my xperia mini buttons of back and menu leaving its silver chrome...am very tense...any1 tel me wat could i do to protect that silver chrome
i flashed minicm 2.2.0 and it couldn't lock the screen..i tried different lock styles but none of them worked..also the home button did nothing..and the strangest was that when they called me the phone didn't ring at all but in the call log i was able to see the missed calls
==> see what happens
- backup current state
- backup your contacts/sms the way you want
- wipe all your data, and do not restore any backup
- reinstall rom + gapps
make sure you are using 2.2.0+nAa11 too
I get the below lines in the S1Tool;
SELECT FIRMWARE PACKAGES
YOU CAN SELECT FEW PACKAGES WITH CTRL BUTTON
Am I pressing/clicking on something else while I hold the CTRL key down?
I'm using this S1Tool - http://xdaforums.com/showpost.php?p=25835757&postcount=698
hello everybody, after 2months with my awesome new miniCM7-2.2.0 i had a bad problem...the wifi isnt working anymore....any ideas?? it says it doesnt find any wifi, while i have one right by me, I havent changed any setting neither for the wifi connection, nor on my x10mini....i dont know what going on thnx for you help!!!
Yeah, been working from both of those threads. Thanks man.
---------- Post added at 09:15 AM ---------- Previous post was at 08:30 AM ----------
[Q] RE: Unlocking bootloader following - http://xdaforums.com/showthread.php?t=1254225
Does my X10 mini pro need to have stock SE ROM in order for this to work the 1st time?
I can't seem to find it in all the red if's, then's, but's, updated, outdated
When I go to unlock, the "plug USB cable" screen disappears, I remove finger from back key, then after a little time it jumps into MTP mode.
Into MTP-mode? You did turn off your phone before you pressed the back-button and connected the usb-cable didn't you?
And no, you don't need stock rom, just pay attention to the simlock-certificate warnings, if you've got an incompatible one your phone will stop working as a phone (no gsm/data, things like that)
Yeah, turned off. Even removed the battery for a couple of minutes. Still get the following(bit more detail);
This is the log I get from flashtool if I go through step 5c in post #1.
18/029/2012 15:29:59 - INFO - <- This level is successfully initialized
18/029/2012 15:29:59 - INFO - Flashtool Version 0.7.1.0 built on 2012-05-01 22:07:23
18/029/2012 15:29:59 - INFO - You can drag and drop ftf files here to start flashing them
18/030/2012 15:30:04 - INFO - Device disconnected
18/032/2012 15:32:40 - INFO - Device connected with USB debugging off
18/032/2012 15:32:40 - INFO - For 2011 devices line, be sure you are not in MTP mode
18/032/2012 15:32:40 - INFO - Device connected with USB debugging on
18/032/2012 15:32:41 - INFO - Connected device : U20
18/032/2012 15:32:41 - INFO - Installed version of busybox : BusyBox v1.19.1-cm71 bionic (2011-09-01 04:24 +0200) multi-call binary.
18/032/2012 15:32:41 - INFO - Android version : 2.3.7 / kernel version : 2.6.29
18/032/2012 15:32:41 - INFO - Root Access Allowed
18/038/2012 15:38:43 - INFO - Device disconnected
18/041/2012 15:41:04 - INFO - Please connect your device into flashmode.
18/041/2012 15:41:32 - INFO - Device connected in flash mode
18/041/2012 15:41:33 - INFO - Opening device for R/W
18/041/2012 15:41:33 - INFO - Reading device information
18/041/2012 15:41:33 - INFO - Phone ready for flashmode operations.
18/041/2012 15:41:33 - INFO - Flashing loader
18/041/2012 15:41:33 - INFO - Ending flash session
18/041/2012 15:41:33 - WARN - Cancelled
18/041/2012 15:41:33 - INFO - Device connected in flash mode
18/041/2012 15:41:35 - INFO - Device disconnected
18/041/2012 15:41:36 - INFO - Device connected in flash mode
18/041/2012 15:41:55 - INFO - Device disconnected
18/042/2012 15:42:00 - INFO - Device connected with USB debugging off
18/042/2012 15:42:00 - INFO - For 2011 devices line, be sure you are not in MTP mode
[/COLOR]After reading the 2nd last line of log, I thought the phones debug mode was NOT on in the phone but it is...
Hello guys!
A friend of mine has a problem: when it updates the kernel, the SIM card is not recognized. When he returns to the original kernel, back to normal?
Any ideas?
I'm now trying it on a different P.C (XP on a dell laptop - Previous attempts where on a Win7 box) to see if this gives me anything different. After a few failed attempts at getting the SEMC Flash Driver to load, it took after a bit of manual intervention. This is the output from s1tool.I am wondering which rom and kernel you are using at the moment. I see you're running an Android 2.3.7-version, and as far as I can remember, that version only works with custom kernels? If you already have a custom kernel you don't need to unlock your bootloader anymore.
I'm now trying it on a different P.C (XP on a dell laptop - Previous attempts where on a Win7 box) to see if this gives me anything different. After a few failed attempts at getting the SEMC Flash Driver to load, it took after a bit of manual intervention. This is the output from s1tool.
18/05/2012 7:17:02 PM Welcome to S1 tool.
18/05/2012 7:17:02 PM That is small and crippled subset of SETOOL2 service tool.
--<Snip>--
18/05/2012 7:17:33 PM RUNNING S1_EROM VER "R8A029"
18/05/2012 7:17:33 PM SOFTWARE AID: 0001
18/05/2012 7:17:33 PM LOADER AID: 0001
18/05/2012 7:17:36 PM FLASH ID: "0020/00BC"
18/05/2012 7:17:36 PM LOADER VERSION: "R4A045"
18/05/2012 7:17:36 PM
18/05/2012 7:17:36 PM MODEL (from GDFS): U20i
18/05/2012 7:17:36 PM SOFTWARE VERSION: 1235-3411_2.1.1.A.0.6
18/05/2012 7:17:36 PM CUSTOM VERSION: 1238-8804_R4B
18/05/2012 7:17:36 PM FILESYSTEM VERSION: WORLD-1-8_2.1.1.A.0.6
18/05/2012 7:17:36 PM SERIAL NO: CB511RV7GA
18/05/2012 7:17:36 PM
18/05/2012 7:17:36 PM SEMC SIMLOCK CERTIFICATE
18/05/2012 7:17:36 PM Elapsed:12 secs.
18/05/2012 7:18:21 PM PROCEDURE STOPPED BY USER
Same results on the laptop... Though I do now have a lower case 'r'
Short story, I used 'msm7227_semc.cmd' and put my fingers in my ears as I watched it go about it thing
By ticking and unticking everything a few times randomly, I probably triggered the random flag to update correctly, thus fixing the blinking color. Now I can select a color and have it blink normally.
you may first need to choose speaker, and then handfree to route radio correctly (may happen each tile the radio is started...)
With CM7 I need a ext partition? I have a standard 2GB card with the X10 MINI and I did not do anything with partitions, is that ok?
there is an app2sd storing to FAT feature.nAa's first post!!! said:App2sd / Dalvik2sd compatible with 2.1 app2sd (storing to ext2/3/4 pre-existing partition is detected and mounted as such)
Gingerbread's native App2sd (storing to fat)
Hi folks!
I have tried to find in this thread info on how to enable the sonyericsson version of android market, but i with no luck.
I reply to myself after getting help from matmutant.
I was looking for two different things: Getting the Sony Ericsson menu to the market, and enabling the Road Sync app that's free for SonyEricsson X10 mini users
To enable the SonyEricsson market, you need to edit the /system/build.prop file. Please be careful when you edit the file. If you mess up the file, you might get a phone that you can't boot (this can be fixed, cause i messed up a couple fo times I explain this later).
You can either just change the keys, or do like below: comment the old values with a # as the first char on the row, and write the new below.
Code:#ro.com.google.clientidbase=android-google ro.com.google.clientidbase=android-sonyericsson ro.com.google.clientidbase.yt=android-sonyericsson ro.com.google.clientidbase.am=android-sonyericsson ro.com.google.clientidbase.vs=android-sonyericsson ro.com.google.clientidbase.gmm=android-sonyericsson
For enabling the RoadSync app (or i guess any other app that want's to verify that it's running on a real SE-phone), then do these changes:
Code:#ro.product.model=X10mini #ro.product.brand=SE #ro.product.name=robyn #ro.product.device=robyn #ro.product.board=robyn ro.product.model=E10i ro.product.brand=SEMC ro.product.name=E10i_1237-0392 ro.product.device=SonyEricssonE10i ro.product.board=delta #ro.product.manufacturer=SE ro.product.manufacturer=Sony Ericsson
As I mentioned earlier, i messed up the /system/build.prop file at one point. To get this fixed, i just rebootet into recoverymode, and mounted /system. After this i could use adb (found in the android-sdk) to copy back an corrected build.prop (./adb push build.prop /system/build.prop)
I had also an other issue with the android-market app. It crashed and got stuck a couple of times, so i fixed this by uninstalling the recent update from manage applications->All->Market.
I hope my changes don't break anything for the CM7, so please if you know that CM7 needs any of these keys i changed in build.prop, then please inform me
To everyone who has the lockscreen crashing problem, just disable it.
Go to Menu > Settings > CM Settings > Tablet tweaks > Disable lockscreen.
Now it won't freeze, but of course you won't have a lockscreen, that could be fixed by downloading a custom lockscreen from market though
I can confirm that replacement Lockscreens from the market, such as WidgetLocker and Simply Lockscreen will work, so just follow my instructions to disable the lockscreen and then download a replacement one from the market, this will be a good enough workaround until nAa fixes the lockscreen reboot issue some of us are having.
21/ I notced weird behaviour of CWM recovery tool.
In some options, e.g wipe cache/factory data or install zip from sdcard i receive otpions like this:
- No
- No
- No
- No
- No
- No
- Yes
- No
- No
Could You fix it please
This is normal with CWM 4.x, this is to avoid that by mistake you choose YES if it have only 2 options!?!
That way, if you really want to apply YES it will be because you really want....
Hi,
I've been loocking in the forum this problem but I can not find it. >>> answered 2000 times, even after the answer being added here.
After unlock the bootloader, when the phone startup show a worng image with blue lines before show the boot animation.
24/ "portable wi-fi hotspot" works fine.
while Charging it keeps connected.
However, when not on charge, the phone turns to sleep and disconnects
Is there a way not to make it keeping connected when idle ?
waiting for a better answer... this one doesn't change anything since wifi hotspot and wifi are unrelatedSettings > Wireless & networks > Wi-Fi settings > Click the left button and choose advanced > Wifi sleep policy > choose never ( i think u chose never when plugged in )
I think that this is a common issue with CM7 and not just MiniCM7 (I experienced it on my DHD too).
Here is a small workaround for now:
Before sending the mms, disable data traffic, then enable it again and then send your mms.
You have to do it every time, before an mms but it is working for me.
Regards, D_d
i deleted chargemon but cwm 4.x can't mount sdcard!!!! please help!!!!!!
It is failing to mount sd-ext, script /etc/init.d/05mountsd is failing with:
I/mountsd ( 1160): /dev/block/mmcblk0 not ready, waiting 7 seconds...
I/mountsd ( 1164): /dev/block/mmcblk0 not ready, waiting 6 seconds...
I/mountsd ( 1168): /dev/block/mmcblk0 not ready, waiting 5 seconds...
I/mountsd ( 1172): /dev/block/mmcblk0 not ready, waiting 4 seconds...
I/mountsd ( 1176): /dev/block/mmcblk0 not ready, waiting 3 seconds...
I/mountsd ( 1180): /dev/block/mmcblk0 not ready, waiting 2 seconds...
I/mountsd ( 1184): /dev/block/mmcblk0 not ready, waiting 1 seconds...
E/mountsd ( 1189): SD not found (/dev/block/mmcblk0)
I added the following mknod lines to /etc/init.d/05mountsd:
#!/system/bin/sh
#
# mount ext[234] partition from sd card
mknod /dev/block/mmcblk0 b 179 0
mknod /dev/block/mmcblk0p1 b 179 1
mknod /dev/block/mmcblk0p2 b 179 2
BB="logwrapper busybox";
and it is working now
i modified the script and pushed it into the phone with adb: now everything is fixed!!!
this is a small guide:
download android sdk
download the fixed script and unzip it then copy it into the sdcard
launch a command line and To start the SDK Manager, please execute the program "tools/android"
./android
from the graphic menu install the platform tools
after the installal,go in the platform-tool directory and give theese commands
./adb remount
./adb shell
cp /sdcard 05mountsd /etc/init.d/05mountsd
then reboot the phone
now all apps in sd-ext partition are back!
DarkestPriest said:first, if you are not using stock ROM reflash stock ROM&kernel with SEUS then relock, re root etc ...
alternative (not validated for now)
with a root explorer app go to /system/app find CMScreenshot.apk ,
choose Install (replace) ,
system says trough a box: "APP not installed",
then Reboot and voila working again
Guys I don't see the MIUI battery bar change...how do I apply it???
Linkinsoldier said:
Linkinsoldier said:i removed my existing network and re-adding them solved the problem!
___________________________________here is my list:
(these first ones thanks to pedrocel and his optimal config thread)
DSP Manager
Gmail
Google Maps
Latitude
FOTA KILL (gOOGLE OVER THE AIR UPDATES)
Pico TTS (text to speech program/interface - if ypu arent blind u dont need it)
Voice Dial
Voice Search
(these others thanks to bojler in lets free up some memory thread)
androidian - 4MB - useless theme for me, which even isnt ldpi
browser - 320 kb - really bad browser, i use dolphin browser
calculator - i use realcalc
cmstats
cmupdatenotify useful if you want to be notified fr coming updates
cmwallpapers - 2,5MB
cyanbread - 3,6 MB also useless theme
dspmanager - always drains battery in background, and i really havent see any difference in playing music with it
email -1,5 MB - there are better alternatives
file manager - i use rootexplorer
latinime - 13 MB - i dont use this keyboard, its really too hard to use it on our devices, when you delete it, automatically is used standard multitap sony keyboard
livewallpapers - 3,8 MB if you dont use them you can delete this too
livewallpaperspicker you need it if you don't use quickpick ...
orangehaze - 1,7 MB - also, i don't use this theme
protips - that annoying android guy what is providing you tips on first boot after flashing
quicksearchbox 1,0 MB - i also dont use this, on mini pro, when opening keyboard on launcher, that search box launches.
soundrecorder - also, i use different apps for this purpose
genie widget
google books
weather and news (or newspapers, i dont remember the exact name)
an app called car home or something like that...
I think that's all
___________________________________
http://www.youtube.com/watch?v=-5-sxnx62-c
After many tests, I've found the best setting for my phone!
Use only grouping fixes OOM + bulletproof launcher script v6 supercharger, compcache kickasskernelizer standard 18% and tweaks!
The CPU is 600MHz!
I confess that I never had my phone as fast and as stable at the moment!
Back to share more news ...
Good combination with:
Spare Parts program:
Windows Animations FAST
Transition Animations FAST and this script http://xdaforums.com/showthread.php?t=1111145
Compcache 18%
More free space
with rootexplorer /system/usr/zi
delete the languages that you dont need.
system/usr/keyboard-config-languages-delete all languages that you dont need...
/system/fonts delete arabic(1.1mb)fallback(3.47mb)japannese(1.12mb)
/system/media/audio-delete all the sounds that you dont need..
i have done everything fine (unlocked bootloader and installed custom kernel) and made 2nd partition on SD card but when i open LINK2SD i`m getting trouble. sometimes it`s making script but after reboot i need to make script again and again. it can`t mount second partiton. what i have to do to get app2sd working?
The Sound icon on the Taskbar does not switch on and off the sound - it doesn't change the phone's state to silent, only vibrating, ringing or ringing with vibration. The other 3 icons work well - the BT, Wi-Fi and the GPS switch on and off with no problem, but the Sound and vibration... Why is that?
if you have problem with any widget button try a similar solving way
- settings > CyanogenMod Settings > Interface > Notification widget status bar i.e option 2 ("gestion de alimentation" in French) , > widget buttons (i.e option7),
- scroll nearly to the end to find sound (ring) modes,
- tick the options you need, then accept
- now it should work
>>> thk him for this pleaseafter little talk with one my friend we figure it out why in some provider is asking this code and in some not( like my case)
The reason is: This ROM is not legal I mean the original one from the Sony who before opening to users in theirs regions firs will be sent to operators , operators check it and then when you use for example Vodafone.de Vodafone.de if aprove the Sony ROM send a notification to users for a update is ON. When users updates their phone with the operator passed ROM they can be ''seen'' by the operator what type of phone with what type ot Android they are use and can send them auto setings like the APN MMS and etc.
If you want see the truelles of this just call your operator and ask them for auto APN . Try it if you have x10 mini with stock rom and with x10 mini with this one
In firs one operator say you : Ok i see in system you are using x10 mini vith android 2.1 i will send you the setings . But with this room she/he ask you what type of phone do you use bicoz I cant see it on system.
This is same wit the automated operator menus too : when you pres 4 (for example ) in voice menu and ask for a auto internet setings the autovoice say sorry we not support you phone yet will try again later.
This is not big deal for now bicoz the most of operators APN is already configuret but if you use operator who is not includet you cant use mobile data bicoz you not have APNs.
That is wy this code is asking for when you put some of providers sim some of them make theirs system in that way ... its more easy for them but for us is just annoing popup window
ro.telephony.ril_skip_locked=true
ETA: Estimated Time of Arrival i.e. when something is expected to arrive/be finished.
Go to Settings > Wireless & Networks > Wi-Fi Settings and press the menu button.BééHach said:i can't find my wifi network but some other are discovered by the phone, how to fix it?
Hi to denlille and all others,
to get Google Maps Precache working with x10mini / e10i
edit your /system/build.prop and add
Code:
ro.opengles.version=131072
I added that line above ro.com.google.locationfeatures=1
- reboot after editing and maybe
- delete app data of maps
Here is the link of the thread i found it:
http://xdaforums.com/showthread.php?t=1158183
Hi everyone, my 3g conection was really unstable and i delete this lines in build.prop:
ro.ril.hsxpa=2
ro.ril.gprsclass=10
ro.ril.hsupa.category=5
Now my data start inmediatly and the conection is stable again.
Ps: it may not work for all, because my 3g works on other freq bands.
50/ Hmm... So the new a2sd is essentially data2ext? Will I have problems upgrading as I'm on ext2, which is not supported?
Sent from my E10i using XDA App
Here's a brief explanation for A2SD/DC2SD/Swap:
A2SD/DC2SD only makes sense if you have /data that is over 200MB i.e. many apps.
Swap is useful if you need to run memory-hungry apps or wanna have more apps loaded in memory.
Any size for swap should be good depending on your needs (e.g. 128MB). To verify a2sd is loaded, run df via adb shell. It should show /data/app and /data/app-private mounted in /sd-ext.
Also /data/dalvik-cache should be mounted to /sd-ext/dalvik-cache if DC2SD is chosen.
To verify swap is used, try the command 'free' via adb shell.
None of the above are for the everyday/novice users. You have to know what you are doing.
explanation of http://xdaforums.com/showthread.php?p=22505939#post22505939 for dummies:
A2SD
What is a2sd?
It's other metod to save applications in SD.
How prepare your SD?
In Windows: Use http://www.partitionwizard.com/free-partition-manager.html or other tool partition. Create a ext4 partition in your SD.
In Ubuntu: Use gparted for create ext4 partition
How activate? (thanks to ferotakis)
1. Format SD and partiton it with CWM on phone make yor ext part and swap if yo want swap ig not live it 0
2. Install minicm7
3. Go to CM seting under performance put the a2sd (first show none till reboot)
4. Go to CM then hit apps and tick the "allow app moving to external "
5. Open terminal and type free
6. Go to CM again then performance again then to a2sd and chek there must no say NONE and must be a2sd
7. Install some apps then rootexplorer and browse in root dir on your phone you will saw ext folder open it and look your apps will be there
8. Thanks again if you missed to NAa
9. Learn some Linux
10. Go outside and show your fr and bbf your amazing phone
ashifr5 said:THANKS for this amazing kernel
but the problem is when i am using this with minicmpro v21 or minicm 7 2.1 the sensor which turns off the screen during call doesnt work! the screen keeps staying awake and whn it gets pressed with the cheek it turns mute/speaker
any help??