Google's ION Android Build for HTC Kaiser - Questions and Troubleshooting Thread

[mburris]

This is the Questions and Troubleshooting Thread for the ION Build of Android for our Kaisers.

All Question Posts Will Need to Be Properly formatted so That You Can Be Helped More Expeditiously
Questions will be ignored until they have the proper info

Only Questions and Troubleshooting related content will be dealt with here.
All development related posts and updates will can be found here: Development and Downloads Thread. (http://forum.xda-developers.com/showthread.php?t=529734)

Before asking a question in your post, the following items will be required:
ROM
Radio
Carrier
Kaiser Model

See the second post for a correctly formatted example question

[mburris]

ROM: HappyTime Crazy Dragon V69
Radio: 1.65.24.36
Carrier: AT&T
Kaiser Model: KAIS100

I have an issue where I can't get google sync to work. How do I setup my APN?

[mburris]

Initial Troubleshooting if Android will not boot:

Flash with the suggested Radio and Rom
Format your SDCard and start over
Get a new SDCard and try that

[aggarath]

ROM: Hyperdragon IV IOlite
Radio: 1.71.09.01
Carrier: T-Mobile
Kaiser Model: KAIS120 (according to this (http://en.wikipedia.org/wiki/AT&T_Tilt#Versions))

I can't get data to work, I made a call and also made a data connection before starting Haret. I used all the files from the ION download thread (http://forum.xda-developers.com/showpost.php?p=4015874&postcount=1).
The modem keeps giving 'failed'. I also disconnected (no connection but to reset the modem) and tried to connect afterwards but no luck.
Otherwise it seems to be speedier and the graphics look better (maybe the resolution...)

[oscarbum]

ROM: PDACorner Ultimate X-V.8
Radio: 1.65.24.36
Carrier: AT&T
Kaiser Model: KAIS100

No internet connection either. Followed the instructions on HTCWiki for access point names and ran Togga. Nothing.

[SnootchieB]

ROM: Solace v3.1
Radio: 1.65.24.36
Carrier: T-Mobile UK
Kaiser Model: MDA Vario III/KAIS120

I have the same problem as above, i.e. Modem will not connect.

On launching the modem app (after setting up the APN), I get the message "PPP connection went down. Done". On pressing "Connect", I get the message "Starting pppd..." then after a couple of minutes "Connection attempt failed".

I always ensure I have a data connection open in WinMo before running Haret and have tried making a call before Haret as suggested by mburris. I swapped out the initrd.gz for one from a previous Okibi 1.5 build but, although modem connected, I couldn't sign in to Google, so I was no further forward.

[mburris]

For the three of you who are having connection issues:

Please make sure you are using the application called "Modem" instead of Toga.

Also if that still does not work, please delete your move your existing data.img file off the card, and try starting with the data.gz file. This will create a new data.img file. Having a fresh data file, designed for ION, will allow us to rule out any issues that may have been caused by a damaged data file.

[enatefox]

Can someone help me with themes? They come in an update.zip file. I try to overwrite the original images manually and it won't get past the boot logo. The permissions are all the same but do they have to be signed?

[khaytsus]

ROM: ROMeOS 4.6.0
Radio: 1.65.24.36
Carrier: AT&T
Kaiser Model: KAIS100

I must be stupid/newb, but the instructions say..

Step 1: Download the files:
-Download ExtractToRootOfSDCard.zip below and extract *everything* to the root of your SD card
-Download system.img from below and put it in the root of your SD card
-Download zImage from below and put it in the root of your SD card

....

Download the system.img file (then put it in the root of your SD card)
Download the kernel aka zImage (then put it in the root of your SD card)

Where's the "ExtractToRootOfSDCard.zip" file?

[mburris]

ROM: ROMeOS 4.6.0
Radio: 1.65.24.36
Carrier: AT&T
Kaiser Model: KAIS100

I must be stupid/newb, but the instructions say..

Step 1: Download the files:
-Download ExtractToRootOfSDCard.zip below and extract *everything* to the root of your SD card
-Download system.img from below and put it in the root of your SD card
-Download zImage from below and put it in the root of your SD card

....

Download the system.img file (then put it in the root of your SD card)
Download the kernel aka zImage (then put it in the root of your SD card)

Where's the "ExtractToRootOfSDCard.zip" file?

yeah... someone must be stupid/newb... unfortunetly, its the OP... check that post, I've updated it and the file you are looking for is actually attached now.

[loserskater]

ROM: Josh 6.5 Mayhem 2
Radio: 1.71.09.01
Carrier:AT&T
Model: Kais100

I cant get a data.gz to unzip. I know it takes a long time but ive waited for almost 30 min before giving up and soft resetting. Ive been able to boot ION using a data.img from a 1.1 or 1.5 build but cant get data working. any suggestions on getting a data.img made for ION to work?

[stringbean82]

If your connection fails on first attempt after setup, give it a reboot :) then it works

[aggarath]

For the three of you who are having connection issues:

Please make sure you are using the application called "Modem" instead of Toga.

Also if that still does not work, please delete your move your existing data.img file off the card, and try starting with the data.gz file. This will create a new data.img file. Having a fresh data file, designed for ION, will allow us to rule out any issues that may have been caused by a damaged data file.

As you can read in my post (http://forum.xda-developers.com/showpost.php?p=4016505&postcount=4), I used modem instead of togga.
After using a clean data file (the one that came with the ION files) I didn't even have togga.

Android tried unzipping the data.gz but failed (not enough room error; which is incorrect, there is plenty of room)
I extracted the data.gz by hand on windows and renamed it to data.img and put it on the sd-card.

Did that before posting yesterday, so it doesn't work (for me).


If your connection fails on first attempt after setup, give it a reboot :) then it works

I also tried that before posting yesterday but it didn't work.

[aggarath]

I will also post this here, it's in the android thread as well:

I still can't get data to work with the ION rom, steps i took:

Downloaded all the ION files.
Used a fresh data
Used the new intird.gz as mentioned in this post (http://forum.xda-developers.com/showpost.php?p=4019712&postcount=6014)
Removed the ppp setting from my startup.txt as mentioned in this post (http://forum.xda-developers.com/showpost.php?p=4019768&postcount=6017)

After each step I tried it again but the modem keeps giving me 'FAILED'

[mburris]

I will also post this here, it's in the android thread as well:

I still can't get data to work with the ION rom, steps i took:

Downloaded all the ION files.
Used a fresh data
Used the new intird.gz as mentioned in this post (http://forum.xda-developers.com/showpost.php?p=4019712&postcount=6014)
Removed the ppp setting from my startup.txt as mentioned in this post (http://forum.xda-developers.com/showpost.php?p=4019768&postcount=6017)

After each step I tried it again but the modem keeps giving me 'FAILED'

Well... try a different sdcard or maybe try the radio / rom combo from my first post... sorry its not working for you.

