Samsung s3 i9300 & Note2 N7100 & i9500 s4 Dead boot solution & imei null solution s3

Search This thread

jamesjerss

Member
May 5, 2011
49
171
Nagercoil
www.facebook.com
Samsung s3 i9300 & Note2 N7100 & i9500 s4 Dead boot solution & imei null solution s3

Samsung s3 i9300 & Note2 N7100 & i9500 s4 Dead boot repair solution & imei null solution only for i9300

Procedure:

* Download samsung s3 boot card maker Here

* Extract it on desktop

* Take a card reader insert memory card into the card reader nd connect it to the pc

* From the extracted folder run Diskdump2.exe

* Select generic storage Device. pictures below follw it



* Now to write the scripts folle the below given picr


picr.png


Now done yu are succesfully created Dead boot memorycard

To continue further

Requerments:

* Z3X samsung Box or SPT Box (i used z3x)

* special UART Cable (300k or 500k uartcable)

* Download teraterm-4.78 From
Here

* Fully charged battery

Dead boot Reapairing procedure

* Download nd extract teraterm-4.78 on desktop

* From extracted folder run ttermpro.exe there select serial port nd change the serial port to z3x serial
port lik below givin in the picr


M4u5ZqC.jpg


*After Select The Serial Port Press Ok Button den Go To Setup Click Serial Port Option
Select Baud Rate 115200 Then Press Ok Button lik below givn in the picr


mt7t.jpg

3mon.jpg



* Now insert the created boot card to the mobile

* Connect the Uart cable via z3x box

* Now Insert the battery nd wait for 5min if the procces didnt start discnnt the mobile close ttermpro agin try it.

* if it run success yu vil the result below given lik this.

pit_check_integrity: invalid pit.(0x0)
pit_check_integrity: invalid pit.(0x0)
update_guid_partition_table: There is no pit binary.
fsd_reclaim 1283: MST is not recognized(mst.magic=0x0)
fsd_reclaim 1284: MST is not recognized
fsd_reclaim 1599: Error(nErr=0x0)
fsd_reclaim 1604: j4fs_rw_start is set to default value(128KB)
j4fs_open 153: Error(nErr=0x40000000)
j4fs_read_file_bootloader 355: j4fs panic
load_j4fs_param: 'param.j4fs' does not exist, make new one..
j4fs_write_file_bootloader 184: j4fs panic
fail
j4fs_read_file_bootloader 355: j4fs panic
load_j4fs_param: debug level file does not exist..*INCORRECT!*
init_fuel_gauge: battery is not detected, do not init fuelgauge
init_microusb_ic: MUIC: CONTROL1:0x1b
init_microusb_ic: MUIC: CONTROL1:0x1b
init_microusb_ic: MUIC: CONTROL2:0x3b
init_microusb_ic: MUIC: CONTROL2:0x3a
PMIC_ID = 0x2
PMIC_IRQSRC = 0x0
PMIC_STATUS1 = 0x10
PMIC_STATUS2 = 0x0
PMIC_PWRON = 0x2
PMIC_IRQ1 = 0x27
PMIC_IRQ2 = 0x0
s5p_check_keypad: keypad value=0x0
s5p_check_reboot_mode: INFORM3 = 0 ... skip
s5p_check_upload: MAGIC CODE=d1b0f038
microusb_get_attached_device: STATUS1:0x3c, 2:0x0
s5p_check_download: update mode=0
j4fs_read_file_bootloader 355: j4fs panic
s5p_check_tzsw: invalid tzsw type! dummy?
scr_draw_image: draw 'download_error.jpg'...
j4fs_read_file_bootloader 355: j4fs panic
read_param_file: 'download_error.jpg' j4fs read failed!
fimd_div:13, div:1, FB_SOURCE_CLOCK:800000000, FB_PIXEL_CLOCK:57153600
a2, 60, 90,

* if yu get this error at the end [Patch Stop] This is not Rom Code. yu cant fix yur mobile yu have to change yur emmc chip

TN default
<OK>
<OK>
[DVFS] INT(1) : 0
DRAM Type : LPDDR2 8G
[DVFS] MIF(3) : 0
[EPLL][VPLL][CLK_DIV] OK
<OK>
[LOCK SW/HW]ARM:0/0 INT:0/0 G3D:0/0 MIF:0/0 SHIFT:0/0
[DVFS] ARM(0) : 5
[DVFS] INT(1) : 0
[DVFS] G3D(2) : 0
[DVFS] MIF(3) : 0
[SD_INIT
SDMMC_HighSpeedONE]
SD_READ: 20000 20000 0x40008000 -> 668484 usec
<OK>
Inp32(uAddr) : 0xea00007e
FW Booting
[Patch Stop] This is not Rom Code.

