Hi all I have an old S3 that seems to have kicked the bucket. I am hoping there is some way to save it though. I have been running the last CM 11 milestone for a long while now. I just use the phone with an archlinux chroot to do some linuxy-things. I tried ssh'ing into the phone while I was at work the other day and the ssh session hung. Upon getting home the screen was black and wouldn't turn on. I tried pulling the power and restarting and it just hung at the CM boot logo.
It would boot into TWRP recovery or download mode but never boot. I eventually noticed in TWRP that it said my internal storage was 0MB large and found that the userdata partition was corrupt (e2fsck wouldn't work)
I've tried every combination of flashing a stock .tar and/or .pit file but nothing seems to change.
Here is the output I get when trying to repartition with odin:
and heimdall:
heimdall flash --repartition --verbose --RECOVERY openrecovery-twrp-2.7.1.0-d2att.img --pit ../sgh-i747-16gb.pit --no-reboot
I'm out of ideas, any suggestions?
Thanks
It would boot into TWRP recovery or download mode but never boot. I eventually noticed in TWRP that it said my internal storage was 0MB large and found that the userdata partition was corrupt (e2fsck wouldn't work)
I've tried every combination of flashing a stock .tar and/or .pit file but nothing seems to change.
Here is the output I get when trying to repartition with odin:
Code:
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCDLK3_I747ATTDLK3_I747UCDLK3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
and heimdall:
heimdall flash --repartition --verbose --RECOVERY openrecovery-twrp-2.7.1.0-d2att.img --pit ../sgh-i747-16gb.pit --no-reboot
Code:
Heimdall v1.4.0
Copyright (c) 2010-2013, Benjamin Dobell, Glass Echidna
http://www.glassechidna.com.au/
This software is provided free of charge. Copying and redistribution is
encouraged.
If you appreciate this software and you would like to support future
development please consider donating:
http://www.glassechidna.com.au/donate/
Initialising connection...
Detecting device...
Manufacturer: "Sasmsung"
Product: "MSM8960"
length: 18
device class: 2
S/N: 0
VID:PID: 04E8:685D
bcdDevice: 0100
iMan:iProd:iSer: 1:2:0
nb confs: 1
interface[0].altsetting[0]: num endpoints = 1
Class.SubClass.Protocol: 02.02.01
endpoint[0].address: 82
max packet size: 0010
polling interval: 09
interface[1].altsetting[0]: num endpoints = 2
Class.SubClass.Protocol: 0A.00.00
endpoint[0].address: 81
max packet size: 0200
polling interval: 00
endpoint[1].address: 01
max packet size: 0200
polling interval: 00
Claiming interface...
Attempt failed. Detaching driver...
Claiming interface again...
Setting up interface...
Initialising protocol...
WARNING: Control transfer #1 failed. Result: -9
WARNING: Control transfer #2 failed. Result: -9
WARNING: Control transfer #3 failed. Result: -9
WARNING: Control transfer #4 failed. Result: -9
WARNING: Control transfer #5 failed. Result: -9
WARNING: Control transfer #6 failed. Result: -9
Protocol initialisation successful.
Beginning session...
Some devices may take up to 2 minutes to respond.
Please be patient!
Session begun.
Uploading PIT
ERROR: Failed to unpack received packet.
ERROR: Failed to confirm end of PIT file transfer!
ERROR: PIT upload failed!
Ending session...
Releasing device interface...
Re-attaching kernel driver...
I'm out of ideas, any suggestions?
Thanks