RUU_Signed.zip
+ extrom for 3.29.707: http://rapidshare.com/files/173043400/3_29_707_extrom.zip

make a mirror for others too please if you can =)



NOTE: I haven't had some of these tested, please let me know if they all work fine

ohh, I also plan to port AP4 to x7510! =) maybe tomorrow.



enjoy! and if you are happy with the results, a donation is always appreciated to the first donation link in my signature ("To Cmonex" link).

[LTxda]

Beautiful work as always. :)

[sergiopi]

CMONEX.... I will be your supporter for the next presidential campaign!
Please give us a FULL 3.5 HARD-SPL also for ATHE100 owners, ;) to avoid the AP4 flashing , may be a single 1.2-3.5, with a dialog box to chose between 1,2 and 3.5 partition! :)

Athena owners Please DONATE (https://www.paypal.com/cgi-bin/webscr?cmd=_xclick&business=contactchan%40freemail%2ehu&item_name=General%20Donations&buyer_credit_promo_code=&buyer_credit_product_category=&buyer_credit_shipping_method=&buyer_credit_user_address_change=&no_shipping=0&no_note=1&tax=0&currency_code=GBP&lc=US&bn=PP%2dDonationsBF&charset=UTF%2d8) to CMONEX, she is doing a really good job for ATHENA, and she never has done a preview of the work to push donation BEFORE the release, she just released the tools, as free gift.

I donate for this tool, even if I am just an ATHE100 owner!

P.S.:

I just receive the paypal statement, it is PAYPAL *WINDOWSCEMO" !!!!
I think this stand for windows CE mod... something, but SCEMO in italian means.... http://www.youtube.com/watch?v=CyOsulfpdY0
CMONEX I agree! Windows IS DUMB!

[NanoRuler]

Hi Cmonex, mine is still fine and stable.

Thanks again for everything you've done for us! I owe you!

[cmonex]

yes there'll be a 3.5 standalone package soon for ATHE100. that's one nice idea of bundling both ATHE100 SPL's, I'll remember that when making it :)

btw that 3.5 SPL has a feature to accept OS of 0x410 NBH type, which was meant as the NBH type for 3.5 SPL ROMs, and that would of course not be accepted/flashed by 1.2 SPL, but that somehow got forgotten :( , so the SPL 3.5 roms are all still 0x400...
at least this mistake can't be made now for the ATHE400 SPL, the modelid feature is not something that can be forgotten about =P

thanks for the donation, really appreciated :D


PS: yes my paypal business name is Windows CE Mods - I don't speak italian so forgive me for the choice, hehe.

[robjhellis]

Thanks a bunch cmonex - hard-SPL flashed successfully on my x7510.

[smokieruff]

thanks a lot...works fine for me:):):)

[xacsx]

works :)

>> in german: http://www.xxacsxx.wg.am/ameo_16gb.html

if you want to build your own rom, please dont forget to put these *.dlls into it. >> http://www.xxacsxx.wg.am/SensorDLLs.zip there are needed for some apps and games, that use the g-sensors.

[saied 1]

hi
first thank you cimonex very very much
second links for wwe doesn't work ,both of them.

please fix them.

[cmonex]

hi
first thank you cimonex very very much
second links for wwe doesn't work ,both of them.

please fix them.

yeah I see the problem, it wasn't uploaded with collector account :( stupid rapidshare... will fix it soon

EDIT: fixed, again new links, now should be working longer :)

[xiumutou]

hoho
..........

[sergiopi]

hoho
..........

:confused: hoho means? sorry I don't understand..

[smokieruff]

it`s christmas time:D

[youmeus]

Brilliant work...your USD200 is on its way...will try this when I get home later!

Cheers

[Calcu]

OOOOOOOHHHHHHHH!!!!!!! Incredible! xDDDDD Thanks, thanks, thanks!
Now i'll begin to read and try to find HOW can i make an Spanish ROM for the x7510.. First of all i think a i need an original Spanish Rom no?
any idea of where to find it?
then i'll begin to read on how to make my rom.

Thanks!

