!!CRUX!! MUST READ!! LazyTool & HardSPL & 3 color screen solution before BRICK~~~~~~~

dioxda2 · Dec 22, 2007

!!CRUX!! MUST READ!! LazyTool & HardSPL & 3 color screen solution before BRICK~~~~~~~

20100130: post 2 updated

[size=+2]!!!!!!!!if you messed up with G3 & G4 model before flashing, your Prophet will be PERMANENTLY dead (unless a replace of mainboard +_+) DON'T TRY IT @ HOME !!!!!!!! [/size]

[size=+3]( DON'T forget TO HARDSPL YOUR DEVICE before flashing !!! )[/size]

20091204 update:

[size=+2]1. Lazy_Tool is for flashing all 6.1 and 6.5 prophet roms but NOT FOR VISTA or se7en operated computers.......2. VISTA FLASHING click HERE -- thanks to dear CLOUDYFA[/size] P.S. You can just replace the "*.nbf" FROM the UNZIPPED folder

WANNA FLASH FOR WM6 ROMS? please read @ end of post #1 ^_^ )

[size=+3] Additional RECOVERY steps for 3 colors screen boot-up after flashing...[/size][/color]

a. Force Bootloader Mode MANUALLY (see below Point 4 for How To ),

b. Then flash NVID - a AKU 2.* WM5 rom for recovering your Prophet.... ( P.S. the boot up screen will be changed to Qtek...)....^_^

**************************************

1: 3 coloured screen??????????? "DON'T PANIC",

2: 99.9999% CAN BE RECOVERED BY
DOWNGRADE TO WM5 WITH MANUALLY entering BOOT_LOADER MODE + flashing the NVID

3: IF USB CONNECTION ERRORS, TRY REMOVE BATTERY FOR 1 MINUTE and try again.

4: FORCE TO BOOTLOADER MODE MANUALLY HOW TO....

4.
4a. keep pressing the Commgr button and

4b. in the same time keep picking/sticking the bottom softreset button with stylus for one second,

4c. [size=+2][highlight] THEN ONLY ONLY RELEASE THE STYLUS[/highlight][/size] and wait for the screen
TO CHANGE to the three color screen (bootloader mode),

4d. then release all and go to step 10 below..... !!!

Steps to HARDspl your prophet

5. connect your prophet to computer (activesync done and Hardreset before so will be highly recommended !! )

5.1. In the Upgrade_HardSPL folder that you had downloaded AND UNZIPPED,
then look for the xxx.bat file and double click it (updated 20091114), all activities will only take 2-3 minutes and nothing will be seen in the Prophet screen.

(P.S. if connection Error, NO PANIC, soft reset OR remove battery for half a minute and try again.)

6. after the flash completed, it will restart automatically.

7. done!! in your prophet, nothing will be changed VISIBLY EXCEPT the digits IN the reboot screen !!!!!
and while booting now YOU MUST BE ABLE TO SEE information like:

Prophet Hard SPL isn't yet completed until the SPL shows

2.G3.4PDA (FOR G3 PROPHET) or 2.G4.4PDA (FOR G4 PROPHET)

(P.S. REPORTED !!! some device are not able to complete the CHANGE VIA Hardspl,
(like mine, NEVER TO 2.Gx.4PDA) if so, just flash the NVID then flash any 6.1 rom with LazyTool)

[size=+3]Tradition UPGRADE (OLD) method (for ROM with OS.nb )[/size].... ,

1. Connect to PC, activesync now OK, Flash with PVtemp or NVID for prophet for step 1

WHEN FINISH,

2. TOUCH NOTHING, HANDS-UP !!! leave it alone, just don't touch your prophet...... ( WM5 wwe flashing now finished)

3. [size=+2]ACTIVE SYNC WILL POPS UP soon, JUST DON'T TOUCH IT (disregard it) [/size],

4. THEN RUN UPGRADE.BAT from PC to flash to WM6 (should be included in your old ROM package with OS.nb )

5. follow the on screen steps and YOU WILL GET WHAT YOU HAD EXPECTED THEN~~~~~

[size=+2]
PLEASE REPLY IF YOU THINK HELPFUL ABOUT THIS MESSAGE !! ^_^
[/size]

P.S.

dioxda2 said:
@VISTA FLASHING click HERE -- thanks to dear CLOUDYFA

@ Lazy_Tool + Cloudyfa's 19213 clean rom , simple, fast, error free, a 2 in 1 upgrade package

if error persists while upgrading with this tool,

Please ask yourself...

