Apologies for the poor Translation (Google Translator)
Link to original thread.
http://www.htcspain.com/roms-lg-optimus-3d-384/kernels-bestia-2-acura2201-53297/
ALL CREDITS AND THANKS IN THIS THREAD SHOULD GO TO ACURA2201
Kernels Beast 2 BETA 3 Acura2201
Acura2201 GINGER ONLY
"" I'M MAKING A WEEK CALL NO GHOST. Hot Rod ONLY IN THE GROUP COULD CHECK THIS ONE WITH KERNEL.
THESE KERNELS SURELY NOT REMOVED THE GHOST CALLS, BUT OF COURSE IN MY CASE HAS THE minimized.
I WAS AN AVERAGE OF 7 OR 8 WEEK OF TIME 0 ""
Week Two no phantom calls
KERNEL BETA 3
I will upload these new self install Boot for testeis as you work. This is what has been modified for maximum performance with minimum power consumption, and above all I sought the maximum stability of the antenna signal to the phone's . reduced to the maximum the notches in the reproduction of music.
CPU
ADDED 4 NEW SPEED TO NUCLEUS KERNEL, NO MODULES NEEDED.
MHZ -100
-400 MHZ
-1100 MHZ
-1200 MHZ
MAXIMUM SPEED FOR SAFETY IS FIXED 1300 MHZ.
ALL THESE WOULD BE THE SPEED. 100 300 400 600 800 1008 1100 one thousand two hundred 1300 You can see that I added two intermediate speeds in low zone, ie 100 and 400, this is so to avoid sudden jumps between frequencies when the workload is medium-high and that the transition is more staggered and I much to adjust consumption. If you look at the graph you can see the reason for this change and will have the answer to why I did not add more fracuencias in uptown. In the high consumption jumps voltage is less pronounced than in the lower. An example: The frequency jump from 300 to 800 is about 0.7 volts, but between 1008 and 1400 rate of just 0.3 volts. I have set both consumption that only jump 1.2 to 1.3 is more pronounced, this is just to avoid blocking the phone with high workload and allows me to lower the voltage. ALLOW THE KERNEL RUNNING SPEEDS FROM MULTICARAGADOR, IF YOU HAVE THE MODULES verions 7.1 and Multiple V1 and V2.
TREATY HAS SIGNAL 3G and 2G INDEPENDENTLY.
SPEED IS SET IN THE MINIMUM CORE VOLTAGE AND ALSO. turns out that one of the first test I was to change the speed to 1200 MHz HSI series is 960 MHZ. The first time you need to change the signal frequency, I was hooked. What happened was this, black screen and I short circuited the battery in 30 minutes, not counting the cell phone I got to 43 degrees. At this point I realized where it was the fault of the baseband, the solution does not was to increase his speed, as I had already had these snags with kernel series, I had to do is the opposite, is to reduce your speed and avoid saturating the CPU with a lot of unnecessary information. The interruption of the kernel does not support more speed of 1000 MHz so the HSI is at 960, because my yours truly has combined an equation that at least on my phone, works perfect. Not to mention that consumption falls a bit silly and stabilizes the signal is much much much. As a paste it can happen that take a few tenths more on connecting with the market, which so far is the only application where I have noticed a drop in benefits ratio, but almost negligible. This could also be because, from the ramdisk I disconnected the use of dual-processor for web browsing. - MORE ADDED FROM ELIGIBLE Governors SetCPU - GET BE THE MAXIMUM TERM AFTER THE SECOND OR THIRD COMPLETE CHARGE CYCLE. - INSTALLING THE KERNEL TO THE MAXIMUM MOBILE BATTERY TO BE THE STATS batery PERFECT.
Before installing into "" Settings / About phone ""
and see if your kernel has a + at the end of these numbers.
2.6.35.7. if it has used the 1.8 + 1.8 But it has used
Bugs repaired: BETA 3 recalculated all voltages to avoid crashing and continuous bootanimation Added a new value in the version 1.2 now detects that SetCPU Fixed a bug in the RAMDISK instruction should go down much consumption now with the phone off charge but Animation is not the heats and
many other small details first test for 1.3 but will work well down to 1.2
KERNEL BETA 3 (28/04/12)
For the rom with the plus (+) in the kernel 1.3 Maximum speed
http://min.us/mbeHvK8stA
For the rom without the plus (+) in the kernel
1.3 Maximum speed
http://min.us/mcZLDwD1Q
For the rom with the plus (+) in the kernel
1.2 Maximum speed
http://min.us/mXGxAwuOF
For the rom without the plus (+) in the kernel
1.2 Maximum speed
http://min.us/mblbotU3ry
Alternative link for any one having problems with links above.
http://www.box.com/s/8d5d4091d279d24d09af
Link to original thread.
http://www.htcspain.com/roms-lg-optimus-3d-384/kernels-bestia-2-acura2201-53297/
ALL CREDITS AND THANKS IN THIS THREAD SHOULD GO TO ACURA2201
Kernels Beast 2 BETA 3 Acura2201
Acura2201 GINGER ONLY
"" I'M MAKING A WEEK CALL NO GHOST. Hot Rod ONLY IN THE GROUP COULD CHECK THIS ONE WITH KERNEL.
THESE KERNELS SURELY NOT REMOVED THE GHOST CALLS, BUT OF COURSE IN MY CASE HAS THE minimized.
I WAS AN AVERAGE OF 7 OR 8 WEEK OF TIME 0 ""
Week Two no phantom calls
KERNEL BETA 3
I will upload these new self install Boot for testeis as you work. This is what has been modified for maximum performance with minimum power consumption, and above all I sought the maximum stability of the antenna signal to the phone's . reduced to the maximum the notches in the reproduction of music.
CPU
ADDED 4 NEW SPEED TO NUCLEUS KERNEL, NO MODULES NEEDED.
MHZ -100
-400 MHZ
-1100 MHZ
-1200 MHZ
MAXIMUM SPEED FOR SAFETY IS FIXED 1300 MHZ.
ALL THESE WOULD BE THE SPEED. 100 300 400 600 800 1008 1100 one thousand two hundred 1300 You can see that I added two intermediate speeds in low zone, ie 100 and 400, this is so to avoid sudden jumps between frequencies when the workload is medium-high and that the transition is more staggered and I much to adjust consumption. If you look at the graph you can see the reason for this change and will have the answer to why I did not add more fracuencias in uptown. In the high consumption jumps voltage is less pronounced than in the lower. An example: The frequency jump from 300 to 800 is about 0.7 volts, but between 1008 and 1400 rate of just 0.3 volts. I have set both consumption that only jump 1.2 to 1.3 is more pronounced, this is just to avoid blocking the phone with high workload and allows me to lower the voltage. ALLOW THE KERNEL RUNNING SPEEDS FROM MULTICARAGADOR, IF YOU HAVE THE MODULES verions 7.1 and Multiple V1 and V2.
TREATY HAS SIGNAL 3G and 2G INDEPENDENTLY.
SPEED IS SET IN THE MINIMUM CORE VOLTAGE AND ALSO. turns out that one of the first test I was to change the speed to 1200 MHz HSI series is 960 MHZ. The first time you need to change the signal frequency, I was hooked. What happened was this, black screen and I short circuited the battery in 30 minutes, not counting the cell phone I got to 43 degrees. At this point I realized where it was the fault of the baseband, the solution does not was to increase his speed, as I had already had these snags with kernel series, I had to do is the opposite, is to reduce your speed and avoid saturating the CPU with a lot of unnecessary information. The interruption of the kernel does not support more speed of 1000 MHz so the HSI is at 960, because my yours truly has combined an equation that at least on my phone, works perfect. Not to mention that consumption falls a bit silly and stabilizes the signal is much much much. As a paste it can happen that take a few tenths more on connecting with the market, which so far is the only application where I have noticed a drop in benefits ratio, but almost negligible. This could also be because, from the ramdisk I disconnected the use of dual-processor for web browsing. - MORE ADDED FROM ELIGIBLE Governors SetCPU - GET BE THE MAXIMUM TERM AFTER THE SECOND OR THIRD COMPLETE CHARGE CYCLE. - INSTALLING THE KERNEL TO THE MAXIMUM MOBILE BATTERY TO BE THE STATS batery PERFECT.
Before installing into "" Settings / About phone ""
and see if your kernel has a + at the end of these numbers.
2.6.35.7. if it has used the 1.8 + 1.8 But it has used
Bugs repaired: BETA 3 recalculated all voltages to avoid crashing and continuous bootanimation Added a new value in the version 1.2 now detects that SetCPU Fixed a bug in the RAMDISK instruction should go down much consumption now with the phone off charge but Animation is not the heats and
many other small details first test for 1.3 but will work well down to 1.2
KERNEL BETA 3 (28/04/12)
For the rom with the plus (+) in the kernel 1.3 Maximum speed
http://min.us/mbeHvK8stA
For the rom without the plus (+) in the kernel
1.3 Maximum speed
http://min.us/mcZLDwD1Q
For the rom with the plus (+) in the kernel
1.2 Maximum speed
http://min.us/mXGxAwuOF
For the rom without the plus (+) in the kernel
1.2 Maximum speed
http://min.us/mblbotU3ry
Alternative link for any one having problems with links above.
http://www.box.com/s/8d5d4091d279d24d09af
Last edited: