Before you start, backup anything on your phone you might want to keep after the new Rom has been flashed as all contacts, emails, texts, notes, Internet BookMarks/ ect. WILL be lost!!
PimBackup is good and free (copy any mms attachments to your storage card or computer seperately)
[FONT="]***THIS TUTORIAL IS FOR THE GSM RAPHAEL'S ONLY!!! DO NOT USE WITH CDMA VERSIONS***[/FONT]
[FONT="]If your phone has a SIM Card Slot then its a GSM Model. Carry on reading.[/FONT]
[FONT="]If it has no SIM Card then its CDMA and you should not use this procedure.[/FONT]
[FONT="]**USE THE WIKI FOR EVERYTHING YOU WANT TO KNOW ABOUT YOUR RAPHAEL**[/FONT]
[FONT="]*ONCE YOU HAVE FLASHED A HARDSPL ITS PERMANENT. YOU DONT NEED TO DO IT AGAIN WHEN FLASHING NEW ROMS OR RADIOS*[/FONT]
[FONT="]*DO NOT start another process while the flashing process is taking place*[/FONT]
[FONT="]*DO NOT click off of the status bar... Let it stay in the foreground* [/FONT]
[FONT="]*DO NOT let the Screensaver activate*[/FONT]
[FONT="](any of these can lead to a bad flash and possibly brick your phone)[/FONT]
*FLASH HARDSPL BEFORE FLASHING ANY CUSTOM ROMS*
[FONT="]1. YOUR DEVICE MUST HAVE AT LEAST 50% BATTERY POWER FIRST BEFORE ATTEMPTING EACH STAGE[/FONT]
[FONT="]2. FLASH HARDSPL[/FONT]
Before flashing make sure you have installed Microsoft .NET Framework 3.5 on your PC
[FONT="]Flashing via ActiveSync with USB Lead (thanks to [/FONT][FONT="]OliNex)[/FONT]
1. Download Hard-SPL package and unzip it to your Hard Drive. Make sure it's launched from a local drive (not through network drive, etc.)
2. REMOVE SIM and SD CARDS!!
3. Turn phone back on and let it boot back into your operating system
4. Connect your phone to PC with a USB cable and wait until it syncs with your PC
5. Run RaphaelHardSPL-Unsigned_190_1_3.exe
6. Follow steps in the RUU (Rom Update Utility), check device for prompts after PC shows loading bar
7. It should go to a black screen now
8. SPL flashes, device automatically reboots, job done
9. To confirm you installed it correctly, go into bootloader mode (tricolour screen!) and verify the screen shows 1.90.OliNex
[FONT="]**To enter Bootloader and check HardSPL version; with the device turned OFF, press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears**[/FONT]
[FONT="]NOTE 1: You will not see the SPL version during normal boot, that is the OS version, not SPL![/FONT]
[FONT="]NOTE 2: Anyone having problems with the device entering SSPL automatically, please copy SSPLManual.exe from the download to the device and run it. Once the screen is black, run RUU manually from the PC.[/FONT]
[FONT="]NOTE 3: This is an unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. Also, this has overwrite protection, if someone needs to revert to stock SPL for warranty reasons, go *HERE*[/FONT]
[FONT="]NOTE 4: DO NOT use this RUU for anything other than SPL flashing (i.e. hardspl or stock spl restore)!!! If you want to flash some other rom, then use customruu from *HERE* [/FONT]
[FONT="]3. SIM AND CID UNLOCK [/FONT][FONT="](OPTIONAL)[/FONT][FONT="].[/FONT]
[FONT="]Note: You do not need to SIM or CID Unlock your phone to flash a new Rom.[/FONT]
[FONT="]If, however you want to flash Diamond/ Blacksone Radios OR use your phone on a different Network then you MUST Unlock your phone.[/FONT]
[FONT="]To Unlock your phone go *HERE*[/FONT]
[FONT="]4. DOWNLOAD AND FLASH YOUR PREFERED ROM.[/FONT]
[FONT="]Flashing Via ActiveSync[/FONT]
