for total legit? you need to work for or be a nokia authorised repair center. all other copies are pirated
Hi!
Im new to windows mobile. I've got my Lumia only last week. So iv'e been reading about how to get root access.
Im having hardware rev. - 2.3
But when i connect according to the instructions it says DLOAD
Is there anything i can do?
im currently on FW - 12070
nope..lumia 800 with a DLOAD, we still have to wait :/
even im waiting for a possible downgrade if the bootloader , so we can access Qualcomm :/
we all are waiting ://
its frustrating now actually, cuz der are no updates as well.://
I have a Nokia Lumia 710. Which firmware(s) do i need to use and with which program? Thx!
Chances are yours is DLOAD.What if the method used at the first post does'nt work?
No DLOAD, no usbdisk or whatso ever.
I do see a USB HID, but this is when I release the button combination.
Thanks,
we all are waiting ://
its frustrating now actually, cuz der are no updates as well.://
What if the method used at the first post does'nt work?
No DLOAD, no usbdisk or whatso ever.
I do see a USB HID, but this is when I release the button combination.
Thanks,
[ 655.912077] usb 2-2: new high speed USB device number 9 using ehci_hcd
[ 661.797096] usb 2-2: USB disconnect, device number 9
[ 765.836050] usb 2-2: new high speed USB device number 10 using ehci_hcd
[ 765.968707] usb 2-2: config 1 has an invalid interface number: 20 but max is 1
[ 765.968713] usb 2-2: config 1 has no interface number 1
[ 766.869700] usbcore: registered new interface driver uas
[ 766.905673] Initializing USB Mass Storage driver...
[ 766.905816] scsi2 : usb-storage 2-2:1.20
[ 766.906108] usbcore: registered new interface driver usb-storage
[ 766.906110] USB Mass Storage support registered.
[ 767.906264] scsi 2:0:0:0: Direct-Access Qualcomm MMC Storage 2.31 PQ: 0 ANSI: 2
[ 767.964504] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 767.968542] sd 2:0:0:0: [sdb] 31047680 512-byte logical blocks: (15.8 GB/14.8 GiB)
[ 767.969066] sd 2:0:0:0: [sdb] Write Protect is off
[ 767.969069] sd 2:0:0:0: [sdb] Mode Sense: 0f 0e 00 00
[ 767.970061] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 767.977005] sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 >
[ 767.977264] sdb: p9 size 30632075 extends beyond EOD, enabling native capacity
[ 767.983196] sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 >
[ 767.983463] sdb: p9 size 30632075 extends beyond EOD, truncated
[ 767.988075] sd 2:0:0:0: [sdb] Attached SCSI removable disk
_wmstore
!zLH?k
_wmpart_B
_wmpart_S
_wmpart_S
_wmpart_N
_wmpart_U
_wmpart_D
_wmpart_I
_wmpart_P
_wmpart_U
PSBdX
GFCB
SRPX
*** Compiling the LK Android bootloader ***
** Tested on Ubuntu 11.10 with Lumia 710 **
1) Get the toolchain and install:
wget https://sourcery.mentor.com/public/gnu_toolchain/arm-none-linux-gnueabi/arm-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu.tar.bz2
sudo tar xvf arm-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu.tar.bz2 --directory /opt/
2) Compile the bootloader:
PATH=/opt/arm-2009q1/bin:$PATH TOOLCHAIN_PREFIX=arm-none-linux-gnueabi- PROJECT=msm7630_surf make EMMC_BOOT=1
3) Get your Lumia into diagnostics mode (turn it on using VOL UP + VOL DOWN + POWER)
4) BACKUP EVERY SINGLE FILE FROM THE 150MB PARTITION! (Just to be safe)
5) Replace the image/emmcboot.mbn file with your freshly compiled LK bootloader
cp <repo dir>/build-msm7630_surf/EMMCBOOT.MBN /media/<mount point>/image2/emmcboot.mbn
6) Unmount the bootloader partition from your PC and pull the phone's battery
7) Turn on, wait a few moments, and plug the phone to the PC
8) Test the fastboot connection:
fastboot devices
fastboot getvar version
Yes you are right, I had checked that too,
but I'm a bit scary to brick my phone
what are the benefits of putting an linux kernel, can i still acess wp7 software, and could i flash android on it ?