[xtep]

Now i'll begin to read and try to find HOW can i make an Spanish ROM for the x7510.. First of all i think a i need an original Spanish Rom no?
any idea of where to find it?


I uploaded the original Spanish ROM (dumped) sometime ago. You can find it in this post: http://forum.xda-developers.com/showpost.php?p=2509550&postcount=60

[Calcu]

i've dumped myself this spanish rom (i've an spanish x7510 xD) but someone told me that we need "the original" rom not a dumped one...

[theseas]

I have flashed both versions of WWE x7510 posted on this thread. Both of them show the same specs on settings "about" and "device info".Has anyone comfirmed this?Even the rom date is the same.Also I have flashed the WWE clean rom of xacsx and still the same.And it is natural because he has used the same stock rom posted here.Cmonex maybe u have done a mistake and have uploaded the same file(?)Please check it out because the result will be tha we once we make a mistake we will make another one based on the first one like the clean WWE rom of xacsx if of course I am right.Thanx

[Tadeusz]

yes there'll be a 3.5 standalone package soon for ATHE100. that's one nice idea of bundling both ATHE100 SPL's, I'll remember that when making it :)

btw that 3.5 SPL has a feature to accept OS of 0x410 NBH type, which was meant as the NBH type for 3.5 SPL ROMs, and that would of course not be accepted/flashed by 1.2 SPL, but that somehow got forgotten :( , so the SPL 3.5 roms are all still 0x400...
at least this mistake can't be made now for the ATHE400 SPL, the modelid feature is not something that can be forgotten about =P

thanks for the donation, really appreciated :D


PS: yes my paypal business name is Windows CE Mods - I don't speak italian so forgive me for the choice, hehe.

Hi, CMONEX, Just sent you a donation. No: 5V8929312W355302M.
Bit late, as I was off for some time.
Could you give some info about how to use your tool to prepare our own ROM? What tool/kitchen can we use to mode the rom? Can it be Sogarth's kitchen, for example. If so then how to extract proper XIP for Athe400? Maybe my questions are not too good, but I am kind of noob in preparing roms.

[brucewilsonpa]

WWE (english) 19209: http://rapidshare.com/files/160439716/x7510_WWE_RUU_Signed_forATHE400.zip[/b]

Any chance this could be mirrored on a site other than Rapidshare -- I've tried a number of times to download it and the site keeps dropping my connection so I only get part of it then have to start over.

Thanks!

[cmonex]

Any chance this could be mirrored on a site other than Rapidshare -- I've tried a number of times to download it and the site keeps dropping my connection so I only get part of it then have to start over.

Thanks!


OK but could you recommend a site that won't shut down the file after a couple of days due to high number of downloads

[cmonex]

Hi, CMONEX, Just sent you a donation. No: 5V8929312W355302M.
Bit late, as I was off for some time.
Could you give some info about how to use your tool to prepare our own ROM? What tool/kitchen can we use to mode the rom? Can it be Sogarth's kitchen, for example. If so then how to extract proper XIP for Athe400? Maybe my questions are not too good, but I am kind of noob in preparing roms.


thanks, donation is much appreciated :)

you can use athena kitchen, of course with different base rom, and set modelid to ATHE400, this is very important. XIP handling is the same.

btw, modelid is correctly set if you use NBHUtil to pack NB file to NBH to make it flashable :) just select x7510 as the device

[cmonex]

I have flashed both versions of WWE x7510 posted on this thread. Both of them show the same specs on settings "about" and "device info".Has anyone comfirmed this?Even the rom date is the same.Also I have flashed the WWE clean rom of xacsx and still the same.And it is natural because he has used the same stock rom posted here.Cmonex maybe u have done a mistake and have uploaded the same file(?)Please check it out because the result will be tha we once we make a mistake we will make another one based on the first one like the clean WWE rom of xacsx if of course I am right.Thanx


ok, confirmed, somehow i uploaded 3.27.405 both times... the other one would be 3.12.405 just in case someone wants that, but that one is a beta.

I'll upload 3.29 too, soon :) (it's 3.29.707 and 3.29.110)

[NanoRuler]

Hi CMONEX,

Do you have any plans on porting AP4 to the x7510?