[FONT="]1. Download your prefered Rom from the Raphael Rom Develpoment Page and unzip/unrar it to your computer[/FONT]
[FONT="]2. REMOVE SIM and microSD CARDS!![/FONT]
[FONT="]3. Turn phone back on and wait until it syncs with your PC[/FONT]
[FONT="]4. Run the Raphael_RUU.exe (or [/FONT]RaphaelWrapper.exe if thats included instead) [FONT="]from the Roms Folder[/FONT]
[FONT="]5. Once phone finishes flashing and gets to the screen where it configures the stylus, HARD RESET[/FONT]
[FONT="](hold the VOLUME DOWN and ENTER (center) Buttons, press the RESET button with the stylus tip, then release the RESET button but continue to hold the VOLUME DOWN and ENTER buttons until the reset screen appears)[/FONT]
[FONT="]6. Follow onscreen instructions to set up your New Rom[/FONT]
[FONT="]7. Once phone has gone through the customisation procedure then replace Sim and microSD Cards[/FONT]
[FONT="]8. Turn phone back on and set up as required[/FONT]
[FONT="]Flashing Via MicroSD Card[/FONT]
[FONT="]1. Make sure your microSD is Formatted to fat32 using a PC (you dont have to delete all files but it is safer if you do)[/FONT]
[FONT="]2. Download your prefered Rom from the Raphael Rom Develpoment Page and unzip/unrar it to your computer[/FONT]
[FONT="]3. Goto the Roms Folder and rename the .nbh file to RAPHIMG.nbh[/FONT]
[FONT="]4. Copy the RAPHIMG.nbh file to the root of your microSD Card[/FONT]
[FONT="]5. Remove Sim Card and Restart phone
6. Plug the microSD Card into the phone[/FONT]
[FONT="]7. Press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears[/FONT]
[FONT="]8. Follow the onscreen instructions to start flashing[/FONT]
9. Once phone finishes flashing and says Update Complete, reset with the stylus
[FONT="]10. When it gets to the screen where it configures the stylus, HARD RESET[/FONT]
[FONT="](hold the VOLUME DOWN and ENTER (center) Buttons, press the RESET button with the stylus tip, then release the RESET button but continue to hold the VOLUME DOWN and ENTER buttons until the reset screen appears)[/FONT]
[FONT="]11. Follow onscreen instructions to set up your New Rom[/FONT]
[FONT="]5. FLASH PREFERED RADIO IF DESIRED (OPTIONAL).[/FONT]
[FONT="]For more information about different compatible Radios that you can use go *HERE*[/FONT]
[FONT="]**If you want to Flash a Non Raphael Radio then your phone MUST be Security Unlocked** [/FONT]
[FONT="]Flashing Via ActiveSync[/FONT]
[FONT="]Sync your phone with the PC, Run the Raphael_RUU.exe from the Radio's Folder and follow the instructions.[/FONT]
[FONT="]Flashing via MicroSD Card[/FONT]
[FONT="]1. Make sure your microSD is Formatted to fat32 using a PC (you dont have to delete all files but it is safer if you do)[/FONT]
[FONT="]2. Download your prefered Radio from the Raphael Rom Develpoment Page and unzip/unrar it to your computer[/FONT]
[FONT="]3. Goto the Radios Folder and rename the .nbh file to RAPHIMG.nbh[/FONT]
[FONT="]4. Copy the RAPHIMG.nbh file to the root of your microSD Card[/FONT]
[FONT="]5. Plug the microSD Card into the phone[/FONT]
[FONT="]6. Press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears[/FONT]
[FONT="]7. Follow the onscreen instructions to start flashing[/FONT]
[FONT="]8. After the flash finishes press the reset button with the stylus to reset the device[/FONT]
[FONT="]6. JOB DONE[/FONT][FONT="]. Well Done YOU DID IT!![/FONT]
[FONT="]I have attached all the files needed so you dont need to hunt around for anything. Good Luck.[/FONT]
[FONT="]*DISCLAIMER*[/FONT]