[SnootchieB]

For the three of you who are having connection issues:

Please make sure you are using the application called "Modem" instead of Toga.

Also if that still does not work, please delete your move your existing data.img file off the card, and try starting with the data.gz file. This will create a new data.img file. Having a fresh data file, designed for ION, will allow us to rule out any issues that may have been caused by a damaged data file.

@mburris...I was using Modem, as you can see from my original post. Have also tried a new data.gz, as this was mentioned on the main Android thread in the Kaiser Rom forum and still no joy.

If your connection fails on first attempt after setup, give it a reboot :) then it works

@stringbean...Rebooting has helped to resolve data connection problems with 1.1 builds, but had no effect with the Ion build.

I don't know enough about the Kaiser hardware to know whether this is relevant, but it strikes me as more than a coincidence that those reporting data connection issues in this thread all have the KAIS120 variant of the handset.

[mburris]

it strikes me as more than a coincidence that those reporting data connection issues in this thread all have the KAIS120 variant of the handset.

Ding Ding Ding...

what do you want to bet that DZO's got a KAIS100?

[garringm]

Rom: Hyperdragon IV
Radio: 1.65.24.36
Carrier: ATT
Model: ATT Tilt/Kais100

My phone wouldn't wake up this morning I plugged it in at 11:10 pm EST woke at 6:00 couldn't get phone to wake up

I also get this message after unlocking phone after every boot "The application Google Partner Setup (process com.google.android.googlespartnersetup) has stopped unexepectedly. Please try again." ......Force Close What is this and is it a problem with just mine I have tried reinstalling data.img doesn't go away started on the 2nd release of ION I may go back to the original release just for the fact my phone didn't lock up. Also is there an Advanced task manager that ION supports the one in Okibis will not work correctly I think this may be some of the reason phone starts lagging it is getting piled up with running apps and I have no way of closing them that I can find

[enatefox]

Rom: Hyperdragon IV
Radio: 1.65.24.36
Carrier: ATT
Model: ATT Tilt/Kais100

My phone wouldn't wake up this morning I plugged it in at 11:10 pm EST woke at 6:00 couldn't get phone to wake up

I also get this message after unlocking phone after every boot "The application Google Partner Setup (process com.google.android.googlespartnersetup) has stopped unexepectedly. Please try again." ......Force Close What is this and is it a problem with just mine I have tried reinstalling data.img doesn't go away started on the 2nd release of ION I may go back to the original release just for the fact my phone didn't lock up. Also is there an Advanced task manager that ION supports the one in Okibis will not work correctly I think this may be some of the reason phone starts lagging it is getting piled up with running apps and I have no way of closing them that I can find


Rom: AthineOS WWE (10/27/08)
Radio: 1.65.24.36
Carrier: Cingular
Model: ATT Tilt/Kais160

I'm getting endless process crashing for powermanager at boot and then periodically. I think there are serious issues with the power management-- just look at the root console and see the never ending list of debug messages about it. Packagemanager crashes when trying to install/uninstall software like Retro Clock or OpenHome2, etc.

Seconded on the Advanced Task Manager. It 'works' by seeing processes and services but applications is empty. I'd always clean out apps on bootup and then every 1/2 hour or so. Can't now and Android's not too efficient at closing processes. I know that you can set up a limit on running apps but that doesn't seem to be the best practice.

[aggarath]

Ding Ding Ding...

what do you want to bet that DZO's got a KAIS100?

AFAIK the KAIS110 vs KAIS120 only has a different camera and one extra.

Why did we not have this problem with 1.1?

[deekjx]

How do I get root from a terminal? When I su on this load, the password is no longer blank.

[nerdtaco]

ROM: Shifu's 6.1 V08 WWE Naked ROM
Radio: 1.71.09.1
Carrier: T-Mobile USA
Model: KAIS100

Is there any way to disable the box to require a SIM pin to use the phone? I can receive calls, send and receive texts, and use data, but I cannot dial out, nor can I view my SIM contacts. I've tried to unlock my SIM to dial out but it says that my SIM pin is incorrect even though it is the right pin. The SIM pin is disabled in WM and works fine.

Thank you

[bertbierhuis]

Hi,

Although i have made a good and working connection, trough the modem app, I can't log in to my Google account. I keep getting the message: 'You don't have a network connection.'

With my browser I can go to internet pages, tough... :confused:

Anyone with the same problem??

[afbcamaro]

loserskater change your radio to 1.65.24.36

[repvik]

ROM: Shifu's 6.1 V08 WWE Naked ROM
Radio: 1.65.24.36
Carrier: Netcom (Norway)
Model: KAIS130
(Just flashed rom/radio and hard-reset)

I can't get online. When I go to Settings-Wireless controls-Mobile Networks-Network operators, it says "error while searching for networks".
I can call out just fine, and I have a small signal-strength icon on the top line.

I removed the username/password/apn settings from startup.txt, and added APN in Android.

Where do I go from here? :)

(oh btw, is it possible to get Norwegian locale and keyboard layout?)

[nerdtaco]

I wasn't able to hear anything on either end so I switched to radio 1.65.24.36 and rom Hyperdragon IV Iolite. Now calls work, but I still can't dial out. Any suggestions?

[repvik]

Kindof solved it, I think. It worked when I opened Market for some odd reason.

[h0mer]

ROM: Solace 3.1
Radio: 1.71.09.1
Carrier: HTC
Model: KAIS100

Hi. I tried to boot Android and i got the following message (at the booting screen or whatever it is..):

Please wait... extracting Data Image
gzip: can't open '/sdcard/data': File exists
Failed
Failed to extract Data Image
/bin/sh: can't access tty: job control turned off

And after that the device just stops booting and freezes. What should i do?

[skola28]

h0mer, if I were you, I would format the SD card, and then only put the files listed in the first post on your card. This will start with a fresh data.gz (there shouldn't be a data.img file on the SD card until AFTER the first bootup)

[mburris]

Rom: AthineOS WWE (10/27/08)
Radio: 1.65.24.36
Carrier: Cingular
Model: ATT Tilt/Kais160

I'm getting endless process crashing for powermanager at boot and then periodically. I think there are serious issues with the power management-- just look at the root console and see the never ending list of debug messages about it. Packagemanager crashes when trying to install/uninstall software like Retro Clock or OpenHome2, etc.

Seconded on the Advanced Task Manager. It 'works' by seeing processes and services but applications is empty. I'd always clean out apps on bootup and then every 1/2 hour or so. Can't now and Android's not too efficient at closing processes. I know that you can set up a limit on running apps but that doesn't seem to be the best practice.