[cmonex]

Hi CMONEX,

Do you have any plans on porting AP4 to the x7510?

yep... but it turns out PK sent me the wrong kitchen... and he deleted the original AP4 one, lol, so it'll be a bit more fun :)

P.S: I somehow always missed you on IRC, hope next time I'll get more lucky!

[NanoRuler]

Aaah, but it is I who is lucky! ;-P

[theseas]

cmonex any news about wwe 3.29 rom?

[theseas]

cmonex thank u for uploading 3.29 rom.

[theseas]

Is opera browser included in 3.29 rom? Although the home button is assigned to start opera there's not any opera browser in programs folder.Also when u press home button an error occur s. Has anybody the same problem?

[nimble_nobbi]

Hi cmonex,
I tried to download the German ROM from Post #2
(GER (german) 19217: http://www.filedropper.com/x7510gerruusignedforathe400)
, but the link doesn't work. Can I get it from somewhere else?

Best regards

nimble_nobbi

[xtep]

Short history:

When I power my x7510, it shows the tri-color screen with no-text and then shows a white screen with the text "Loading . . ." and it keeps there forever.

Have I bricked my device? Please help.

Long history (details):

I have instaled HardSPL as said in this thread and tested that the version was ok on the bootloader screen. Then I started to test my own cooked ROMs (flashing them with the x7510Wrapper.exe). I had tested some ROMs with no problem on the flashing), but when I tried to flash the latest I cannot start bootloader.
I did it as usually: connected the x7510 to my PC, checked that active sync was detected the x7510, started x7510Wrapper and follow the steps to flash the ROM. The x7510 rebooted with the tri-color screen and then the white screen with "Loading . . .". Finally RUU loader finished with an error.

Then I tried to reboot my x7510, but it starst againg with Loading screen. I have tried to press camera button while reset, with the same result than if I does not press nothing. I have also tried to remove the battery unsuccessfully. If I press down volumen button while reset it shows the screen to restore factory default, but whatever I do, after reboot it returns to the Loading screen.

What can I do to solve this problem?

Thanks.

[theseas]

Short history:

When I power my x7510, it shows the tri-color screen with no-text and then shows a white screen with the text "Loading . . ." and it keeps there forever.

Have I bricked my device? Please help.

Long history (details):

I have instaled HardSPL as said in this thread and tested that the version was ok on the bootloader screen. Then I started to test my own cooked ROMs (flashing them with the x7510Wrapper.exe). I had tested some ROMs with no problem on the flashing), but when I tried to flash the latest I cannot start bootloader.
I did it as usually: connected the x7510 to my PC, checked that active sync was detected the x7510, started x7510Wrapper and follow the steps to flash the ROM. The x7510 rebooted with the tri-color screen and then the white screen with "Loading . . .". Finally RUU loader finished with an error.

Then I tried to reboot my x7510, but it starst againg with Loading screen. I have tried to press camera button while reset, with the same result than if I does not press nothing. I have also tried to remove the battery unsuccessfully. If I press down volumen button while reset it shows the screen to restore factory default, but whatever I do, after reboot it returns to the Loading screen.

What can I do to solve this problem?

Thanks.

hehe dont worry man. it has happened to me a lot of times not only with x7510 but with other devices too. You have forgottent to remove your minisd card. Remove it and the device should enter in bootloader mode normally.

[xtep]

hehe dont worry man. it has happened to me a lot of times not only with x7510 but with other devices too. You have forgottent to remove your minisd card. Remove it and the device should enter in bootloader mode normally.

Thanks a lot.

You are right, I forgot to remove the minisd card.

[cmonex]

Is opera browser included in 3.29 rom? Although the home button is assigned to start opera there's not any opera browser in programs folder.Also when u press home button an error occur s. Has anybody the same problem?


hmm, i think you need extrom to go with it, i'll upload that too.

