S-off is Official!!! With Instructions...

Search This thread

antp121

Senior Member
Jan 15, 2011
6,056
2,061
New Jersey
Yeah so i got s-off, then ruu'ed to GB firmwares
now im trying to flash amon ra and im getting this

C:\AndroidRez>fastboot flash recovery recovery-ra-vigor-3.15-gnm.img
sending 'recovery' (7078 KB)...
OKAY [ 1.467s]
writing 'recovery'...
FAILED (remote: not allowed)
finished. total time: 1.783s

Any help?

Unlock your bootloader or flash their eng hboot.

Sent from my ADR6425LVW using XDA
 

LakerStar25

Senior Member
Jan 25, 2011
511
88
LA
People having the no beer for tonight thing reformat the SD card again and start the program over that helped me. Try that see if it helps.

Sent from my S-OFF ICS Rezound
 

antp121

Senior Member
Jan 15, 2011
6,056
2,061
New Jersey
Could this issue that some are having with the no beer be related to what firmware and version of exploit they using? My success was on ics firmware and exploit

Sent from my ADR6425LVW using Tapatalk 2

Same. I s-offed on ics, downgraded to gb, then upgraded to ics then installed their hboot, then installed recovery then flashed a Rom. Everything works peachy and I have s-off :)

Sent from my ADR6425LVW using XDA
 

antp121

Senior Member
Jan 15, 2011
6,056
2,061
New Jersey
Alright guys I'm calling it a night. If you need help, pm me and ill respond in the morning. I hope you guys can sort through your problems and that you can s-off successfully. Good night and good luck.
antp121

Sent from my ADR6425LVW using XDA
 

m3Jorge

Senior Member
Nov 29, 2007
216
19
Tampa, FL
Phone not detecting usb connection anymore!!!

Finally got it to work!!!!

Man the "wire trick" is really "tricky!"

Question though, If I flashed the "modified" HBOOT can I go back to the ICS stock HBOOT without loosing S-Off?
 
Last edited:

loolugee

Member
Mar 25, 2012
27
0
I just want to know, with s-off how can you switch htc rezound to another company like tmobile or att in the U.S.??
 

Marine6680

Senior Member
Jul 12, 2009
1,479
201
Kingsport TN
Yeah so i got s-off, then ruu'ed to GB firmwares
now im trying to flash amon ra and im getting this

C:\AndroidRez>fastboot flash recovery recovery-ra-vigor-3.15-gnm.img
sending 'recovery' (7078 KB)...
OKAY [ 1.467s]
writing 'recovery'...
FAILED (remote: not allowed)
finished. total time: 1.783s

Any help?

You need their supplied hboot.

Basically that error says that you are not allowed to change the recovery using ADB commands from a PC. Installing their supplied Hboot will help. (when it asked you to install it during the S=Off process) You can flash it manually though.

Haha same. I think I got like ten thanks in like 4 hours lol. No offense to anyone just its been a looooooong night lol

Sent from my ADR6425LVW using XDA

I started all this and then helping 8 hours ago... only a short break for food and a tv show... :eek:

Alright guys I'm calling it a night. If you need help, pm me and ill respond in the morning. I hope you guys can sort through your problems and that you can s-off successfully. Good night and good luck.
antp121

Sent from my ADR6425LVW using XDA

/Wakes up to a hundred PMs

:cool:
 

baker954

Member
Nov 7, 2009
24
4
Indianapolis
Confirmed!!!!

Confirmed S-OFF here as well!!

I'm at work, so I used a large paperclip, wrapped it in clear tape (like the ones on top of a desk), and got 'er done!!!

Amazing work!!!

Absolutely NO ISSUES during process.

THANK YOU VERY MUCH!



Running CleanROM Developer Edition with the patch, ran the process, installed the final hboot file, completed, it rebooted, then rebooted again and I'm good to go!
 
Last edited:

pwned3

Senior Member
Jul 23, 2011
1,261
275
Cullman
Success here too after about 3 hours of trying. New splash here I come

Sent from my ADR6425LVW using Tapatalk 2
 

Marine6680

Senior Member
Jul 12, 2009
1,479
201
Kingsport TN
Here is a question I was asked.

red3razor said:
hello, having troubles, could you be of help please?

at first i was having trouble controlbear even recognizing my phone, now got it to run all the way through after wire trick. success twice. but get all the way through to error code 667377 or so (still sober). now i am back at cleanRom with no recognizable sdcard. do i keep re-running controlbear until wire trick is successful? is there anything else i should do? thanks so much in advance

You will need to reformat your SDcard between each attempt, as it wipes the card of all formating. It is basically empty memory with no usable file system.

Part of the process formats the card and then installs some files, then the "wire trick" (I am speculating) causes the phone to reboot and read the card. The second tap of the wire trick allows the files to run but interrupts at just the right moment to prevent s=on checks from kicking in and stopping the exploit from working.

Therefore timing between the two taps is critical... use a watch or other device that counts seconds to help get your mental counting at the right pace. The wire trick taps should be quick (I.E do not hold the wire to the contacts just touch briefly) and about 1.5 seconds apart.

At some point this corrupts the card's file system or wipes the partition table of the memory card, forcing a reformat. Without a format, the app can not install the needed files to the card.

"Still sober" means you mis-timed between the two taps of the "wire trick"
 
  • Like
Reactions: red3razor

NAU420

Senior Member
Apr 8, 2012
242
29
Ok now I have a black HTC screen and this for the last 15 mins:

Starting up......
* daemon not running. starting it now *
* daemon started successfully *
Making room for beer......
Loading sixpacks on sdcard......
Loaded......
Board vigor detected

WTH am I doing wrong now??
 

red3razor

Senior Member
Jan 27, 2012
429
375
between taps with wire, can i continue to hold onto "pin 1" before tapping GND a second time? or should i release wire from both contacts before pushing onto both contacts the second time?
 

Top Liked Posts

  • There are no posts matching your filters.
  • 110
    Fixes for Internal Memory and External SD card are at bottom of post!

    May be easier to make a completely new thread instead of people searching through the "s-off discussion" thread.

    I'm going to make a huge SD Card post right at the top because it seems like people still are overlooking it in the "s-off discussion" thread... Not trying to be a ****, just making sure people don't lose crucial information on their SD cards...

    Version 0.4 should not wipe internal memory anymore and should back up your external SD card: but I would still back up both just to be sure!!!!

    Here's the link for Instructions:

    http://unlimited.io/instructions/

    Read the Instructions carefully and thoroughly at least once before attempting. This will temporarily brick your phone. Don't be lazy. Don't forget this will format your SD card so save all your contents or use a spare!!! I used my old 2GB droid incredible sd card for mine...

    Prerequisites said:
    Prerequisites

    In order to use JuopunutBear you must meet the following pre-requisites:

    Be unlocked using the HTCdev bootloader unlock
    Be rooted (have superuser and/or an unsecured boot image installed)
    Have a spare microSD card, or to have backed up all contents of your SDcard
    Have fastboot and adb drivers installed and working (windows)
    Have usb debugging enabled
    Have a legth of insulated wire of sufficient length to join the contact points for your device. See images and videos for device specific information.

    Some notes:

    Make sure back cover is off before running program.
    Plug in phone before running program.
    Boot phone into ROM before running program, it will automatically boot into fastboot by itself.
    Don't do wire trick until after you run the program and tells you to do so!!!
    Make sure you have "USB debugging" enabled!
    If in Windows, right click program and make sure you click "Run as Administrator"

    This post sums up everything nicely...

    http://xdaforums.com/showpost.php?p=25154023&postcount=1289

    Instructions said:
    Instructions

    (Optional) Perform a full backup and replace your sdcard with one that you are willing to wipe.
    Ensure that your battery is fully charged.
    Choose the correct download for your device and operating system
    Extract the zip file to a new directory
    Verify the MD5 checksum for your download
    Read and/or watch the video for the device specific information for your device
    Run controlbear as admin(windows) or root or using sudo on linux
    Follow the on-screen instructions from ControlBear
    Do not press any of the buttons on the phone during the process.
    After doing the “wire-trick” yor phone will reboot. The sequence of the reboot may vary somewhat from that you see in the videos as these were taken during various stages of development.
    If you see the following message from ControlBear after doing the wire trick:
    ErrorMsg: Still sober.
    This means that you have been unsuccessful in implementing the wire-trick. Run ControlBear again.
    The usual casue for this is that you failed to perform 2 clean contacts or mistimed the wire trick.

    Your phone will reboot several times during the process, this is normal. ControlBear will tell you when it has finished whether sucessfully or not.

    Here's link for wire trick:

    http://unlimited.io/htc-rezound/

    Wire Tips:

    22ga wire fits almost perfect in the lower hole.

    Use a piece about 8 inches long and stripped the end for the lower contact about 3/8 of an inch and the other end just a small amount. Did this to two phones and it worked the first time both times.

    It was reported that the large coated paper clips work well too.

    Others are using odd objects or other weird improvised wires and having a lot of trouble. It seems to be one of the big sticking points.

    I honestly used a paperclip and it worked just fine. Not even insulated... even though they don't recommend it: you could use it as a last resort.... or wrap it with an insulated material. I didn't know the paper clip had to be because I was one of the beta testers.

    Don't make this mistake either.

    Wire Trick said:
    Wire Trick

    The “wire trick” is an essential part of the JuopunutBear S-OFF procedure.

    When instructed to do so by the program you must perform the “wire trick” which is done as follows.