It sounds like you might have an SD Card issue.

What command, exactly are you using to "look at the root console and see the never ending list of debug messages"? I would like to try it and see what mine says.

[mburris]

Hi,

Although i have made a good and working connection, trough the modem app, I can't log in to my Google account. I keep getting the message: 'You don't have a network connection.'

With my browser I can go to internet pages, tough... :confused:

Anyone with the same problem??

Your question will be ignored until you edit your post to include the required information. See first post for details, or the second post for an example.

[enatefox]

It sounds like you might have an SD Card issue.

What command, exactly are you using to "look at the root console and see the never ending list of debug messages"? I would like to try it and see what mine says.
Not an SD card issue at all. It's with the build but there are 3rd party apps on my phone too but I hold that they should work. Maybe I'll one-by-one see if I can narrow them down. At least that will answer your question from the first page of this thread.

Get to the root console:
Fn+Left Softkey (on the keyboard not the faceplate)
Leave the root console:
Fn+Right Softkey (also on the keyboard)

The root console spits out debugging messages. 90% of them are battery or power related, maybe 5% is USB activity and the rest is whatever's left. This is also the console that is visible when Haret drops the initrd.gz into memory as if there aren't many debugging errors, you will still see the "Copying Applications" and "Android" marks from bootup. There was some major work done with power management and I believe (wild ass guess) that the devs that worked on it left them there to test but never removed them. Possibly assuming we wouldn't notice.

Nice that it leaves that shell open though.

[bullseye69]

ROM: Hyperdragon III january 13
Radio: 1.65.24.36
Carrier: Tmobile us
Kaiser Model: KAIS100

ok i guess i must be missing something. i get it to startup but it gets to the point that it failed to find the system.img file on sd card. is there anything else im to do other than put all the files on the root of the sd card.

Ok i got it to load into android. using a clean sd card. can some one help me out with why it wont detect the tmobile network. thanks
ok i also have another problem is i can't call out. and it fails to detect network. looked around and see its checked for use sim pin to make calls i have never set a sim pin up unless there is a default one.

[mikentucson]

ROM: Paradox_Extreme_Lite_V1.0
Radio: 1.65.21.14
Carrier: AT&T USA
Model: KAIS100

wanted to note phone everythings working (minus the usual.. wifi, bt, camera...) . at first i would type in my apn settings but it wouldnt save them. went under security & location -> and enabled use wireless networks. dont know if thats what made my apn settings stick or not but now they work and data & google sync works after toggle modem. only minor bug i noticed is i cant set my alarms. i change it from 8am to 5am but the settings dont stick

[drumboy03]

ROM: Shifu's 6.1 V08 WWE Naked ROM
Radio: 1.65.24.36
Carrier: AT&T
Kaiser Model: KAIS100 or KAIS110 (Both say AT&T Tilt in the Wiki, how do I know?)

So I have never been able to make it past the part where it tries to extract the data image. I've tried several different rom/radio combos. I've run android before and thought it was very cool, so I thought I'd try this new version, but I can' even get it to start now. Anyone have any ideas? I've Downloaded everything multiple times, and tried on multiple SD cards. Now I am only get the same error messages as everyone else. A little frustrating, is it just not ready for every model yet?

Damian

[briggs81]

ROM: Official 6.1 polaris rom
Radio: 1.59.44.02
Carrier: Fido
Kaiser Model: HTC Polaris :-P

Don't hate. Past kaiser owner, now Polaris owner, but very similar phones still!

Anyways, these ion files are working not bad on a lot of our polaris', but we are having a few issues. We don't have the developer power yet to tweak stuff so I thought I'd throw this out there, basically a general question.

For myself, I can receive calls and have a conversation no problem, and send and receive text messages, but I can't make any outgoing calls. As soon as i dial the number, the call ends right away.

Data connection does not work, but I know it can be picky so I'm not worried about that at the moment, but the not being able to make out going calls is reallly sucking. Does this ever happen to anyone?

A lot of us have tried different radios and roms and doesn't make a difference, for really any issues we have.

EDIT: Actually I see some Kaiser owners are having that problem too!

[JeckyllHavok]

Here my two cents:

ROM: HyperDragonIV Iolite
Radio: 1.71.09.01
Carrier: T-Mobile DE
Kaiser Model: HTC Kaiser / Kais 130
SPL: 3.29.Hard /Security Unlocked


Ok guys, for me i allways had to use a 1.1 build for syncing and the i can use it in all other builds. So no real problem with Data Connection.
Using latest ION Build, and i can sync my gmail, use market, browser, lastfm all works so far.
OpenGL apps like Neocore works, too.
Also i just get the ppp error just for one time, after another click on connect in modem it works...

This is my startup.txt i use for many versions:

set RAMSIZE 0x07000000
set RAMADDR 0x10000000
set FBDURINGBOOT 0
set MTYPE 1553
set KERNEL zImage
set initrd "\Storage Card\initrd.gz"
set cmdline "clock-7x00.mddi=0xa51 clock-7x00.ahb_div=4 clock-7x00.a11=528 board-kaiser-ts.PMAX=700 board-htckaiser.panel_type=1 ppp.apn=internet.t-mobile ppp.username=tm ppp.password=tm pm.sleep_mode=1 mddi.width=320 mddi.height=480 msm_sdcc.msmsdcc_fmax=32000000 no_console_suspend board-kaiser-keypad.atttilt=0"
boot




Great work guys

[JeckyllHavok]

Kaiser Model: KAIS100 or KAIS110 (Both say AT&T Tilt in the Wiki, how do I know?)

You see in Bootloader

[bullseye69]

ROM: Hyperdragon III january 13
Radio: 1.65.24.36
Carrier: Tmobile us
Kaiser Model: KAIS100

ok i have it booting fine into android and it finds my network as T-Mobile@@
i can send recieve text msg but cant make calls it ends them instantly. also cant get data working any help would be appreciated.
thanks
ok got data working except i cant get it to log into google to sync any ideas on this. thanks still cant dial out

[aggarath]

Would it help (I have no data) if I installed an older radio ?
I see a lot of people having the 1.65 radio.

[khaytsus]

yeah... someone must be stupid/newb... unfortunetly, its the OP... check that post, I've updated it and the file you are looking for is actually attached now.

:D Thanks!

[enatefox]

Vilord's new build has working wallpaper browsing. I'd still love to have Advanced Task Manager working. Is there something I can do to look into this?

[khaytsus]

ROM: ROMeOS 4.6.0
Radio: 1.65.24.36
Carrier: AT&T
Kaiser Model: KAIS100

Is it possible to boot Android more directly? I know we can't boot directly into Android, but is it possible to skip any WM startup and launch Haret? My own fault, but I have a bunch of Today plugins and it takes about 2 minutes for my phone to finish booting.

[enatefox]

I checked around the latest ION build and here's some things:
you can't 'su' with toolbox, use 'busybox su' and type 'vogue' for password
bash is missing
Terminal Emulator finally will save the font and color settings!

[Pandemic187]

ROM: shifu v08 full
Radio: 1.65.24.36
Carrier: AT&T
Kaiser Model: KAIS100 (I think)

Does anyone have GPS working on this, or on Kaiser in general?

[arjen888]

internet doesnt work for me either, this would be the only thing for me using android as my main os on my phone. I can't also change the font size in the spare parts menu which is really annoying.

Kais130
Windows mobile 6.5 by josh build 21819
Provider: Telfort The netherlands

greetzz

[repvik]

ROM: Shifu's 6.1 V08 WWE Naked ROM
Radio: 1.65.24.36
Carrier: Netcom (Norway)
Model: KAIS130
(Just flashed rom/radio and hard-reset)

Still the same setup. I was abroad this weekend. No matter what I tried, I could not get online with this build.
Anyone else have issues with roaming?

Edit: Oh, and it eats batteries like crazy! Isn't there any useful powermanagement working?

[Mystrorc]

Still the same setup. I was abroad this weekend. No matter what I tried, I could not get online with this build.
Anyone else have issues with roaming?

Edit: Oh, and it eats batteries like crazy! Isn't there any useful powermanagement working?

sleep mode 1 and turn off background syncing

[ruizit0]

is this bundle the most updated one ?

06/24/09 Combination of ION build from vilord and dzo files dzo android-kaiser-1.5-06252009.zip post #6006

http://www.androidonhtc.com/kaiser/latest_builds

[demanmethetplan]

ROM: dutty's wm6.1 wwe
Radio: 1.58.16.27
Carrier: T-Mobile Netherlands
Kaiser Model: KAIS120

I can't get data to work too, it hangs for a while at "starting pppd", then says "connection failed". i've set the correct apn etc in android->settings & in startup.txt . Also followed every step taken by Aggerath

[ruizit0]

ROM: 23 Jun 2009 - shifu V10 [NAKED]
Radio: 1.65.17.56
Carrier: TMN (portugal)
Kaiser Model: KAIS120 (i think acording to this http://en.wikipedia.org/wiki/HTC_TyTN_II)

i cant get data connection to... i tryed several ways...
with APN info in STARTUP, without it
i rebooted several times... tryed with an APN configuration inside ion..

doesnt work :S i think is because KAIS120 :\

[aggarath]

doesnt work :S i think is because KAIS120 :\

Which to me is weird because the difference (what I could find) is just in the camera's...
Maybe the code of this and 1.1 should be compared to see what the difference could be for the data connection...

[ruizit0]

Which to me is weird because the difference (what I could find) is just in the camera's...
Maybe the code of this and 1.1 should be compared to see what the difference could be for the data connection...

in last 1.1 i can get data and the last 1.5 from okibi i can get data to...
the only thing til now i cant do is sign in a google account dont know why :|

in this one i cant get any data :\

[wstraus]

I'm a little confused, I'm trying to update my kaiser (AT&T Tilt) to the latest Ion build. I'm currently running a bundle that came in a zip file called ExtractToRootOfSDCard.zip from a week or two ago. I'm looking at http://code.google.com/p/vogue-android/downloads/list wondering witch of these files I need if I just want to upgrade an already running Ion "install" Also can all of these files that are labeled as for the vogue also be used on the kaiser?

[enatefox]

the double post got me again

[enatefox]

I'm a little confused, I'm trying to update my kaiser (AT&T Tilt) to the latest Ion build. I'm currently running a bundle that came in a zip file called ExtractToRootOfSDCard.zip from a week or two ago. I'm looking at http://code.google.com/p/vogue-android/downloads/list wondering witch of these files I need if I just want to upgrade an already running Ion "install" Also can all of these files that are labeled as for the vogue also be used on the kaiser?
Get Vilord's latest builds. The zip on the front page here is outdated. ION runs on my Kaiser just fine.

data.gz: Don't need to download (will be recreated if missing automatically). Holds your settings, wallpaper, etc.
system.img: core Android image
initrd.gz: initial RAM disk, of importance to you is that it affects data, calls, etc.-- actual 'phone' stuff.

[mburris]

1'st post on dev thread updated with links to the newest files from vilord's google code page.

[Amaranthus]

ROM: Kaiser Stock 6.1
Radio: 1.65.21.18
Carrier: i wireless (US)
Kaiser Model: KAIS100

I'm not able to send/receive SMS or MMS. When trying to send it just says "Message not sent". I've got an APN setup for MMS. Is there any other configuration I need to do to get at least SMS working?

edit: Using the latest zImage, system-ion.img, and initrd.gz from vilord.

[bally3]

Apologies for the doubler post, but I dont think this going to get any time in the other android thread so I'm hoping someone here will help:

The latest build from google code gives me the following on my Polaris: "running an fsck on the SD Card
dosfsck 3.0.1, 23 November 2008, Fat32 LFN"

Its stuck at this for the last 20 mins. I have a Sandisk 4Gb SDHC card.

Any ideas anyone?

I've not been able to boot at all with the latest zimage and have been using dzo's april zimage-gpu before this to get it to boot but that crashed all apps.

[enatefox]

bally3, did you try a different card like a non SDHC?

[fuego3048]

ROM: PDA Corner Ultimate X2 V4
Radio: 1.65.24.36
Carrier: ATT
Model: KAIS100

Just wanted to post my stats so that way it may help someone. I am able to make a data connection. I have been able to sync my phone, access android market, make and receive calls, send and receive sms. Hope this helps someone.

[Amaranthus]

I switched to the 1.65.24.36 radio to see if that would help but I still cannot send SMS. I did discover I have been able to receive SMS this whole time though. Here is the output from 'logcat -b radio' at the time I tried to send a SMS.

D/RILJ ( 210): [0159]< SIGNAL_STRENGTH {4, 99}
D/AT ( 91): AT< @HTCCSQ: 2
D/GSM ( 210): SMS send size=2time=1246494254892
D/RILJ ( 210): [0160]> SEND_SMS
D/RIL ( 91): onRequest: SEND_SMS
D/AT ( 91): AT> AT+CMGS=17
D/AT ( 91): AT< >
D/AT ( 91): AT> 0001000b915121372917f2000004d4f29c0e^Z
D/RILJ ( 210): [0161]> SIGNAL_STRENGTH
D/AT ( 91): AT< +CMS ERROR: 500
D/RIL ( 91): onRequest: SIGNAL_STRENGTH
D/AT ( 91): AT> AT+CSQ
D/RILJ ( 210): [0160]< SEND_SMS error: com.android.internal.telephony.gsm.CommandExceptio n: GENERIC_FAILURE
D/GSM ( 210): SMS send failed

[aggarath]

in last 1.1 i can get data and the last 1.5 from okibi i can get data to...
the only thing til now i cant do is sign in a google account dont know why :|

in this one i cant get any data :\

Have you tried the latest files? They work on my kaiser.
Data works, calling in/out works, sms in/out works
Only thing I haven't tried is call waiting.