[theseas]

hmm, i think you need extrom to go with it, i'll upload that too.

please cmonex upload it too as soon as possible because without it your rom is useless. Is this the newest rom that you have? I think you have a newer than this as you have told me. Thanx

[cmonex]

Hi cmonex,
I tried to download the German ROM from Post #2
(GER (german) 19217: http://www.filedropper.com/x7510gerruusignedforathe400)
, but the link doesn't work. Can I get it from somewhere else?

Best regards

nimble_nobbi

i will try to upload it to rapidshare instead. though you need to wait a bit... i hate my shitty upload bandwidth :/

[xacsx]

GER: Original Rom (German) with Original Extended Rom: (thx to cmonex (rom) and nimble_nobbi (ext_rom)) >> http://www.megaupload.com/de/?d=S31KYQRQ
i have put it together

[theseas]

Original Rom with Original Extended Rom: (thx to cmonex (rom) and nimble_nobbi (ext_rom)) >> http://www.megaupload.com/de/?d=S31KYQRQ
i have put it together

which rom version is the one u have uploaded xacsx?

[xacsx]

its the german rom.
i have asked somebody, if they could send me the extended-rom-files, to put an original extended_rom in the WWE-rom. nobody have done this

WWE-Rom incl. Ext_rom 3.29.707: >> http://filestore.to/?d=C6F70B3F2

[yangzeyan]

Thanks!
It's so good!

[robjhellis]

[QUOTE=cmonex;2852542]ohh, I also plan to port AP4 to x7510! =) maybe tomorrow.

Hi cmonex. Happy New Year. Did you get the chance to work on porting AP4 to the x7510? It would certainly make a number of us jump for joy to do more with our devices.

Thanks for your support for this forum.

[youmeus]

[QUOTE=cmonex;2852542]ohh, I also plan to port AP4 to x7510! =) maybe tomorrow.

Hi cmonex. Happy New Year. Did you get the chance to work on porting AP4 to the x7510? It would certainly make a number of us jump for joy to do more with our devices.

Thanks for your support for this forum.

Yes, I have been waiting for word on this rom...Pls tell us what is happening.

Thanks

youmeus

[Calcu]

hey! what about cmonex? is posting anywhere else ?

[Calcu]

One question... i want to start cooking, i read a lot and i think that with:
HTC RIE
WinHex 15.1
WinCE CabManager
Thememaker X
Thememaker McDeb

like xacsx, i can begin....

Only i need one thing... a new ROM in spanish, or i need to use one WWE and translate it to spanish? because i want to make one in spanish...

thanks!

[Calcu]

Ok, i think i can port an WWE rom to an spanish ROm changing the mui. it will be my first ROM, not a real Rom but my first "thing" xDDDD

lets try it.

[honeyz]

Hi cmonex, My x7510 is China orgirinal ROM. I want to change to WWE, English ROM.
How can I make ? Please help me
Thx cmonex so much

[berk_bear]

Hi cmonex, My x7510 is China orgirinal ROM. I want to change to WWE, English ROM.
How can I make ? Please help me
Thx cmonex so much


honeyz, just read messages in the beginning of this topic and follow instructions there... First of all you need to flash Hard-SPL (files attached to 1-st message) and then download WWE ROM image (links you can found in early messages) and flash it on your device. Read all comments in topic...

[honeyz]

honeyz, just read messages in the beginning of this topic and follow instructions there... First of all you need to flash Hard-SPL (files attached to 1-st message) and then download WWE ROM image (links you can found in early messages) and flash it on your device. Read all comments in topic...
Thank u very much. Can you give me a link WWE ROM ?
Thx

[berk_bear]

Thank u very much. Can you give me a link WWE ROM ?
Thx

WWE (english) 3.29.707 rom: http://rapidshare.com/files/169675908/x7510_WWE_3_29_707_RUU_Signed.zip
+ extrom for 3.29.707: http://rapidshare.com/files/173043400/3_29_707_extrom.zip

(it's official WWE-rom and extended rom (for autoinstalling programms), just taken from second message in this topic ;) )
See instructions for flashing and download Hard-SPL there: http://forum.xda-developers.com/showthread.php?t=441684

But you can flash more advanced WWE ROM from xacsx (when Hard-SPL was flashed). Read more: http://forum.xda-developers.com/showthread.php?t=459054

[cmonex]

hey! what about cmonex? is posting anywhere else ?