    Obtain an insulated wire of appropriate length and gauge
    Insert one end of the wire into the hole where pin 1 is indicated in the picture below, ensuring that a firm contact it made with the metal contact at the bottom of the hole
    Briefly touch to other end of the wire to the contact marked GND in the picture below.
    Wait approximately 1.75 seconds and then again touch the wire to the marked GND.
    Allow the program to continue.

    Note: it may take several attempts of running the program in order to obtain the correct timing for the wire trick.

    The contact points for the “wire trick” are shown in the picture below.

    If you're not getting it after wire trick, keep trying! Timing is crucial!!!

    Don't forget this will format your SD card so save all your contents or use a spare!!!

    Picture of Points:

    rezound.jpg


    Video of Wire Trick:


    New ICS hboot should be included in the download now.
    http://xdaforums.com/showpost.php?p=25147001&postcount=1141

    Very nice thread walkthrough thread for fixing external SD right here!
    Fix for external SD is as follows:

    1. Install busybox
    2. adb shell busybox fdisk /dev/block/mmcblk1
    3. type o
    4. type w
    5. adb shell busybox fdisk /dev/block/mmcblk1
    6. type n
    7. select primary, then 1
    8. chose default sizes
    9. type w
    10. adb shell busybox mkfs.vfat /dev/block/mmcblk1p1

    For those of you having problems with internal storage, my apologies. We accidentally included the GB hboot.

    Download this:

    http://dl.dropbox.com/u/14779955/jb_hboot.zip MD5: b05336c08f709bf0a909205bcb95b951

    Put the phone in fastboot mode, then run the follwoing commands:
    Code:
    fastboot oem rebootRUU
    fastboot flash zip jb_hboot.zip
    fastboot reboot

    Ignore the green bar.

    Pretty much copied everything off the site, but it may be easier to use instead of switch tabs/windows... Good Luck...

    Disclaimer: I am not responsible for bricked devices or anything happening to your handset!!!! Just relaying the message


    If you're still having issues... The search button is your friend. :) There's a high chance your problem has already been solved. Either search this thread or the discussion of s-off thread. Don't know how to search? WELL NOW YOU CAN IN THIS SIMPLE TUTORIAL!!!!!

    Some more threads you might want to check out!!!!

    AR recovery and s-off ( fix )

    [FAQ] S-Off

    just got s-off? please read this.


    Oh yeah... ENJOY S-OFF!!!!!

    These guys put in a hell of a lot of effort into doing this process... Any donation would be greatly appreciated!

    Donate to JuopunutBear Team!!!
    9
    There really is a need for a comprehensive set of instructions (but I'm not quite free enough to do it myself). NOTE - THESE INSTRUCTIONS ARE FOR THOSE ALREADY ON THE ICS LEAK WITH HBOOT 2.21 AND AN HBOOT THAT READS "TAMPERED - UNLOCKED." If you are on hboot 2.11 or any other hboot, I can't say for sure whether the following applies to you. If you are on GB, I can't say whether the following applies to you. It was my experience only, and I was successful, and I'm just sharing because after 100+ pages of pretty much the same 10-12 issues, I figure I can at least try to make things easier.

    1. Don't try to get S-OFF if you are unrooted or have a locked bootloader. Read the darn instructions through from beginning to end, and review the OP's in this thread, and search for any issues about which you are curious. In fact, go read them again from beginning to end just to make sure you get it right, then come back here.

    2. BEFORE YOU START, make sure you have available both an *.img file and PH98IMG.ZIP of (1) your recovery; and (2) your boot image.

    3. PULL YOUR SDCARD AND USE A DIFFERENT CARD FIRST. I'm sorry, anyone who has whined about wiping their only card --- you shouldn't play with grown-ups; you didn't read the instructions. If you only have one card BACK IT THE HELL UP, cause it's gonna get wiped.

    4. Back up your "internal" SD card. If you're running 0.2 version of ControlBear, it shouldn't get wiped, but you never know what else is going to happen that could wipe it. (Mine was untouched).

    5. Gee, you could also do a Nandroid and save it to your PC.

    6. All the Juopunut files go in the same file directory on your PC as fastboot.exe and adb.exe.

    7. Kill HTC Sync if you're really still running it.

    8. Open a command line box; navigate to the directory where you have adb and fastboot (and controlbear.exe and the two supporting files, it's own boot image and its hboot.)

    9. Make sure you are admin on your PC.

    10. Make sure your Rezound is fully charged, back cover off, connect to a cable (but not yet connected to PC) and you have your insulated paperclip or whatever tool you're going to use. LOOK AT THE PICTURE to be sure you know where you need to touch the wires. You will have time. Put the phone face down on a table or desk.

    11. Consider having a metronome around or something to beat out 34 bpm so you know the frequency. Here's a 35 second track (in *.aac format) you can loop on your computer while you're doing it so you have a feel for the interval. I used this when I got S-OFF.

    12. Run Controlbear. When it tells you, connect the device.

    13. If it doesn't seem to see the device after a few minutes, kill it and start it over. Leave your phone alone.

    14. Eventually, your phone's going to start rebooting and you'll get a prompt to do the wire trick. You will get that prompt for a few minutes and you'll have repeated chances to do the trick. After that, ControlBear talks about beer and other nonsense, and either tells you that you are still sober (exploit failed) or otherwise just sort of sits there. After a few minutes, if you seem to be nowhere, kill ControlBear (close the DOS box) and restart it. Leave your phone alone. Ignore any prompts from the PC about devices connecting.

    15. Repeat #14 until: (1) ControlBear reports success; or (2) Nothing seems to be happening (and your phone has a green arrow pointing down and Juopunut on the front).

    16. If things are stuck that way for >5 minutes (AND you're seeing no changes in your DOS box, no information scrolling, words such as "mmm, tasty", try to reboot into bootloader on your Phone. You might already have S-OFF (that was what happened to me, even though ControlBear never reported success). Be patient, wait a few minutes. Relax. You aren't going to brick your phone. As long as you can reboot to bootloader, ANY bootloader, you aren't bricked.

    17. If you aren't S-OFF, go back to #14, if you are, go on.

    18. Power off the phone. PULL THE SDCARD. If it isn't your "default" SDCARD, you don't need it anymore, you can put your regular card in. If it is your ONLY card, format the card Fat32 on the PC using a card reader.

    19. Using a cardreader, put Juopunut's BOOTLOADER on my SD card as PH98IMG.ZIP (i.e., rename it, it's the file with hboot in the name), reboot to bootloader and accept the update. From the "new" Juopunut's hboot, power down the phone. Remove the card again.

    20. Using a cardreader, remove the PH98IMG.ZIP of the hboot from the SD card. Put the card back in the phone.

    21. Reboot to bootloader, selected fastboot, connect to your PC, using fastboot USB reflash Amon Ra. (You could also do this as a PH98IMG.ZIP if you choose by putting it on the card).

    22. Power off. Remove card AGAIN, put boot image on card as PH98IMG.ZIP (taking off the old PH98IMG.ZIP if that's how you reflashed Amon Ra).

    23. Reboot to bootloader and flash your boot image, either via fastboot or as an PH98IMG.zip cf. step 21.

    24. Power OFF, boot normally, which should finally get you past the Juopunut splash screen. You might even bootloop once or twice (I did), but you should get a normal boot at that point.

    25. Note, if you boot to bootloader, flash recovery, then go from bootloader directly to recovery you will probably have have issues. Instead, after step 24, Power off or restart into recovery AFTER you've successfully booted your ROM. Amon Ra should behave perfectly normal at that point.

    The preceding was my experience at any rate.

    Yeah, Unrevoked was a lot easier and quick for those of us coming from Incredible, but it really isn't impossible to do this if you remain patient, pay attention, and stay calm.
    6
    for anyone whos done it what kind of wire have u used?

    I used a paperclip that was insulated. So just wrap one up with electrical tape and that will be fine.
    6
    Its actually quite fascinating to me to see so many varied results and peoples' reactions to the process. I'm also starting to realize that most of the people in here will put pretty much anything on their phone (or do pretty much anything to it..) even when they clearly have no idea what they are even doing it for.

    I mean seriously, half the people in here trying to get S-OFF and driving themselves insane probably shouldn't even be worrying about it anyway. But they will do it anyway. And then the next thing they'll do, for no apparent reason and without knowing anything at all about them, is start flashing radios. Then the next thing they will say is they can't make calls anymore and can't figure out why...
    6
    What should I do???
    Give me a hand! Thank you

    LOL really? You mean you did all this stuff to your phone that could potentially destroy it, and you didn't even read all the instructions first??! OK, now go ahead and facepalm for a second....


    ...OK lecture over.
    1) Go to the development section, find the Amon Ra recovery thread, and find somewhere in there the latest version 3.15 and download it (check around page 48)

    2) extract the .img file to a folder somewhere on your computer where you have the fastboot and adb applications located

    3) turn off the phone. Boot it into fastboot by holding volume-down and power, then selecting fastboot at the menu

    4) plug phone into computer - wait for phone to say "fastboot - usb"

    5) type the command "fastboot flash recovery recovery-ra-3.15-gnm.img" to flash the file (make sure the filename matches, that was from memory)

    6) then type "fastboot reboot recovery"

    7) Once Amone Ra boots, go to the developers menu and then select install su from there.

    Yes, I just typed all that out for you, even though its all readily available with a simple SEARCH. You're welcome.