I. did I softreset yet? did I make the Prophet recovery? (remove battery and sim card),
II. will the USB port of my PC currently too heavy loaded?

III. did I restart my PC yet?
IV. any connection related software other than activesync is running?

V. did I try the rear panel USB ports?
VI. is my PC currently too busy?

VI. did I try other USB cable yet?
VII. did I try the force bootloader manually before upgrade?

VIII. Did I hardreset my prophet after new flash(if everything had done but no help~~~~ ) ^_^
IX. Is the battery problems?

if anyone found this useful, please submit a simple reply..........

dioxda2 · Jan 7, 2008

all about dioxda2

~~~ What had happened to my first Prophet? pLEASE CLICK HERE

~~~All my cooked Prophet roms :

1d - Xtra Phrophet - 19214,
1b - U.C. Version - 19214,
1d - SPEED KING / Storm version - 19214 - Recommended!!,

2a - eXtreme PROPHET - 20270,
2d - ULTIMATE EDITION - 20270,

3d - Advanced version - 20273,
4d - with B/T Bug - 20275,
5d - buggy??? - 20721,

7d - THUNDER - 20748,
8d - eEXECUTIVE version - 20749 ,
9d - clean version - 20749,

1d - M2D-Lite - 20755,
1d- M2D 8Tabs version - 20755 - Recommended!!,
1d - m2d+mOtOsURF dual - 20755,
1d - SuperMarket version 1 - 20755 - Recommended!! for advance users,
1d CHINESE INPUT + M2D 7 tabs + 6 configurable iPHONE - 20755 - Recommended!!,

1d - cLEAN_tURtLE 1 & 2 - 20759 - for advance users only,
20755 - fINAL with iPhone?Today built - Recommended!!

WM6.5 - 1d - 21159 CLEAN n Fixed, for FUN,
WM6.5 CHS roms - 21806 / WM6.1 - 21127 for fun ,
WM6.5 CHS roms - 21222/21231/21502 for fun,

LAZYTOOL THREAD~~~

ufriendxda · Jan 7, 2008

HardSPL could sometimes not 100% perfect, as my experience. My Prophet stuck at Tri-color screen once after flashing a WM6 Rom, and I had to flash the official WWE AKU 2.2 Rom with IPL/SPL to set it to work.
SoftSPL method is more reliable, IMO.

dioxda2 · Jan 7, 2008

100% success in HardSPL upgrade......

ufriendxda said:
HardSPL could sometimes not 100% perfect, as my experience. My Prophet stuck at Tri-color screen once after flashing a WM6 Rom, and I had to flash the official WWE AKU 2.2 Rom with IPL/SPL to set it to work.
SoftSPL method is more reliable, IMO.

Please look here for reference..

1. if your device had been HardSPL successfully, the you can......

a. copy the 3 files ( in jumpspl.zip) to the root directory of the prophet
( JUST NEXT TO THE " \WINDOWS" FOLDER),

b. soft reset prophet,

c. run the SPL.lnk in the prophet,

d. then continue step 2 ( only 5 minutes..... finish.... so cool~~~~

)

100% success ~~~~

oko2600 · Jan 7, 2008

dioxda2 said:
Please look here for reference..

1. if your device had been HardSPL successfully, the you can......

a. copy the 3 files ( in jumpspl.zip) to the root directory of the prophet
( JUST NEXT TO THE " \WINDOWS" FOLDER),

b. soft reset prophet,

c. run the SPL.lnk in the prophet,

d. then continue step 2 ( only 5 minutes..... finish.... so cool~~~~ )

100% success ~~~~

I always do it like that...So quickly...

dioxda2 · Jan 7, 2008

Why Why Why???

oko2600 said:
I always do it like that...So quickly...

yes, you are right....

By the way~~~~~

Why no one read this thread before one is posting or shouting for help????????

ufriendxda · Jan 8, 2008

In fact, HardSPL isn't necessary to flash New WM6 Rom.
Just use SoftSPL, 100% OK.

dioxda2 · Jan 8, 2008

haha ^_^

ufriendxda said:
In fact, HardSPL isn't necessary to flash New WM6 Rom.
Just use SoftSPL, 100% OK.

Not about the necessity but.....

Hard SPL takes 3.5 minutes to flash completely,

but the old method......... PVtemp + Upgrade = ~30minutes....

just about the efficiency and the convenience... ^_^

ufriendxda · Jan 8, 2008

dioxda2 said:
Not about the necessity but.....

Hard SPL takes 3.5 minutes to flash completely,

but the old method......... PVtemp + Upgrade = ~30minutes....

just about the efficiency and the convenience... ^_^

Ok, let's put it in another way:
If our Prophet has IPL/SPL 2.××, just do SoftSPL before flash new WM6 Rom.
No need to flash HardSPL.
Is it not simple?

trxerz · Jan 8, 2008

dioxda2 said:
I saw many people here suffering from such cases.....

...
...
...

you've better.... ( FOR NEW METHOD)

1. After flashing hardSPL for g3 ( step 1) all went ok.

then BEFORE flashing/upgrading your Prophet to WM6,

please copy the 3 files from the jumpspl.zip to the root directory of
your G3 Prophet ( JUST NEXT TO THE " \WINDOWS" FOLDER,
(attachached, pease unzip and copy then paste)

2. UNPLUG YOUR DEVICE from PC,

3. Execute the SPL shortcut IN THE DEVICE, then you see a all bright or white screen,

Then plug back the USB port ( connect to computer) the device, THEN use the Rom Upgrade Utility (RUU) to the rom you like ( all activities can only be seen in the PC screen, nothing will be shown on the prophet....

4. Finally, after 100% ( at 85% may take to wait a bit longer, just be
patient, as it may look like hang for about 2 minutes) just wait, all will went
ok AND OF COURSE, after it auto-restart, ALL will be OKOKOK !!!

( better hard-reset for once more )

I am using a G3 too. Same experience before... ^_^

no more prolems!!!!!

The attached jumspl file is broken "can you upload the file again.
Thank's in advance

dioxda2 · Jan 8, 2008

???

trxerz said:
The attached jumspl file is broken "can you upload the file again.
Thank's in advance

Hey, the file works fine... just attached to this forum, not web

outside. I had tested it and download normal~~~

Please try again

trxerz · Jan 8, 2008

ufriendxda said:
Ok, let's put it in another way:
If our Prophet has IPL/SPL 2.××, just do SoftSPL before flash new WM6 Rom.
No need to flash HardSPL.
Is it not simple?

But if you want to back to the original ROM you need HardSPL

ufriendxda · Jan 8, 2008

trxerz said:
But if you want to back to the original ROM you need HardSPL

No, HardSPL is not needed to flash back to WM5 Rom.
Just put the Prophet into bootloader(Tri-color screen) and take RUU of WM5 Rom, will surely succeed, anytime.

megamix · Jan 11, 2008

How do you put spljump files to windows folder on the device when only the USB synchro mode (Red Green Blue screen) is displaying ?

EQUANCY · Jan 11, 2008

Nothing work.

I've patched hardspl
Jumpspl too
but
I can't install Wm6 rom
always stay bootloader mode.
there is no gsm no radio
only shows IPL and SPL ( 2.00 / 2.15 )

dioxda2 · Jan 11, 2008

I said......

EQUANCY said:
I've patched hardspl
Jumpspl too
but
I can't install Wm6 rom
always stay bootloader mode.
there is no gsm no radio
only shows IPL and SPL ( 2.00 / 2.15 )

Be patient!!

you must Hardspl sucessful ( SPL= 2.G3.4PDA .. something like this)

, or you cannot flash new methods,

please read through my content at the 1st page here....

or look to hma4 ......

I had made it easy for you... please folLow steps CAREFULLY

enjoy !!!

NO SHORTCUTS !!!!!

laca4025 · Jan 11, 2008

dioxda2 said:
Be patient!!

you must Hardspl sucessful ( SPL= 2.G3.4PDA .. something like this)

, or you cannot flash new methods,

please read through my content at the 1st page here....

or look to hma4 ......

I had made it easy for you... please folLow steps CAREFULLY

enjoy !!!

NO SHORTCUTS !!!!!

Yea, I must agree with Eqancy. Tried your method several times, the SPL says just what is should (2.G3.4PDA) but bootloader kicks in every time and nothing seems to work any longer.
Seems like I must be back to the old method.

EQUANCY · Jan 11, 2008

Nothing works still same!

There is only SPL 2.15 not anymore
I've tried everything but
Results are same.
I've Wm6 before but it was slow and I want to change rom.
and I've read to threads for how to.
I had earlier IPL 1.0 only that but rom was G4 version.
and it was very slowly.
and I've upgraded spl to 2.20
but after this upgrade I can nothing to upgrade
only Qtek's 2.20.7.34_2.20.7114_02.19.21 rom.
I've upgraded/installed Hardspl ( GSM version appears on bootscreen and HTC logo but still waiting )
And after this upgrade.
I did jumpspl too but...
every things same.
I will try again again again...
thanks.

dioxda2 · Jan 11, 2008

OKOKOK

EQUANCY said:
There is only SPL 2.15 not anymore
I've tried everything but
Results are same.
I've Wm6 before but it was slow and I want to change rom.
and I've read to threads for how to.
I had earlier IPL 1.0 only that but rom was G4 version.
and it was very slowly.
and I've upgraded spl to 2.20
but after this upgrade I can nothing to upgrade
only Qtek's 2.20.7.34_2.20.7114_02.19.21 rom.
I've upgraded/installed Hardspl ( GSM version appears on bootscreen and HTC logo but still waiting )
And after this upgrade.
I did jumpspl too but...
every things same.
I will try again again again...
thanks.

1. HARDspl OK,

2. then copy jumpSPL to the ROOT DIRECTORY OF PROPHET, NOT WINDOWS FOLDER,

3. UNPLUG PROPHET FROM PC,

4. RUN SPL.LNK IN THE PHROPHET,

5. PROPHET WILL WHITE SCREEN,

6. THEN PLUG usb TO A RESTARTED PC,

7. RUU UGPGRADE NEW ROM,

SHOULD WORK.....

EQUANCY · Jan 11, 2008

dioxda2 said:
1. HARDspl OK,

2. then copy jumpSPL to the ROOT DIRECTORY OF PROPHET, NOT WINDOWS FOLDER,

3. UNPLUG PROPHET FROM PC,

4. RUN SPL.LNK IN THE PHROPHET,

5. PROPHET WILL WHITE SCREEN,

6. THEN PLUG usb TO A RESTARTED PC,

7. RUU UGPGRADE NEW ROM,

SHOULD WORK.....

Successfully done
Thanks

!!CRUX!! MUST READ!! LazyTool & HardSPL & 3 color screen solution before BRICK~~~~~~~

Senior Member

Attachments

Senior Member

Attachments

Senior Member

Senior Member

Member

Senior Member

Senior Member

Senior Member

Senior Member

Member

Senior Member

Member

Senior Member

New member

Senior Member

Senior Member

Member

Senior Member

Senior Member

Senior Member

Similar threads

Top Liked Posts