I was away for a bit... getting back on track now :)

[RedeyeAce]

Heya guys,
and for the uninitiated, what benefit will i get with the rom please? could be nice to have this in the OP. Back in the day when i used to mod my Wince phones we used to take out all the cack from phone providers to make the phones more stable and usable. Is this what this one does?

Thanks

[robjhellis]

I was away for a bit... getting back on track now :)

Hi cmonex, fantastic to see you back on this forum. Is the any chance that you could revisit the opportunity to port AP 4 to our 7510s over the coming weeks?

Thanks and regards

[csasek]

Thanks for doing this. I just bought a 7510 last night and was able to change it from Chinese to English. For some reason it doesn't recognize my SIM. It does recognize my Hong Kong SIM and my gf's China Mobile SIM so i think I'll just go to China Mobile and see what's up. Anyways, I just wanted to thank you and this forum for helping me with my HTC phones over the last couple years

[vasia01]

By mistake my X7500 flashed with x7510_3_05_stockSPL. Phone power on only in bootloader mode:
ATHE100
IPL-v1.00
ATHE100
SPL-v3.05.0000

How repair phone?

[skiokko]

I have an htc x7510 in spanish language, what do i have to do and download to flash it with the latest italian rom (the best, official or not) ? Obviously if the italian one exists, otherwise it will be ok the english one.
Where can i find istructions and files ? I'm searching ith this forum from a lot of time, but i'm really confused, sorry for my incompetence...

[Calcu]

Cmonex is back or no? xDDDD what about porting the AP4?

[Calcu]

i tried to make my Rom but i think that without a master with me, is impossible xDDD, they doesn't work.... :-(

[k0s]

couldnt use to HSPL the rom.
if i use the x7510_HSPL365 it wont establish a connection to the phone for updating the rom, means it doesnt restart the the phone into bootloader

if i run the sspl manual following error in cmd line:

Unbehandelte Ausnahme: System.UnauthorizedAccessException: Der Zugriff auf den Registrierungsschlüssel "HKEY_LOCAL_MACHINE\Security" wurde verweigert.
bei Microsoft.Win32.RegistryKey.Win32Error(Int32 errorCode, String str)
bei Microsoft.Win32.RegistryKey.CreateSubKey(String subkey, RegistryKeyPermissionCheck permissionCheck, RegistrySecurity registrySecurity)
bei Microsoft.Win32.RegistryKey.CreateSubKey(String subkey)
bei SSPLSecure.Main.Start()
bei SSPLSecure.Program.Main(String[] args)


thank you


edit:
i tried to copy the romupdateutility rapitool and enterbootloader files from another release. there it would restart the phone into bootloader but the error is then : 270 : update Error, file corruped

[cmonex]

couldnt use to HSPL the rom.
if i use the x7510_HSPL365 it wont establish a connection to the phone for updating the rom, means it doesnt restart the the phone into bootloader

if i run the sspl manual following error in cmd line:



thank you


edit:
i tried to copy the romupdateutility rapitool and enterbootloader files from another release. there it would restart the phone into bootloader but the error is then : 270 : update Error, file corruped


i assume you try running sspl-manual.exe on the phone itself. try a hard reset.

do not use other releases PLEASE unless you want to brick the device.

[k0s]

:eek: SHAME !

i did try running the sspl-manual on the pc :rolleyes:

it works perfectly now ;)

everything went fine and without any problems!

thanks for your work and effort!
k0s

[thintin]

Thanks to everyone for their work with these ROMS and associated tools, it is greatly appreciated.

I think I've read all of the posts re:flashing a new ROM to my XDA Flint, but when I ran the X7510 HSPL365 it checked the phone and reported the current ROM, then it offered the upgrade option and I continued, but when the progress bar appears it says the connection to the device was lost. But active sync is still connected so it is obviously lying!

Anyone else come across this?

[danise0325]

i use Hard-SPL 3.65 for my u1000 after that no open some one help me :(:(:(:(

[cmonex]

i use Hard-SPL 3.65 for my u1000 after that no open some one help me :(:(:(:(


u1000 is old athena, not athena 1.5... I can try to help, send me a PM

and next time read more carefully..

