Hi guys i have stange problem here i can not flash i9300 with odin alwasy get fail when it starting to flash sestem file
can some one tell me what to do?
1-stop kies (if it is installed) before trying to use odin
2-try reinstalling the USB drivers
3-try with the stock SGS3 USB cable if you tried with another cable
4-try on another USB port on your computer
5-try on another computer
If none of this work, it seems that your phone has a R/W corrupt NAND and you will probably never be able to flash it
Start .
One what firmware on the phone .
Two what firmware are you flashing .
Three is the phone SGS3 International I9300 .
Four have you tried re download of firmware .
jje
1-stop kies (if it is installed) before trying to use odin
2-try reinstalling the USB drivers
3-try with the stock SGS3 USB cable if you tried with another cable
4-try on another USB port on your computer
5-try on another computer
If none of this work, it seems that your phone has a R/W corrupt NAND and you will probably never be able to flash it
Actually, I'd recommend one to completely uninstall KIES, since it is utterly worthless. It is possible to uninstall KIES but keep the drivers.
Encryption failed
Unable to complete encryption due to on interruption,perform factory data reset(erasing all your data )before use,After resting try encrypting device again
He set phone encryption in settings and process has been interrupted or there was some errors while encrypting.
This procedure takes a while, even few houers. If phone will be rebooted by user or by power loss (weak battery) encrypion will fail in half way.
You should try to Initialize phone to factory default system by Kies. You need seril number and device name. GT-9300 in this case. Kies will check Samsungs database and try to restore original firmware, also branded. Kies will try to repartition to stock layout, format and flash this firmware.
This option is somwhere in Kies menu, tools if I remember.
If its fail than only option left is try Odin, 3 files firmware, mx.pit and repartition check while flashing.
Wysyłane z mojego GT-I9100 za pomocą Tapatalk 2
Try one more thing, set mx.pit as pit check repartition an UNCHECK autoreboot. Flash only pit. If it finish with success dont reboot your phone and do not disconnect it from Odin. Set this time pda, modem and csc (without repartition) and try to flash.
If it fail than its mean propably damaged nand and only service center will help (maiboard replace).
There is an option to flash only param.fs file as pda but i never tried this metod.
Wysyłane z mojego GT-I9300 za pomocą Tapatalk 2
it fails. (mx.pit)
its very expensive if i change m.board.
so im trying very hard to fix my s3
is there any solution left that im able to try?
help me pls thanks guys
---------- Post added at 02:54 PM ---------- Previous post was at 02:49 PM ----------
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Thanks for ur reply i can not connect wit kies so only option is odin 3 file can u plz give me link for 3 file so i can try to flash and check it out?
thanks again
You don't have i9300 so go away and leave oooollllld threads in peace
Sent from my GT-I9305 using xda app-developers app