Problems changing my number

[AMC_CAN]

I have been having problems changing my number on my phone. I am using DCD 3.3.4 and radio 3.42.50. I can not access the page where i can change my number on the phone. I have the number changed on the bell network. When ever i put the code in, ##564848#, the phone starts dialing. If i do ##564848 then it tried to load EPST and closes. I talked to bell IT and they gave me a link to get the factory bell settings rom.

http://www.pcdphones.com/phone_downloads.aspx?bid=76&cid=16&mid=298&carrier=Bell%20Mobility

I am using the new boot loader 2.47no2chem i believe. If i try to load the rom, will i run into problems? Does anyone know of a better way to change my number? Thanks for any help in advance.

Cheers,
Andrew

[mattsm]

I have been having problems changing my number on my phone. I am using DCD 3.3.4 and radio 3.42.50. I can not access the page where i can change my number on the phone. I have the number changed on the bell network. When ever i put the code in, ##564848#, the phone starts dialing. If i do ##564848 then it tried to load EPST and closes. I talked to bell IT and they gave me a link to get the factory bell settings rom.

http://www.pcdphones.com/phone_downloads.aspx?bid=76&cid=16&mid=298&carrier=Bell%20Mobility

I am using the new boot loader 2.47no2chem i believe. If i try to load the rom, will i run into problems? Does anyone know of a better way to change my number? Thanks for any help in advance.

Cheers,
Andrew

I was just talking about something similar over at geeks.
#codes do not work with some of the dialers.
Do not know if it will work, but find a dialer cab to install and retry. Worth a shot anyway.

I know this one has worked for me. http://forum.xda-developers.com/showthread.php?t=429179

[AMC_CAN]

Thanks for the link, ill try it out. They say to uninstall the previous cab how do you do that?

[AMC_CAN]

I also been reading around that i need to install a cdma dialer cab, and this might be the problem why i cant get into the EPST page. If anyone has any more ideas let me know.

I installed another dialer cab with no luck. I installed the cab from the link mattsm posted above with no luck. It tries to load the page and then closes. I was thinking, I installed a DCD 3.3.4 rom but was that rom intended for GSM phones or cdma? I think the settings page was removed from the rom. If anyone has any ideas please let me know. I want to install the rom from bell to get factory settings but i have a new boot loader, so will this be a problem? Thanks in advance

Cheers

[mattsm]

The only other thing I think you could try is qpst.
It lets you edit the epst settings from your pc.
you will need the qpst program, htc drivers
google the qpst and I will post some drivers you need in this post with an edit.
after you get the drivers intalled and qpst on your pc, You will enter ##3424# on you phone and hook up your usb to phone and it will install the drivers. Let me find the link to qpst help and I will post it as well. I am sorry right now I am busy but will post these before I leave.

[RyanMogul]

You can try my Diagnostic Shortcut CAB located in my HTC unlock directory, you dont even have to soft reset the shortcuts show up in programs/diagnostic folder.

There is also HTC windows drivers, Active sync 4.5, QPST 2.7 build 3.01 works perfect with TITAN, and many other tools. Plus instructions.

http://www.4shared.com/dir/13899878/aef6ea49/HTC_to_Windows_Drivers__Unlock_Tools.html

Start from ground up EPST change your number, MIN, anything you have to change to switch phone numbers. Then double check using PST and correct any settings. Let me know if you still have problems accessing PST with codes or shortcut. I will make you a Bell CAB that will fix your programming codes.

Enjoy!

[AMC_CAN]

Thanks alot for the help. I have to head to class right now but i will be back later today and try it out. When you say drivers, which drivers are you referring too? the drivers for my phone on vista? If you post some steps, i would greatly appreciate it. Thanks again.

[mattsm]

You can try my Diagnostic Shortcut CAB located in my HTC unlock directory, you dont even have to soft reset the shortcuts show up in programs/diagnostic folder.

There is also HTC windows drivers, Active sync 4.5, QPST 2.7 build 3.01 works perfect with TITAN, and many other tools. Plus instructions.

http://www.4shared.com/dir/13899878/aef6ea49/HTC_to_Windows_Drivers__Unlock_Tools.html

Start from ground up EPST change your number, MIN, anything you have to change to switch phone numbers. Then double check using PST and correct any settings. Let me know if you still have problems accessing PST with codes or shortcut. I will make you a Bell CAB that will fix your programming codes.

Enjoy!

thanks, He has the link. Got to go will check back later. Good Luck.

[RyanMogul]

Yes the HTC windows drivers get installed on your PC. Then QPST, then put the phone in Diag Mode, then plug it in with active sync usb connections disabled, then access Service Programming using QPST. The instructions (SPCunlockinstructions.txt) are on my share site, they will at least get you into Service Programming the rest is up to you.

Another thing I found is to disable driver signing in Vista press F8 while booting up and disable driver signing. Also if you do a search on XDA for HTC vista drivers you will find a thread with some drivers and information you can try.

[AMC_CAN]

Thanks alot RyanMogul6800. I have downloaded most of the files that you have mentioned. I can't try them out until monday, but ill give them a shot for sure. Thanks again. The Bell cab you mentioned, is that the problem? I can't seem to understand why in the dialer it tries to load the page and then closes as if it was missing. Let me know what you think.

Cheers,
Andrew

[AMC_CAN]

Thanks alot Ryan. I used the program and I changed my number with the qpst. It works now!!!

Cheers,
Andrew