Prerequisites
- Charge your device to a minimum of 90% as since the procedure is bit lengthy, the phone will consume more battery than the normal usage. Lesser battery will lead to the turning Off of the device in the middle of the firmware update process.
- Back up all your data which is there in the phone memory, as in an unlikely event if the data gets lost then you can easily restore the backup.
- Up next is you need to ensure that the USB Debugging is enabled in your phone. The USB Debugging can be enabled from the path of Settings > Applications > Development > USB debugging. Apart from this you also need to ensure that your computer has ADMIN privileges and USB Read / Write Access. It’s not recommended to use computers which have limited access.
Instructions For Custom ROM users
Just in case if you are on any of the custom ROMs then you need turn Off your phone so that you can then enter into the recovery mode. The recovery mode can be entered by pressing Volume UP Key + Middle button, and holding both simultaneously press the Power Button. If the device boots normally then you need to again try to enter the same.
In the recovery mode, select the options like Wipe data/factory reset, Wipe Cache partition and then select reboot system now to reboot the phone. You can select the options using the Volume keys and can select the appropriate option by pressing the Power button. This basically clears off all the cache data which is there in the phone so that the room can be made to accommodate this all new custom ROM firmwares
Procedure For Updating
STEP 1: Official Firmware Installation
First up you need to update your phone with the 2.3.x version of firmware (And not on Froyo 2.2.x). You need to follow the instructions which are mentioned below in the form of Links. Please note that it’s a base firmware and you need to install it
STEP 2:Install ClockWorkMod 5 Recovery Image
First up you need to download the beni_cwm-5_ext4_v2.tar & odin+beni.ops.zip.Extract the files and Find Odin 4.38.exe And BENI_v1.0.ops in your Extracted Folder.
Now, Switch off Your Fit And Enter into Download Mode By Pressing Power+Menu Button+Volume Down Button Until Downloading Mode Appears.Open S5670_Odin_Multi_Downloader_v4.38.exe.Place BENI_v1.0.ops on OPS tab.Check the One Package Option.Place beni_cwm-5_ext4_v2.tar on One Package tab.Connect the device to PC which you have put in Downloading Mode.Press Start and wait for flashing process is finished.
After this you will have to proceed to the next step which is mentioned Further
STEP 3:Installation Of CM 9 ICS Firmware
1.First up you need to download Zip file which is mentioned below in your computer
https://hotfile.com/dl/151919225/1624f9b/cm_beni-beta4.zip.html
2.Now, once you are done with downloading the above file in your computer, you need to now copy the file in your phone and ensure that you are not placing these file deep into the phone. Please note that you should not modify or rename the files which you have downloaded or else there is a high probability that the file would not be supported.
3.After this Enter in Recovery Mode by Holding Power Off + Menu Button Until Recovery Mode Appears.
4.In the recovery mode, you will have to choose “choose zip from SD”. Now, from the list of files and paths you will need to first select the file which is named as “cm_beni-beta4.zip (or which You Have Copied to SD Earlier)”. Ensure that you select the file properly.
5.Now, as soon as the process is over.Select Wipe Data/Factory Reset And Wipe Cache Partition.After All Done Select “Reboot System Now”
So, there you go as soon as the phone is rebooted you will see that the firmware is updated with the latest version of Android 4.0(ICS 4.0.3)...
No Need To Say THANKS Just Press It..
- Charge your device to a minimum of 90% as since the procedure is bit lengthy, the phone will consume more battery than the normal usage. Lesser battery will lead to the turning Off of the device in the middle of the firmware update process.
- Back up all your data which is there in the phone memory, as in an unlikely event if the data gets lost then you can easily restore the backup.
- Up next is you need to ensure that the USB Debugging is enabled in your phone. The USB Debugging can be enabled from the path of Settings > Applications > Development > USB debugging. Apart from this you also need to ensure that your computer has ADMIN privileges and USB Read / Write Access. It’s not recommended to use computers which have limited access.
Instructions For Custom ROM users
Just in case if you are on any of the custom ROMs then you need turn Off your phone so that you can then enter into the recovery mode. The recovery mode can be entered by pressing Volume UP Key + Middle button, and holding both simultaneously press the Power Button. If the device boots normally then you need to again try to enter the same.
In the recovery mode, select the options like Wipe data/factory reset, Wipe Cache partition and then select reboot system now to reboot the phone. You can select the options using the Volume keys and can select the appropriate option by pressing the Power button. This basically clears off all the cache data which is there in the phone so that the room can be made to accommodate this all new custom ROM firmwares
Procedure For Updating
STEP 1: Official Firmware Installation
First up you need to update your phone with the 2.3.x version of firmware (And not on Froyo 2.2.x). You need to follow the instructions which are mentioned below in the form of Links. Please note that it’s a base firmware and you need to install it
STEP 2:Install ClockWorkMod 5 Recovery Image
First up you need to download the beni_cwm-5_ext4_v2.tar & odin+beni.ops.zip.Extract the files and Find Odin 4.38.exe And BENI_v1.0.ops in your Extracted Folder.
Now, Switch off Your Fit And Enter into Download Mode By Pressing Power+Menu Button+Volume Down Button Until Downloading Mode Appears.Open S5670_Odin_Multi_Downloader_v4.38.exe.Place BENI_v1.0.ops on OPS tab.Check the One Package Option.Place beni_cwm-5_ext4_v2.tar on One Package tab.Connect the device to PC which you have put in Downloading Mode.Press Start and wait for flashing process is finished.
After this you will have to proceed to the next step which is mentioned Further
STEP 3:Installation Of CM 9 ICS Firmware
1.First up you need to download Zip file which is mentioned below in your computer
https://hotfile.com/dl/151919225/1624f9b/cm_beni-beta4.zip.html
2.Now, once you are done with downloading the above file in your computer, you need to now copy the file in your phone and ensure that you are not placing these file deep into the phone. Please note that you should not modify or rename the files which you have downloaded or else there is a high probability that the file would not be supported.
3.After this Enter in Recovery Mode by Holding Power Off + Menu Button Until Recovery Mode Appears.
4.In the recovery mode, you will have to choose “choose zip from SD”. Now, from the list of files and paths you will need to first select the file which is named as “cm_beni-beta4.zip (or which You Have Copied to SD Earlier)”. Ensure that you select the file properly.
5.Now, as soon as the process is over.Select Wipe Data/Factory Reset And Wipe Cache Partition.After All Done Select “Reboot System Now”
So, there you go as soon as the phone is rebooted you will see that the firmware is updated with the latest version of Android 4.0(ICS 4.0.3)...
No Need To Say THANKS Just Press It..