[FONT="]I take no responsibility for any fault or damage caused by any procedures within this guide. No warranties of any kind are given.[/FONT]
PimBackup is good and free (copy any mms attachments to your storage card or computer seperately)
[FONT="]***THIS TUTORIAL IS FOR THE GSM RAPHAEL'S ONLY!!! DO NOT USE WITH CDMA VERSIONS***[/FONT]
[FONT="]If your phone has a SIM Card Slot then its a GSM Model. Carry on reading.[/FONT]
[FONT="]If it has no SIM Card then its CDMA and you should not use this procedure.[/FONT]
[FONT="]**USE THE WIKI FOR EVERYTHING YOU WANT TO KNOW ABOUT YOUR RAPHAEL**[/FONT]
[FONT="]*ONCE YOU HAVE FLASHED A HARDSPL ITS PERMANENT. YOU DONT NEED TO DO IT AGAIN WHEN FLASHING NEW ROMS OR RADIOS*[/FONT]
[FONT="]*DO NOT start another process while the flashing process is taking place*[/FONT]
[FONT="]*DO NOT click off of the status bar... Let it stay in the foreground* [/FONT]
[FONT="]*DO NOT let the Screensaver activate*[/FONT]
[FONT="](any of these can lead to a bad flash and possibly brick your phone)[/FONT]
*FLASH HARDSPL BEFORE FLASHING ANY CUSTOM ROMS*
[FONT="]1. YOUR DEVICE MUST HAVE AT LEAST 50% BATTERY POWER FIRST BEFORE ATTEMPTING EACH STAGE[/FONT]
[FONT="]2. FLASH HARDSPL[/FONT]
Before flashing make sure you have installed Microsoft .NET Framework 3.5 on your PC
[FONT="]Flashing via ActiveSync with USB Lead (thanks to [/FONT][FONT="]OliNex)[/FONT]
1. Download Hard-SPL package and unzip it to your Hard Drive. Make sure it's launched from a local drive (not through network drive, etc.)
2. REMOVE SIM and SD CARDS!!
3. Turn phone back on and let it boot back into your operating system
4. Connect your phone to PC with a USB cable and wait until it syncs with your PC
5. Run RaphaelHardSPL-Unsigned_190_1_3.exe
6. Follow steps in the RUU (Rom Update Utility), check device for prompts after PC shows loading bar
7. It should go to a black screen now
8. SPL flashes, device automatically reboots, job done
9. To confirm you installed it correctly, go into bootloader mode (tricolour screen!) and verify the screen shows 1.90.OliNex
[FONT="]**To enter Bootloader and check HardSPL version; with the device turned OFF, press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears**[/FONT]
[FONT="]NOTE 1: You will not see the SPL version during normal boot, that is the OS version, not SPL![/FONT]
[FONT="]NOTE 2: Anyone having problems with the device entering SSPL automatically, please copy SSPLManual.exe from the download to the device and run it. Once the screen is black, run RUU manually from the PC.[/FONT]
[FONT="]NOTE 3: This is an unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. Also, this has overwrite protection, if someone needs to revert to stock SPL for warranty reasons, go *HERE*[/FONT]
[FONT="]NOTE 4: DO NOT use this RUU for anything other than SPL flashing (i.e. hardspl or stock spl restore)!!! If you want to flash some other rom, then use customruu from *HERE* [/FONT]
[FONT="]3. SIM AND CID UNLOCK [/FONT][FONT="](OPTIONAL)[/FONT][FONT="].[/FONT]
[FONT="]Note: You do not need to SIM or CID Unlock your phone to flash a new Rom.[/FONT]
[FONT="]If, however you want to flash Diamond/ Blacksone Radios OR use your phone on a different Network then you MUST Unlock your phone.[/FONT]
[FONT="]To Unlock your phone go *HERE*[/FONT]
[FONT="]4. DOWNLOAD AND FLASH YOUR PREFERED ROM.[/FONT]
[FONT="]Flashing Via ActiveSync[/FONT]
[FONT="]1. Download your prefered Rom from the Raphael Rom Develpoment Page and unzip/unrar it to your computer[/FONT]
[FONT="]2. REMOVE SIM and microSD CARDS!![/FONT]