* After done this yur mobile must me n download mode or white screen if white screen manually put into download mode.

* After dead boot repair mine white screen i manually put into download mode pir below

AMqZJx9.jpg


* Now update your mobile with factory firmware with PIT file lik below given n the picr.Factory firmware Download Here

wDaOorh.png


* After update complete yur mobile may not have imei .imei null or yur mobile will not boot bcoz of dead boot repair. yur efs must be corrupted

* To Fix this prob first root yur mobile
Download from here (flash it through odin select as odin)

* Now Download this EfS repair file nd flash it through odin select as odin yur mobile must boot
but the imei become lik this 004999010640000

I9300_Repair_efs.tar.rar

vnEPYyC.png


* if yur imei is null yu cant repair using this box so 1st yu have to repair the efs using above givn file. if yur imei bcome lik tis oly (004999010640000) yu can repair using z3x or othr samsung tool

* Now follw the picr to repair imei problem.


8WTeetO.png

4hKIFxn.png

3tq4AvV.png


* After IMEI Repair

tGQBzTH.png


I hope this post wil helpful for lotz of dem
:laugh::laugh::laugh::laugh::laugh::laugh: :good::good:











 
Last edited:

neusys

Member
Jan 15, 2011
28
3
SP
Thank you for your great solution.

I have revive several i9300 by your solution.

But i have facing 1 big problem, the phone which i revive by this method only have Emergency Call after upgrade the firmware to official samsung 4,3 roms. phone was okay when under 4.1.2 firmware. (XXEMA2)

Imei is good n Serial is good. (Some phones have Serial 000000000).

another issue is Phone dun have product name under download mode.
 

jamesjerss

Member
May 5, 2011
49
171
Nagercoil
www.facebook.com
Thank you for your great solution.

I have revive several i9300 by your solution.

But i have facing 1 big problem, the phone which i revive by this method only have Emergency Call after upgrade the firmware to official samsung 4,3 roms. phone was okay when under 4.1.2 firmware. (XXEMA2)

Imei is good n Serial is good. (Some phones have Serial 000000000).

another issue is Phone dun have product name under download mode.


For Emergency Call fix run Samsung tool there repair/ run network repair

for serial nubr 000000 fix yu hav to repair baseband 1st try to write serial nubr using samsung tool or repair using asanam dongle.

Still same hardware issue may b
 

neusys

Member
Jan 15, 2011
28
3
SP
Well done. Thanks for your help again. All problem have been solved.

Do i need to create new memory card for note2 N7100 ?

is it the same procedure for note2 N7100 also ?
 

eatsleep

Senior Member
Jun 29, 2013
428
117
Hey Man (or more likely to be a woman :D )
Don't you think it is a bad idea to post your imei in public?
Bad things can happen
 

silverbox750

Senior Member
Dec 2, 2010
73
5
done all the steps but process wont start

i got dead s3 and i followed all the above steps and im using spt box for the final process but nothings happend.
i waited for 15 minuts,tried many times but same..?
any help..?
 
Mar 30, 2014
4
0
n 7100 with no rom

i have an n7100 that looks exactly as your s3 in the two pictures. when i turn it on it shows the exact scrambled image,and when entered in boot mode,this is what i get:
ODIN MODE (red)
PRODUCT NAME: GT-N7100
CUSTOM BINARYDOWNLOAD: No
CURENT BINARY:Samsung Official
SYSTEM STATUS: Custom
KNOX WARANTY VOID: 0
AP SWREV:

THAT IS THE EXACT MESAGE,NOTHING PLUS OR MINUS
when i flash whit odin,it sais no pit partition. i need help with the files and procedure
 

jamesjerss

Member
May 5, 2011
49
171
Nagercoil
www.facebook.com
i have an n7100 that looks exactly as your s3 in the two pictures. when i turn it on it shows the exact scrambled image,and when entered in boot mode,this is what i get:
ODIN MODE (red)
PRODUCT NAME: GT-N7100
CUSTOM BINARYDOWNLOAD: No
CURENT BINARY:Samsung Official
SYSTEM STATUS: Custom
KNOX WARANTY VOID: 0
AP SWREV:

THAT IS THE EXACT MESAGE,NOTHING PLUS OR MINUS
when i flash whit odin,it sais no pit partition. i need help with the files and procedure

yours may b a hardware issue . emmc chip problem yu hav to replace it
 
  • Like
Reactions: wani64

Dj-Abi

Senior Member
May 31, 2009
69
4
how to create sd card because i cant follow the photos because they are deleted . anyone tell me how ?
 

nassiry

New member
Apr 30, 2014
3
0
prablem

hello thank you for your help I have done everything that you have wroten but is give me error different like this


[LOCK SW/HW]ARM:0/0 INT:0/0 G3D:0/0 MIF:0/0 SHIFT:0/0
[DVFS] ARM(0) : 5
[DVFS] INT(1) : 0
[DVFS] G3D(2) : 0
[DVFS] MIF(3) : 0
[SD_INIT
SDMMC_HighSpeed:DONE]
SD_READ: 20000 20000 0x40008000 -> 440042 usec
<OK>
Inp32(uAddr) : 0x53525353
LINUX Bootingøq!?

---------- Post added at 10:53 AM ---------- Previous post was at 10:46 AM ----------

Hello thank you for your help I have done everything that you have wroten but is give me error different like this


[LOCK SW/HW]ARM:0/0 INT:0/0 G3D:0/0 MIF:0/0 SHIFT:0/0
[DVFS] ARM(0) : 5
[DVFS] INT(1) : 0
[DVFS] G3D(2) : 0
[DVFS] MIF(3) : 0
[SD_INIT
SDMMC_HighSpeed:DONE]
SD_READ: 20000 20000 0x40008000 -> 440042 usec
<OK>
Inp32(uAddr) : 0x53525353
LINUX Bootingøq!?[/QUOTE]


please help me I have 2 samsung galaxy s3 the same problem
 

zaclee

Member
Aug 17, 2010
32
1
The Pearl of the Orient
Hi, jamesjerss, first of all thx for sharing this information, it really help! thx agn. but now im facing some issue for N7100, for I9300 there is no any problem. when i use the same method for N7100, it will shwo up this error, kindly help.

pit_check_integrity: invalid pit.(0x0)
pit_check_integrity: invalid pit.(0x0)
update_guid_partition_table: There is no pit binary.
fsd_reclaim 1283: MST is not recognized(mst.magic=0x0)
fsd_reclaim 1284: MST is not recognized
fsd_reclaim 1599: Error(nErr=0x0)
fsd_reclaim 1604: j4fs_rw_start is set to default value(128KB)
j4fs_open 153: Error(nErr=0x40000000)
j4fs_read_file_bootloader 355: j4fs panic
load_j4fs_param: 'param.j4fs' does not exist, make new one..
j4fs_write_file_bootloader 184: j4fs panic
fail
j4fs_read_file_bootloader 355: j4fs panic
load_j4fs_param: debug level file does not exist..*INCORRECT!*
init_fuel_gauge: fuelgauge power ok
init_fuel_gauge: POR status
fuelgauge_por: POR start: vcell(3886), vfocv(3918), soc(66)
fuelgauge_por: update SDI parameter
fuelgauge_por: RCOMP(0x87), TEMPCO(0x930)
fuelgauge_por: POR finish: vcell(3887), vfocv(3951), soc(61)
get_table_soc: vcell(3887) is caculated to t-soc(67.89)
init_fuel_gauge: start: vcell(3887), vfocv(3951), soc(61), table soc(67)
init_fuel_gauge: finish: vcell(3887), vfocv(3951), soc(61), table soc(67)
init_microusb_ic: MUIC: CONTROL1:0x1b
init_microusb_ic: MUIC: CONTROL1:0x1b
init_microusb_ic: MUIC: CONTROL2:0x3b
init_microusb_ic: MUIC: CONTROL2:0x3a
PMIC_ID = 0x2
PMIC_IRQSRC = 0x0
PMIC_STATUS1 = 0x10
PMIC_STATUS2 = 0x0
PMIC_PWRON = 0x2
PMIC_IRQ1 = 0xc
PMIC_IRQ2 = 0x0
s5p_check_keypad: keypad value=0x0
s5p_check_reboot_mode: INFORM3 = 0 ... skip
s5p_check_upload: MAGIC CODE=7d98e8c0
microusb_get_attached_device: STATUS1:0x3d, 2:0x0
s5p_check_download: update mode=0
j4fs_read_file_bootloader 355: j4fs panic
s5p_check_tzsw: invalid tzsw type! dummy?
scr_draw_image: draw 'download_error.jpg'...
j4fs_read_file_bootloader 355: j4fs panic
read_param_file: 'download_error.jpg' j4fs read failed!
fimd_div:13, div:1, FB_SOURCE_CLOCK:800000000, FB_PIXEL_CLOCK:57153600
[ERROR:LCD] s6e8ax0_read_id : s6e8ax0_read() failed
 