[bally3]

bally3, did you try a different card like a non SDHC?

I only have two sdhc cards unfortunately.. I'll try and get hold of one and give it a go.v Thanks for the reply enatefox :)

[enatefox]

I'm not sure why it should matter but I hacked my Wii and I can use an SDHC on the internal reader but can't use it with an external USB reader. It could be something that simple. Maybe there's a fix but I should think it's an issue with Haret.

[JeckyllHavok]

I'm not sure why it should matter but I hacked my Wii and I can use an SDHC on the internal reader but can't use it with an external USB reader. It could be something that simple. Maybe there's a fix but I should think it's an issue with Haret.

I think i can explain that: The possibility for reading SDHC Card is software sided. Every SD reader is "Hardware Sided" able to read and write SDHC. But the internal firmware must support it. On your WII i think you changed some software to get access for SDHC on the internal reader. But maybe the firmware of the external USB reader didn't support SDHC.

[enatefox]

On your WII i think you changed some software to get access for SDHC on the internal reader
Damn Wii mplayer devs and their selfless contributions

Are you saying that SDHC support (if that's the cause here) is something we could address or just sweep under the rug?

[Mudkip]

so is there a rom that will do data and allow me to use google sync?

[JeckyllHavok]

Are you saying that SDHC support (if that's the cause here) is something we could address or just sweep under the rug?

I think in our case it's another problem, maybe the used card. I'm using android on my Sandisk SDHC car with no problems, kaiser has an SDHC reader and android has the ability to use SDHC, too. Maybe the card is defect or it's not using standards? who knows..

[aggarath]

I think in our case it's another problem, maybe the used card. I'm using android on my Sandisk SDHC car with no problems, kaiser has an SDHC reader and android has the ability to use SDHC, too. Maybe the card is defect or it's not using standards? who knows..

My SDHC card also worked without problems, maybe it has something to do with the size? Mine is 4gb.

[pachuau86]

ROM: Anryl's 21725 WM6.5 Final
Radio: 1.71.09.01 eMO
Carrier: Vodafone
Model: KAIS120 (not sure, Swedish TyTn II)

Everythings running fine, but when the screen times out, and i turn the display back on, the display is all messed up (it gets blurry and there are lots of vertical lines on the screen) though it still works. Any help will be appreciated.

[knytphal]

ROM: PDACorner Ultimate X v5
Radio: 1.65.24.36 (also tried 1.71.09.01 previously)
Carrier: T-Mobile
Kaiser Model: KAIS100

Everything seems to working (minus the usual BT, Wifi, etc) except I am not able to make outgoing phonecalls. I can receive calls, but not make them. Tried the call voicemail from Windows Mobile trick before booting Haret but that's not making a difference.

In the past, I have been able to use an older system.img (I think....) and have outgoing calls work but I don't know how well that would work with this newer stuff. I did see over in the other Android thread that it looks as though there are issues with the way that T-Mobile initializes the card, so it looks as though I may be out of luck....?

[Amaranthus]

Update on my problem: Somehow I had the wrong SMS center number. It was actually missing a digit. Fixed it in WinMo and now SMS works just fine.

[aggarath]

ROM: Anryl's 21725 WM6.5 Final
Radio: 1.71.09.01 eMO
Carrier: Vodafone
Model: KAIS120 (not sure, Swedish TyTn II)

Everythings running fine, but when the screen times out, and i turn the display back on, the display is all messed up (it gets blurry and there are lots of vertical lines on the screen) though it still works. Any help will be appreciated.

http://www.androidonhtc.com/boot_options#board-htckaiser.panel_type

[pachuau86]

Thanks aggarath

[Mudkip]

ROM Shifu's 6.1 V10 lite
Radio 1.65.24.36
Carrier AT&T
Kaiser Model Tilt

I am unable to use sync. i have working data can make phone calls and receive them. I have edited my APN with the right settings for the HTC wiki for android.

[MOUSEY]

Here's my findings (After using for more than 2 weeks):-

ROM TPC Extreme v6
Radio 1.71.09.01
Carrier: Malaysia Maxis Mobile
Kaiser Model: KAIS100

SMS Send: OK
SMS Receive: OK
Dial out: OK
Receive calls: OK
Modem: OK
Marketplace: OK

Speaker Phone: Not ok
Battery Status: Not Accurate
Wake From Sleep:
pm.sleep_mode Set to 1 - Not ok
pm.sleep_mode Set to 0 - OK but battery becomes hot (drains like mad of course)...

I guess wake from sleep is a common problem. Anyone have a viable solution for that ?

[painreliever83]

Hi all, sorry to be posting on the wrong forum but all the Niki people who were developing Android appear to have moved on to other handsets and as the Kaiser and Niki versions of Android are similar I wondered if anyone here could help:

MODEL NIKI100
ROM US_NIKI_6.1_V1.0
RADIO 1.65.25.36
CARRIER Orange UK

I'm using the latest bootkit for Android on the Niki, as shown on the wiki

I have had this installed for a couple of days and it's running very well - calls, texts and internet all work ok but for some reason even though the internet's working, Marketplace etc are not, I keep getting a message saying "You don't have a network connection" when it tries to log me in, even if I've just been using the internet. I initialise my connection through the Modem app but it doesn't make any difference.

Anyone know how I can fix this? I've tried searching through both the Niki and Kaiser forums and haven't found any solutions...

Also it doesn't register the SD card

Thank you

[MOUSEY]

Here's my findings (After using for more than 2 weeks):-

ROM TPC Extreme v6
Radio 1.71.09.01
Carrier: Malaysia Maxis Mobile
Kaiser Model: KAIS100

SMS Send: OK
SMS Receive: OK
Dial out: OK
Receive calls: OK
Modem: OK
Marketplace: OK

Speaker Phone: Not ok
Battery Status: Not Accurate
Wake From Sleep:
pm.sleep_mode Set to 1 - Not ok
pm.sleep_mode Set to 0 - OK but battery becomes hot (drains like mad of course)...

I guess wake from sleep is a common problem. Anyone have a viable solution for that ?