[FONT="]3. Turn phone back on and wait until it syncs with your PC[/FONT]
[FONT="]4. Run the Raphael_RUU.exe (or [/FONT]RaphaelWrapper.exe if thats included instead) [FONT="]from the Roms Folder[/FONT]
[FONT="]5. Once phone finishes flashing and gets to the screen where it configures the stylus, HARD RESET[/FONT]
[FONT="](hold the VOLUME DOWN and ENTER (center) Buttons, press the RESET button with the stylus tip, then release the RESET button but continue to hold the VOLUME DOWN and ENTER buttons until the reset screen appears)[/FONT]
[FONT="]6. Follow onscreen instructions to set up your New Rom[/FONT]
[FONT="]7. Once phone has gone through the customisation procedure then replace Sim and microSD Cards[/FONT]
[FONT="]8. Turn phone back on and set up as required[/FONT]
[FONT="]Flashing Via MicroSD Card[/FONT]
[FONT="]1. Make sure your microSD is Formatted to fat32 using a PC (you dont have to delete all files but it is safer if you do)[/FONT]
[FONT="]2. Download your prefered Rom from the Raphael Rom Develpoment Page and unzip/unrar it to your computer[/FONT]
[FONT="]3. Goto the Roms Folder and rename the .nbh file to RAPHIMG.nbh[/FONT]
[FONT="]4. Copy the RAPHIMG.nbh file to the root of your microSD Card[/FONT]
[FONT="]5. Remove Sim Card and Restart phone
6. Plug the microSD Card into the phone[/FONT]
[FONT="]7. Press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears[/FONT]
[FONT="]8. Follow the onscreen instructions to start flashing[/FONT]
9. Once phone finishes flashing and says Update Complete, reset with the stylus
[FONT="]10. When it gets to the screen where it configures the stylus, HARD RESET[/FONT]
[FONT="](hold the VOLUME DOWN and ENTER (center) Buttons, press the RESET button with the stylus tip, then release the RESET button but continue to hold the VOLUME DOWN and ENTER buttons until the reset screen appears)[/FONT]
[FONT="]11. Follow onscreen instructions to set up your New Rom[/FONT]
[FONT="]5. FLASH PREFERED RADIO IF DESIRED (OPTIONAL).[/FONT]
[FONT="]For more information about different compatible Radios that you can use go *HERE*[/FONT]
[FONT="]**If you want to Flash a Non Raphael Radio then your phone MUST be Security Unlocked** [/FONT]
[FONT="]Flashing Via ActiveSync[/FONT]
[FONT="]Sync your phone with the PC, Run the Raphael_RUU.exe from the Radio's Folder and follow the instructions.[/FONT]
[FONT="]Flashing via MicroSD Card[/FONT]
[FONT="]1. Make sure your microSD is Formatted to fat32 using a PC (you dont have to delete all files but it is safer if you do)[/FONT]
[FONT="]2. Download your prefered Radio from the Raphael Rom Develpoment Page and unzip/unrar it to your computer[/FONT]
[FONT="]3. Goto the Radios Folder and rename the .nbh file to RAPHIMG.nbh[/FONT]
[FONT="]4. Copy the RAPHIMG.nbh file to the root of your microSD Card[/FONT]
[FONT="]5. Plug the microSD Card into the phone[/FONT]
[FONT="]6. Press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears[/FONT]
[FONT="]7. Follow the onscreen instructions to start flashing[/FONT]
[FONT="]8. After the flash finishes press the reset button with the stylus to reset the device[/FONT]
[FONT="]6. JOB DONE[/FONT][FONT="]. Well Done YOU DID IT!![/FONT]
[FONT="]I have attached all the files needed so you dont need to hunt around for anything. Good Luck.[/FONT]
[FONT="]*DISCLAIMER*[/FONT]
[FONT="]I take no responsibility for any fault or damage caused by any procedures within this guide. No warranties of any kind are given.[/FONT]
Last edited: