Or Continue to Thread: [TWEAK](SIYAH/REDPILL/N.E.A.K.…
Find Your Device:
30th May 2012, 03:52 PM   |  #850  
geko95gek's Avatar
OP Recognized Contributor
Flag Establishing Battlefield Control... Standby!
Thanks Meter: 6,343
 
13,388 posts
Join Date:Joined: Dec 2010
Donate to Me
More
Cool CONFIRMED settings for SiyahKernel ICS v3.2.7.1 / v3.3.2 + CM9 and beyond
Ok, here we go as promised...

*** Again though, please be aware that these have not yet been tested thoroughly and some voltages may be too low for some of you... if that happens then please consult me here and I shall guide you. Also, be aware that some of you may have varied performance due to being on different ROMS and having different apps installed. Do not blame me if you don't get exactly the same results as me or someone else. PLEASE READ THE WHOLE POST!! ***

Also, to avoid being stuck. Please make a Nandroid backup before making any drastic UV changes. I will not be held responsible if your device turns into molten lava and burns a hole in everything it touches. Also, if you do have issues then please report them in this thread and consult with others instead of sending me private messages. Thank you!


-------

EXTREME UV VALUES


REQUIRED:

eXtweaks app and SiyahKernel ICS (v3.2.7.1 or v3.3.2 recommended)


SETTINGS (CPU):
  • GENTLE_FAIR_SLEEPERS = On
  • ARCH_POWER = On
  • CPU Hotplug = Default
  • CPU IDLE Mode = AFTR + LPA (default)
  • Smooth Scaling Level = 800Mhz
  • SCHED_MC = 2
  • CPU Undervolting = 100mV (all frequencies)
  • CPU Step Count = 18 (all available)
  • Default CPU Governor = pegasusq
  • Default CPU Scheduler = sio
  • Scaling Max Freq = 1000Mhz
  • Scaling Min Freq = 200Mhz

All other CPU settings as stock.


SETTINGS (GPU freq):
  • GPU Freq Step 1 = 40Mhz
  • GPU Freq Step 2 = 100Mhz
  • GPU Freq Step 3 = 200Mhz

SETTINGS (GPU voltages):
  • GPU Voltage Level 1 = 800mV
  • GPU Voltage Level 2 = 800mV
  • GPU Voltage Level 3 = 900mV

All other GPU settings as stock.


SETTINGS (other):

Screen settings stock. Vibration intensity = 3
Android logger enabled.

-------

LESS AGGRESSIVE UV VALUES


SETTINGS (CPU):
  • GENTLE_FAIR_SLEEPERS = On
  • ARCH_POWER = On
  • CPU Hotplug = Default
  • CPU IDLE Mode = AFTR + LPA (default)
  • Smooth Scaling Level = 800Mhz
  • SCHED_MC = 2
  • CPU Undervolting = -75mV (if you get reboots or freezes use -50mV)
  • CPU Step Count = 18 (All available)
  • Default CPU Governor = pegasusq
  • Default CPU Scheduler = sio
  • Scaling Max Freq = 1000Mhz
  • Scaling Min Freq = 200Mhz

All other CPU settings as stock.


SETTINGS (GPU freq):
  • GPU Freq Step 1 = 40Mhz
  • GPU Freq Step 2 = 100Mhz
  • GPU Freq Step 3 = 200Mhz

SETTINGS (GPU voltages):
  • GPU Voltage Level 1 = 800mV
  • GPU Voltage Level 2 = 800mV
  • GPU Voltage Level 3 = 950mV

All other GPU settings as stock.


SETTINGS (other):

Screen settings stock. Vibration intensity = 3
Android logger enabled.

-------

RELAXED UV VALUES


SETTINGS (CPU):
  • GENTLE_FAIR_SLEEPERS = On
  • ARCH_POWER = On
  • CPU Hotplug = Default
  • CPU IDLE Mode = AFTR + LPA (default)
  • Smooth Scaling Level = 800Mhz
  • SCHED_MC = 2
  • CPU Undervolting = -50mV (if you get reboots or freezes, use -25mV)
  • CPU Step Count = 18 (All available)
  • Default CPU Governor = pegasusq
  • Default CPU Scheduler = sio
  • Scaling Max Freq = 1000Mhz
  • Scaling Min Freq = 200Mhz

All other CPU settings as stock.


SETTINGS (GPU freq):
  • GPU Freq Step 1 = 66Mhz
  • GPU Freq Step 2 = 133Mhz
  • GPU Freq Step 3 = 267Mhz

SETTINGS (GPU voltages):
  • GPU Voltage Level 1 = 800mV
  • GPU Voltage Level 2 = 850mV
  • GPU Voltage Level 3 = 950mV

All other GPU settings as stock.


SETTINGS (other):

Screen settings stock. Vibration intensity = 3
Android logger enabled.


SETUP SCREENSHOTS (less aggressive UV values) (thanks to juzman for these):












BATTERY RUN SCREENSHOTS (used less aggressive UV values):







------- 30 MINS LATER -------







That was after a day of medium-heavy use on SiyahKernel v3.2.7.1 and CM9 Nightly 08-06-2012 (flashed in the morning, so didin't even let the ROM settle). Easily 6 hours screen on time guys, I'm sure you will agree that it could easily stretch past 7 hours if I let the ROM and kernel settle.

-------

That's it really, one other thing I want to mention is that I do not use auto-brightness (unless I am outside). Usually my brightness meter is at around 40% all the time.

If you guys could see how these settings go for you, if everything works as it should then the above information will be added to the OP.
Last edited by geko95gek; 30th August 2012 at 09:38 AM. Reason: added screenshots!
The Following 87 Users Say Thank You to geko95gek For This Useful Post: [ View ]