I suspect the problem was due to the Auto Sync settings which was set to ON. I disabled it and VIOLA, it's still waking up from hibernation. Will keep on trying...

[NealCCM]

ROM : Official HTC (Arabic Enabled Rom) Ver 3.31.415.1 WWE
ROM Date: 09/03/2009
Radio 1.70.18.02
Carrier: Saudi Telecom Co., Saudi Arabia
Kaiser Model: KAIS130

Android Version: Android ION / 30.06.2009 (except the the zImage)
Call In/Out : Works Fine
Data / Google Maps / Market : Works Fine
Battery : Fantastic (With Background Data Disabled, Only 10% battery drain after 3-4 hours normal usage, without data connection)

In short, for me, everything is perfect, except one thing.
I am unable to use the latest zImage. If I use the latest zImage, it doesn't boot completely. It restarts itself just before showing the android splash screen.
The only working zImage is zImage-28-04-2009.

BTW, I have tried the following steps to rectify this issue, but sadly, to no success.

SDCards Tried:
SanDisk 2GB (both fat & fat32 formats)
Unbranded SDCard 1GB (both fat & fat32 formats)
Unbranded SDCard 256MB (both fat & fat32 formats)

ROMs Tried :
Solace v3.1
Ultimate-X.V7.Lite.2G
kaiser_wwe_shifu10_L
kaiser_wwe_shifu10_N
RUU_Kaiser_HyperDragon_IV_IOLITE_WWE_20090204

Any Suggestions ?

[painreliever83]

Hi all, sorry to be posting on the wrong forum but all the Niki people who were developing Android appear to have moved on to other handsets and as the Kaiser and Niki versions of Android are similar I wondered if anyone here could help:

MODEL NIKI100
ROM US_NIKI_6.1_V1.0
RADIO 1.65.25.36
CARRIER Orange UK

I'm using the latest bootkit for Android on the Niki, as shown on the wiki

I have had this installed for a couple of days and it's running very well - calls, texts and internet all work ok but for some reason even though the internet's working, Marketplace etc are not, I keep getting a message saying "You don't have a network connection" when it tries to log me in, even if I've just been using the internet. I initialise my connection through the Modem app but it doesn't make any difference.

Anyone know how I can fix this? I've tried searching through both the Niki and Kaiser forums and haven't found any solutions...

Also it doesn't register the SD card

Thank you

I managed to fix the problem myself, I deleted the data.gz file (I'd been using the one that came with the bootkit) and let it create its own one on boot. I had to redo all the setup etc but it solved both problems, I'm now able to access marketplace etc AND it now recognises the memory card.

Hope this info helps if anyone else is having the same problems.

Thanks

[Arura]

Hi,

Although i have made a good and working connection, trough the modem app, I can't log in to my Google account. I keep getting the message: 'You don't have a network connection.'

With my browser I can go to internet pages, tough... :confused:

Anyone with the same problem??

I also have this problem.

[urban69]

ROM: TPC Elite 6.5
Radio: 1.65.17.56
Kaiser model: KAIS130
Android: http://vogue-android.googlecode.com/files/android-1.5-2009-07-09.zip

I can't make any phone call, i got "call ended" after pressing the call button, but i can answer incoming call, and everything works! Is there any solution to this problem?

The second thing is problem with signing in to the google account to use ie. market, i've got internet connection, browser says i am not connected but websites are loading, pinging in terminal is also working, but settupwizard says that i haven't got network connection. Is there any possibility to enter this settings manually in some *.xml file? Or any fixes to that problem?

The last problem is that in example the term application isnt saving its preferences, i've modified /data/com.android.term/shared_prefs/com.android.preferences.xml to have a black background, but it will be nice to term app can do it on its own. What can be wrong that term can't save its preferences?

[zephxiii]

Very cool. How do i get sound notifications for sms? It shows nothing for me to select, i was able to select something for a ringtone through music player.
[EDIT: I forgot to extract the resources.zip heh]

Also, I can connect to the market place, but when I try to download an App, it just gets stuck at "starting download". Any ideas?

Also, I have a _cache and cache folder on my SD, not sure if that has anything to do with it.

ROM: AthineOS 6.1
Carrier; ATT
Model: KAIS100

[ihaveanidea]

i've tried to get Andriod to work on my HTC TYTN II Kaiser without bothering you guys...but i'm at my end of understanding and i need some advice on how to get the phone's audio and any audio and the wi-fi to work (i don't use the data ever)

KAIS130
FIDO
WM6

this was put on to a empty SD card (FAT32)
- from "android-1.5-2009-07-23"

zImage
system.img
initrd.gz
haret.exe
default.txt


(this is my default.txt file specfically)

set RAMSIZE 0x07000000
set RAMADDR 0x10000000
set FBDURINGBOOT 0
set MTYPE 1553
set KERNEL zImage
set initrd initrd.gz
set cmdline "clock-7x00.mddi=0xa51 clock-7x00.ahb_div=4 clock-7x00.a11=528 board-kaiser-ts.PMAX=700 board-htckaiser.panel_type=1 ppp.apn=ppp.internet.fido.ca ppp.username=fido ppp.password=fido ppp.nostart=1 pm.sleep_mode=1 mddi.width=320 mddi.height=480 msm_sdcc.msmsdcc_fmax=32000000 no_console_suspend board-kaiser-keypad.atttilt=0"
boot


Android loads up fine but the phone doesn't work properly and i have no wi-fi.

any fixes out there?

[zephxiii]

So has anyone been able to download apps off of marketplace?

EDIT: I ended up getting it to work by just starting over from scratch. I think I might have missed a "Agree to terms" popup the first time.

[milstanyu]

I installed Android successfully and have data working perfectly (can use browser to open web pages). However, when I try to log in to my Google account (in example, when opening Google Market, or Synchronize tool), after 1-2 minutes it says that I don't have data connection.

Any suggestion?

*** I fixed this myself. I added new APN with my carrier settings (only entered APN, username and password). Data works now both in browser and with Google servers. BTW my carrier settings are also in default.txt

[neutron939]

WM ROM: "3.29.409.0 NOR" (Official Norwegian Windows Mobile 6.1 ROM by HTC)
Radio ROM: 1.65.17.56
Android build: v1.5 released 07/23/09 on androidonhtc
Carrier: NetCom GSM Norway
Kaiser Model: Retail HTC branded kaiser (HTC TyTN II)
SDHC card: Sandisk 8GB, formatted with FAT32

I have just tested the 1.5 build of android released on 07/23/09 on my HTC TyTN II, and just want to share my experience in case someone finds this info useful.

I am using the default-kaiser.txt boot script, with the apn settings for my carrier entered.

What I tested that seems to work:

- Android boots, and I can browse through the menus and use all the programs that don't rely on any extra hardware or an internet connection (like the calculator)

- Both touch screen and the keyboard work. The buttons work, but aren't mapped as they "should be" in the final release (the windows button seems to act as an "enter menu" button, while the mail button seems to be a "back" button. End call button seems to put the device into standby)

- Battery meter works, but shows a different charge status than the WM battery meter. (Bug or not?) The battery meter also detects if the charger is plugged in or not.

- Sliding the keyboard in or out changes the orientation of the display correctly once the android has booted properly.

- Music player can play music through the loudspeaker at the back

- Music player can read MP3s located on the SD card outside the file system images.



What I tested that does not work / is bugged:
- Phone Calls don't work. I have not yet tried receiving a phone call.

- Data connection. I have entered the apn settings into the default.txt in WM before booting android, and into the APN settings within android. I have made sure that the data connection is up and working before booting into android. I have tried establishing the data connection with the "Modem" application, which just sits there for a while before failing. I have not yet tried to disable my PIN code to see if that gets around the problem, but I will do that later. (Other TyTN II users say they got it working without doing this)

- When powering the device back on from standby, I get lots of horizontal lines across the screen. Sometimes this is just a few annoying lines, with the screen still visible on the lines that are not effected, but other times it makes the entire screen completely unreadable. I have to reboot the phone and boot up android again to fix this.


You have done some great work so far guys. I hope this info helps you with your development and that one day we'll have a fully working android build for our TyTN IIs. So far it has been interesting to just be able to load the OS on my own device to take a look at its features :)

[thayneb]

ROM: AT&T 6 Mobile (Whatever AT&T put on the Tilt)
Kaiser 100(8925/Tilt)
Carrier: AT&T
Radio: 1.27.14.09


Let's see...
I was using the bundle from 07/09/2009
worked perfect except the other end of a phone call couldn't hear me.
Other than that it was perfect.

I got the newest bundle (07/23/2009). Works good, boots, send and receive texts just fine. Except, when I make a phone call the call is received but I can't hear the other end and other end can't hear me.... Then the phone won't allow me to end the phone call, it says the call in still in session even after the end has hung up the phone.... Any suggestions?

[zephxiii]

ROM: AT&T 6 Mobile (Whatever AT&T put on the Tilt)
Kaiser 100(8925/Tilt)
Carrier: AT&T
Radio: 1.27.14.09


Let's see...
I was using the bundle from 07/09/2009
worked perfect except the other end of a phone call couldn't hear me.
Other than that it was perfect.

I got the newest bundle (07/23/2009). Works good, boots, send and receive texts just fine. Except, when I make a phone call the call is received but I can't hear the other end and other end can't hear me.... Then the phone won't allow me to end the phone call, it says the call in still in session even after the end has hung up the phone.... Any suggestions?

Ya need to update your radio to 1.70.x something

[thayneb]

Updated to:

ROM: AT&T 6.1
Carrier:AT&T
Version: 3.57.502.2
Radio: 1.65.21.18

AND... Everything works great!
SMS (To and From) *CHECK*
Phone (Both Ends) *PERFECT*

so as far as service, everything is great.
good job guys!

[zephxiii]

just a quick note, if you disable Orientation in settings, it fixes the annoying 180 rotation when closing the keyboard. might be a good idea to have it off by default in the roms.

[thayneb]

How close are we to solving this wifi problem?
j/w.

[thayneb]

just a quick note, if you disable Orientation in settings, it fixes the annoying 180 rotation when closing the keyboard. might be a good idea to have it off by default in the roms.

thanks! =)

[adlaw]

ROM: TPC Elite 6.5
Radio: 1.65.17.56
Kaiser model: KAIS130
Android: http://vogue-android.googlecode.com/files/android-1.5-2009-07-09.zip

I can't make any phone call, i got "call ended" after pressing the call button, but i can answer incoming call, and everything works! Is there any solution to this problem?

The second thing is problem with signing in to the google account to use ie. market, i've got internet connection, browser says i am not connected but websites are loading, pinging in terminal is also working, but settupwizard says that i haven't got network connection. Is there any possibility to enter this settings manually in some *.xml file? Or any fixes to that problem?

The last problem is that in example the term application isnt saving its preferences, i've modified /data/com.android.term/shared_prefs/com.android.preferences.xml to have a black background, but it will be nice to term app can do it on its own. What can be wrong that term can't save its preferences?

Also can not make calls with the Radio: 1.65.17.56. Updated my radio to 1.71.40.02.eMo and still cant make calls. Downloaded the 23/7/9 and tried that with no luck. What is the best Radio for Android on the Kaiser?

[ljinsane]

Got Android working!!!

I am using the latest build from here:

http://www.androidonhtc.com/

[knytphal]

Also can not make calls with the Radio: 1.65.17.56. Updated my radio to 1.71.40.02.eMo and still cant make calls. Downloaded the 23/7/9 and tried that with no luck. What is the best Radio for Android on the Kaiser?

If you're on T-Mobile (also Rogers I think....) there is something with the way the SIM card is activated which causes us to not be able to make outgoing phone calls. The developers are working on it I believe. You can try older builds, it used to work just fine.

Of course, if you're not on one of those providers then it could be something else. I've read where people need to make sure they make one outgoing call in Winmo before running haret, or immediately making one outgoing call upon booting into Android.

[thayneb]

Every 5-6 hours, it crashes.
It doesnt start over. Nothing works
and force quit comes up when I try to
make any kind of call.

[pavlush]

When I boot from flash, Android sound/microphone works until the first call or playing first audio file. After that phone continues working well, but without any sound.
All other features ware working great. I have tried two latest builds (android-1.5-2009-08-08.zip and android-1.5-2009-07-23.zip) results are the same.

Please help how to resolve this issue.
Thanks.

ROM: dutty's WM6.1 WWE
Radio: 1.58.16.27
Carrier: AT&T (Unlocked, currently using other)
Kaiser Model: Tilt 8925

[gardndj]

Thought I'd give android a try this weekend and everything worked fine - android booted, data worked, played around with it for a little bit - until I restarted.

1. The phone now reboots into the bootloader. No amount of removing the battery and restarting has helped me to boot. If I pull the battery and then leave the phone off for an hour or two though, it will boot correctly into winmo. However, as soon as I soft-reset it goes back to the bootloader screen.

2. I tried flashing rom and radio, but it has no effect on the problem.

3. When I have the storage card with the android image inserted a message will briefly flash within the bootloader that says "No image file!". When the card is removed no message appears.

4. I haven't had a chance to get indepth with mtty.exe. It does not play nicely with Windows 7 and I won't have access to an XP machine for the next few days. I'll set up a VM tonight to see if that'll work.

I'm back to the trusty Q9H for the time being. Any suggestions would be appreciated.

[Andre_die_fifa_lusche]

ive got the vodafone wm6 rom,

android boots,but with my vodafone sim card it does not accept the pin (says it is the wrong one),sound is not playing,wifi is not working.

but anyway good job!

[solucionesjj]

Super excelente trabajo!! como puedo ayudar?
Super excelent job!! how to i can help?

[munch132]

how do i get the wifi to work it keeps saying that unable to connect to wifi and the modem doesnt work. PM me if anyone has answers.

[scramiro]

Sorry...

any one get solved about log in "Market" or "Sync" even getting internet connection? i can't see any answer about it...

Thanks a lot and great job!

[urban69]

any one get solved about log in "Market" or "Sync" even getting internet connection? i can't see any answer about it...

You should add APN in settings or by pressing menu in the settup wizzard.

[nooor7772000]

i do not have sd card with my tytn2 so how can i boot that from internal memory

[zephxiii]

i do not have sd card with my tytn2 so how can i boot that from internal memory

http://www.newegg.com/Product/Product.aspx?Item=N82E16820134809

[ms-kaiser]

1. The phone now reboots into the bootloader. No amount of removing the battery and restarting has helped me to boot. If I pull the battery and then leave the phone off for an hour or two though, it will boot correctly into winmo. However, as soon as I soft-reset it goes back to the bootloader screen.


Hi!

I have the same problem everytime I have to reboot or run out of battery, it sometimes works when the device has been connected to a computer for some time via usb. it also sometimes works after removing the battery for some time.

This behavior and what's displayed on the bootloader screen doesn't fit the scenarios described in the "kaiser stuck at bootloader" thread.

[nooor7772000]

http://www.newegg.com/Product/Product.aspx?Item=N82E16820134809

thanks sweet but i do not want to use sd card

[sruthika]

ROM: Hyperdragon IV IOlite
Radio: 1.71.09.01
Carrier: T-Mobile
Kaiser Model: KAIS120 (according to this (http://en.wikipedia.org/wiki/AT&T_Tilt#Versions))

I can't get data to work, I made a call and also made a data connection before starting Haret. I used all the files from the ION download thread (http://forum.xda-developers.com/showpost.php?p=4015874&postcount=1).
The modem keeps giving 'failed'. I also disconnected (no connection but to reset the modem) and tried to connect afterwards but no luck.
Otherwise it seems to be speedier and the graphics look better (maybe the resolution...)


Hi,

For those of you who cannot get data to work, please try the following :

Edit the default.txt file. Look for ppp.apn="some value". Change the value to the access point name for your service provider.

Save the file and boot into android again.

After booting into android, Press the start hardware button.
Select settings.
Select Wireless Controls
Select Mobile Network Settings
Select Access Point Names
Press the start hardware button
Select New APN
Type the APN name for your service provider
Save the settings

Now try to connect using mobile data and it will work. Its working for me perfectly.

Hope this helps.

[zephxiii]

I tried out the 9/11 build lastnight....great work with the wifi and GPS! I'm also thankful for the HTC Exchange integration, though it doesn't seem to sync calendar or contacts, a let down by HTC. I also like the resolution change from the 7-9-09 build.

But, there seems to be performance issues which make it kinda laggy to touch inputs, not all the time, but a lot of the time.

[ycode90]

Poor battery life . Phone gets HOT to the touch and won't wake after long sleeps. On a side note everything except camera and a few other minor items work . Good job so far .

[jw5801]

I have a TyTN II, running the most recent ION build. The only problem I'm having currently is that audio does not work anywhere. Ringtones don't make any noise and I can't hear anything during calls.

I'm new to this, so I'm not entirely sure what I should be posting, or what configuration I can actually make to fix this. Can anyone suggest anything I can try? Or suggest anything I can post to help with debugging.

[jw5801]

ROM: 1.81.710.1 WWE
Radio: 1.27.12.11
Carrier: Optus
Model: KAIS130 (I think)

Trying the most recent kernels and basefiles from here (http://code.google.com/p/vogue-android/downloads/list), but still not having any luck with audio. With some kernels the earpiece speaker works during calls, but I've never had the main speaker work (to play ringtones, menu noises, etc) and I haven't been able to get the microphone working during calls either.

[tyeo098]

@jw
make sure your ppp is set up. Phone would crash for me if it wasnt net up...

[lynj42]

Hi

Sorry to ask similar questions to previous posters, but i don't see anyone with my exact same phone/provider.

Rom: 3.28.161.1 WWE
Radio: 1.65.16.25
Model No: Kaiser
Provider: Vodafone UK

I've tried every dist I can find (7 to date) with combinations of
rootfs
system
zImage
initrd

The first time I put the ppp.apn stuff in the default.txt and then setup APN everything worked on the internet, but after a reboot it hasn't work again, despite trying all the stuff mentioned above.

I'm reluctant to flash the Rom/Radio, but if somebody can tell me this is the problem, then so be it?

Thanks for any help?

[lynj42]

Hi

Sorry to ask similar questions to previous posters, but i don't see anyone with my exact same phone/provider.

Rom: 3.28.161.1 WWE
Radio: 1.65.16.25
Model No: Kaiser
Provider: Vodafone UK

I've tried every dist I can find (7 to date) with combinations of
rootfs
system
zImage
initrd

The first time I put the ppp.apn stuff in the default.txt and then setup APN everything worked on the internet, but after a reboot it hasn't work again, despite trying all the stuff mentioned above.

I'm reluctant to flash the Rom/Radio, but if somebody can tell me this is the problem, then so be it?

Thanks for any help?

Re-installed original (latest) dist and wifi worked - for the first time.
Then tried internet (with & without wifi) and everything worked.
Then internet stopped working, including after restart.
Only then did it occur to me that the battery had now lost some of it's charge. It was @ about 60-70%, connected charger and bingo!
WM doesn't need such an amount of battery, so I hadn't thought Android would either, but it does.
Hope this helps anyone else who's had internet access come and go without anu other obvious reason?

[bvsoft]

Hi, I'm having the same sound problems. Lot of app's working but no soud what so ever.
My Kaiser 130 is orange nl branded and has radio 1.27.12.29 (orange nl has been taken over by T-mobile NL but no support from them nor from HTC)
If I flash this radio and the new one works in android (google ion) will it still work in windows mobile 6.0????
as long as I'm not sure of that I reluctant to flash the radio.

Phone details:
Kaiser 130 (Tytn II) Orange NL branded
R 1.27.12.29
G 22458807H
D 1.81.00.00

SPL 1.81.0000
CPLD-8