Top Liked Posts

  • There are no posts matching your filters.
  • 50
    Samsung s3 i9300 & Note2 N7100 & i9500 s4 Dead boot solution & imei null solution s3

    Samsung s3 i9300 & Note2 N7100 & i9500 s4 Dead boot repair solution & imei null solution only for i9300

    Procedure:

    * Download samsung s3 boot card maker Here

    * Extract it on desktop

    * Take a card reader insert memory card into the card reader nd connect it to the pc

    * From the extracted folder run Diskdump2.exe

    * Select generic storage Device. pictures below follw it



    * Now to write the scripts folle the below given picr


    picr.png


    Now done yu are succesfully created Dead boot memorycard

    To continue further

    Requerments:

    * Z3X samsung Box or SPT Box (i used z3x)

    * special UART Cable (300k or 500k uartcable)

    * Download teraterm-4.78 From
    Here

    * Fully charged battery

    Dead boot Reapairing procedure

    * Download nd extract teraterm-4.78 on desktop

    * From extracted folder run ttermpro.exe there select serial port nd change the serial port to z3x serial
    port lik below givin in the picr


    M4u5ZqC.jpg


    *After Select The Serial Port Press Ok Button den Go To Setup Click Serial Port Option
    Select Baud Rate 115200 Then Press Ok Button lik below givn in the picr


    mt7t.jpg

    3mon.jpg



    * Now insert the created boot card to the mobile

    * Connect the Uart cable via z3x box

    * Now Insert the battery nd wait for 5min if the procces didnt start discnnt the mobile close ttermpro agin try it.

    * if it run success yu vil the result below given lik this.

    pit_check_integrity: invalid pit.(0x0)
    pit_check_integrity: invalid pit.(0x0)
    update_guid_partition_table: There is no pit binary.
    fsd_reclaim 1283: MST is not recognized(mst.magic=0x0)
    fsd_reclaim 1284: MST is not recognized
    fsd_reclaim 1599: Error(nErr=0x0)
    fsd_reclaim 1604: j4fs_rw_start is set to default value(128KB)
    j4fs_open 153: Error(nErr=0x40000000)
    j4fs_read_file_bootloader 355: j4fs panic
    load_j4fs_param: 'param.j4fs' does not exist, make new one..
    j4fs_write_file_bootloader 184: j4fs panic
    fail
    j4fs_read_file_bootloader 355: j4fs panic
    load_j4fs_param: debug level file does not exist..*INCORRECT!*
    init_fuel_gauge: battery is not detected, do not init fuelgauge
    init_microusb_ic: MUIC: CONTROL1:0x1b
    init_microusb_ic: MUIC: CONTROL1:0x1b
    init_microusb_ic: MUIC: CONTROL2:0x3b
    init_microusb_ic: MUIC: CONTROL2:0x3a
    PMIC_ID = 0x2
    PMIC_IRQSRC = 0x0
    PMIC_STATUS1 = 0x10
    PMIC_STATUS2 = 0x0
    PMIC_PWRON = 0x2
    PMIC_IRQ1 = 0x27
    PMIC_IRQ2 = 0x0
    s5p_check_keypad: keypad value=0x0
    s5p_check_reboot_mode: INFORM3 = 0 ... skip
    s5p_check_upload: MAGIC CODE=d1b0f038
    microusb_get_attached_device: STATUS1:0x3c, 2:0x0
    s5p_check_download: update mode=0
    j4fs_read_file_bootloader 355: j4fs panic
    s5p_check_tzsw: invalid tzsw type! dummy?
    scr_draw_image: draw 'download_error.jpg'...
    j4fs_read_file_bootloader 355: j4fs panic
    read_param_file: 'download_error.jpg' j4fs read failed!
    fimd_div:13, div:1, FB_SOURCE_CLOCK:800000000, FB_PIXEL_CLOCK:57153600
    a2, 60, 90,

    * if yu get this error at the end [Patch Stop] This is not Rom Code. yu cant fix yur mobile yu have to change yur emmc chip

    TN default
    <OK>
    <OK>
    [DVFS] INT(1) : 0
    DRAM Type : LPDDR2 8G
    [DVFS] MIF(3) : 0
    [EPLL][VPLL][CLK_DIV] OK
    <OK>
    [LOCK SW/HW]ARM:0/0 INT:0/0 G3D:0/0 MIF:0/0 SHIFT:0/0
    [DVFS] ARM(0) : 5
    [DVFS] INT(1) : 0
    [DVFS] G3D(2) : 0
    [DVFS] MIF(3) : 0
    [SD_INIT
    SDMMC_HighSpeedONE]
    SD_READ: 20000 20000 0x40008000 -> 668484 usec
    <OK>
    Inp32(uAddr) : 0xea00007e
    FW Booting
    [Patch Stop] This is not Rom Code.

    * After done this yur mobile must me n download mode or white screen if white screen manually put into download mode.

    * After dead boot repair mine white screen i manually put into download mode pir below

    AMqZJx9.jpg


    * Now update your mobile with factory firmware with PIT file lik below given n the picr.Factory firmware Download Here

    wDaOorh.png


    * After update complete yur mobile may not have imei .imei null or yur mobile will not boot bcoz of dead boot repair. yur efs must be corrupted

    * To Fix this prob first root yur mobile
    Download from here (flash it through odin select as odin)

    * Now Download this EfS repair file nd flash it through odin select as odin yur mobile must boot
    but the imei become lik this 004999010640000

    I9300_Repair_efs.tar.rar

    vnEPYyC.png


    * if yur imei is null yu cant repair using this box so 1st yu have to repair the efs using above givn file. if yur imei bcome lik tis oly (004999010640000) yu can repair using z3x or othr samsung tool

    * Now follw the picr to repair imei problem.


    8WTeetO.png

    4hKIFxn.png

    3tq4AvV.png


    * After IMEI Repair

    tGQBzTH.png


    I hope this post wil helpful for lotz of dem
    :laugh::laugh::laugh::laugh::laugh::laugh: :good::good:











    2
    for anyone looking firmware with 4 files for rescue flash see here


    http://xdaforums.com/showpost.php?p=30087735&postcount=6
    2
    Hello,

    excuse me for asking such a question: which UART cable do I need for repairing my I9300?
    Could you post me please a link? (preferably with shipping to Germany)

    And an other question: one of it's end I have to connect with the USB port of the phone and the other end? With the USB of the PC or with the sd card slot of the phone? I've seen both versions on the internet. Actually I'm a bit confused... Maybe I'm mixing sth. up.

    Thank you very much!

    For this procedure you must need one BOX like Z3X, Octopus, itc...Uart cable is in the stock with Box...only UART cable you can connect in any side of PC..so if you not have any BOX....this procedure isn't for you...try to search in this forum similar procedure w/o use any BOX Samsung...use search button and i'm sure you find other procedure...
    Regards
    Vanito:good:
    1
    i have an n7100 that looks exactly as your s3 in the two pictures. when i turn it on it shows the exact scrambled image,and when entered in boot mode,this is what i get:
    ODIN MODE (red)
    PRODUCT NAME: GT-N7100
    CUSTOM BINARYDOWNLOAD: No
    CURENT BINARY:Samsung Official
    SYSTEM STATUS: Custom
    KNOX WARANTY VOID: 0
    AP SWREV:

    THAT IS THE EXACT MESAGE,NOTHING PLUS OR MINUS
    when i flash whit odin,it sais no pit partition. i need help with the files and procedure

    yours may b a hardware issue . emmc chip problem yu hav to replace it
    1
    any mirror for firmware zip as very slow

    firmware download has 1 file and no pit. where are the 3 files needed?