[cmonex]

Thanks to everyone for their work with these ROMS and associated tools, it is greatly appreciated.

I think I've read all of the posts re:flashing a new ROM to my XDA Flint, but when I ran the X7510 HSPL365 it checked the phone and reported the current ROM, then it offered the upgrade option and I continued, but when the progress bar appears it says the connection to the device was lost. But active sync is still connected so it is obviously lying!

Anyone else come across this?


is the xda flint a renamed version of the new athena?

if not, then do not try to flash this.

if yes, give me more details about the issue. any error code you got from the program?

[NeilM]

is the xda flint a renamed version of the new athena?

Yes- the XDA Flint is O2 UK's version of the Athena/ X7510, with a few customisations.

I successfully installed the Hard SPL on my Flint, and can now load any relevant ROM.

[dunkeljoanito]

all the RApid links are broken

[cmonex]

all the RApid links are broken

which one did you find to be broken? they seem to work for me

[thintin]

is the xda flint a renamed version of the new athena?

if not, then do not try to flash this.

if yes, give me more details about the issue. any error code you got from the program?

Sorry, I didn't see this reply, for some reason I didn't get an email notifying me about it grrrr.

I have tried this several more times, always with the same outcome. The bootloader screen comes up, then the screen goes grey and says 'loading...' and then the PC RUU reports ERROR [260]: CONNECTION. THE UPDATE UTILITY CANNOT CONNECT TO YOUR PDA PHONE...etc'

As stated previously, the Flint has an O2 ROM.

any solutions guys?

Phil.

[thintin]

Hello again.
Following advice I removed the Sandisk microSD adaptor from the miniSD slot in case this was causing the [260] ERROR. I ran the RUU again and this time the device didn't respond to the app at all, and after about 30seconds I get ERROR [202] CONNECTION

I'm wondering if performing a hard reset and then running the RUU will help?

Update. I eventually used the manual option described in post #1 and the ROM flashed successfully. I have now installed Mitchyprima's lite 6.1 ROM with no further problems. Great big thank you to all involved in this project, it is greatly appreciated ;-)

[dunkeljoanito]

which one did you find to be broken? they seem to work for me

WWE (english) 19217: http://rapidshare.com/files/16043113...forATHE400.zip

NEW: WWE (english) 3.29.707 rom: http://rapidshare.com/files/16967590...RUU_Signed.zip
+ extrom for 3.29.707: http://rapidshare.com/files/17304340...707_extrom.zip


I can't download any of these ROMs... jejej srry any megaupload link?:D

[smuppy]

cmonex, you own. Simple fact.

One question though, I seem to have another version of SPL then you state as the original (3.07.0000, IPL 2.02), is there any way I can extract that easily and use as a backup in case I need to send the unit for service?

//Anders

[Xotic_X_tremist]

Anyone tried WWE 3.29.707???

[cmonex]

Anyone tried WWE 3.29.707???


yap, I flashed it to my x7510 no problem

[cmonex]

cmonex, you own. Simple fact.

One question though, I seem to have another version of SPL then you state as the original (3.07.0000, IPL 2.02), is there any way I can extract that easily and use as a backup in case I need to send the unit for service?

//Anders

if still interested, send me a PM and we can sort this. (need pdocread, pmemdump would only dump a corrupt image..)

[Xotic_X_tremist]

yap, I flashed it to my x7510 no problem

Thanks,I flashed WWE (english) 3.29 and works fine! What about extrom for 3.29.707??should I flash it to my device???

[qsworld]

Ok, sorry for my stupidity but I understand roms but what is a HardSPL? I love hacking my device but wanted to get a better understanding of what this does for your device.

Thanks
QsWorld

[cmonex]

someone asked me for 3.07 SPL dump... here it is, including IPLs

[cmonex]

Thanks,I flashed WWE (english) 3.29 and works fine! What about extrom for 3.29.707??should I flash it to my device???


yes strongly recommended as it goes with the OS nicely