[Q] Problems flashing I9082 with any ROM

Search This thread
Hello, XDA.

I'm having some trouble using Odin to flash my brand-new chinese I9082.
I successfuly flashed CWM Touch 6.0.3.6 with Odin 3.09 and I'm able to access CWM through PWR+VOL.UP+HOME anytime I want.

However, when I try to flash any other rom I could find online, I get problems when NAND writing.

My Odin screen says:
Code:
[FONT="Courier New"][COLOR="Red"]ODIN MODE[/COLOR]
PRODUCT NAME: GT-I9082I_VE
CUSTOM BIN DOWN: Yes (6 counts)
CURRENT BIN: Custom
SYSTEM STATUS: Official[/FONT]

I've tried the following roms:
I9082ZNAMJ1_I9082CHUAMJ1_CHU (PDA only)
I9082XXUBMJ3_I9082ODDBMJ1_INS (PDA only)
I9082XXUBMGA_I9082XXUBMGA_SER (PDA only)
I9082XXUBMGA_I9082OXEBMGA_SER (PDA only)
I9082XXUBMF2_I9082OXABMF2_OXA (PDA, Modem, CSC, Boot and PIT)

During the first four attempts, I got the following Odin output:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082ZNAMJ1_I9082CHUAMJ1_I9082ZNAMJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!! 
<ID:0/003> FAIL!
<ID:0/003> 
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

During the last one (with all the files), I get the following output:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOT_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9082OXABMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9082XXUBMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003> 
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

And when I try to boot my phone, I get stuck at the splash screen.
What else can I do to flash my phone?

Thank you very much!

Best regards.
 

RVR

Inactive Recognized Contributor
Oct 29, 2012
1,756
1
2,882
Mumbai
rutvikrajagopal.in
Samsung Galaxy S7 Edge
Hello, XDA.

I'm having some trouble using Odin to flash my brand-new chinese I9082.
I successfuly flashed CWM Touch 6.0.3.6 with Odin 3.09 and I'm able to access CWM through PWR+VOL.UP+HOME anytime I want.

However, when I try to flash any other rom I could find online, I get problems when NAND writing.

My Odin screen says:
Code:
[FONT="Courier New"][COLOR="Red"]ODIN MODE[/COLOR]
PRODUCT NAME: GT-I9082I_VE
CUSTOM BIN DOWN: Yes (6 counts)
CURRENT BIN: Custom
SYSTEM STATUS: Official[/FONT]

I've tried the following roms:
I9082ZNAMJ1_I9082CHUAMJ1_CHU (PDA only)
I9082XXUBMJ3_I9082ODDBMJ1_INS (PDA only)
I9082XXUBMGA_I9082XXUBMGA_SER (PDA only)
I9082XXUBMGA_I9082OXEBMGA_SER (PDA only)
I9082XXUBMF2_I9082OXABMF2_OXA (PDA, Modem, CSC, Boot and PIT)

During the first four attempts, I got the following Odin output:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082ZNAMJ1_I9082CHUAMJ1_I9082ZNAMJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!! 
<ID:0/003> FAIL!
<ID:0/003> 
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

During the last one (with all the files), I get the following output:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOT_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9082OXABMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9082XXUBMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003> 
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

And when I try to boot my phone, I get stuck at the splash screen.
What else can I do to flash my phone?

Thank you very much!

Best regards.

first boot in recovery and wipe data /reset and then flash the firmware and make sure that only auto reboot and f.reset time is ticked
 
first boot in recovery and wipe data /reset and then flash the firmware and make sure that only auto reboot and f.reset time is ticked

Thanks for your reply!

I did that. after that, with the chinese rom, I got the following output:

Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082ZNAMJ1_I9082CHUAMJ1_I9082ZNAMJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!! 
<ID:0/003> FAIL!
<ID:0/003> 
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Then I wiped everything again and tried to repartition with baffin PIT file. Got this output:

Code:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port ....  0 
<OSM> All threads completed. (succeed 1 / failed 0)

But whenever I try to flash the rom, I get this output:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOT_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9082XXUBMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9082OXABMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> BcmBoot.img
<ID:0/003> NAND Write Start!! 
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)

By the way, I tried in two different computers but I have the same results in both.

Is there anywhere I can download a different PIT file to try it?
 

RVR

Inactive Recognized Contributor
Oct 29, 2012
1,756
1
2,882
Mumbai
rutvikrajagopal.in
Samsung Galaxy S7 Edge
Thanks for your reply!

I did that. after that, with the chinese rom, I got the following output:

Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082ZNAMJ1_I9082CHUAMJ1_I9082ZNAMJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!! 
<ID:0/003> FAIL!
<ID:0/003> 
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Then I wiped everything again and tried to repartition with baffin PIT file. Got this output:

Code:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port ....  0 
<OSM> All threads completed. (succeed 1 / failed 0)

But whenever I try to flash the rom, I get this output:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOT_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9082XXUBMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9082OXABMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> BcmBoot.img
<ID:0/003> NAND Write Start!! 
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)

By the way, I tried in two different computers but I have the same results in both.

Is there anywhere I can download a different PIT file to try it?

u dont need a pit file .....just uncheck repartition .........and make sure u do a data wipe before and after installing
 
u dont need a pit file .....just uncheck repartition .........and make sure u do a data wipe before and after installing

I only check re-partition when I'm using a pit file. The PDA-only roms didn't have "re-partition" checked but they also didn't work.
I'm guessing from the errors that my partition is somehow buggy, that's why I wanted another partition file (and I can't seem to find it anywhere).
 

I only check re-partition when I'm using a pit file. The PDA-only roms didn't have "re-partition" checked but they also didn't work.
I'm guessing from the errors that my partition is somehow buggy, that's why I wanted another partition file (and I can't seem to find it anywhere).
Thank you very much!

However, my problem looks persistent. After I repartitioned the cellphone with your file, I tried another rom and I got the following output:

Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082XXUBMGA_I9082OXEBMGA_I9082XXUBMGA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> vc-firmware.img
<ID:0/003> NAND Write Start!! 
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> BcmCP.img
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)

I can see the beginning of the progress bar in odin screen.
 

Top Liked Posts