FORUMS

HTC’s New Ad Campaign And What It Really Means

HTC has just released three new blind test adverts comparing app loading … more

XDA Picks: Best Apps of the Week (June 27 – July 4)

Apps are at the front and center of any smartphone experience, and with over a … more

HTC One M9 Developer Edition Android 5.1 OTA

The Developer Edition of the HTC One M9 is receiving an over-the-air update to Android 5.1. … more

Index Project For XDA Device Subforums

Another ambitious project from the collaborative efforts of Recognized Contributors and Forum … more

[Q] Bootloader then turns off. Can't get into recovery

51 posts
Thanks Meter: 9
 
By Nirmalspeed, Member on 28th March 2012, 10:52 PM
Post Reply Subscribe to Thread Email Thread
30th March 2012, 01:59 PM |#11  
OP Member
Thanks Meter: 9
 
More
Quote:
Originally Posted by Woodrube

OP, what ROM were you running when this happened intially? Also what kernel?

I have been reading most of the morning and am looking into some things. Alex's thread does show how to workaround the problem but it seems that the internal sd is lost (for now).

Since you are not the only one this happened to, I would like to know the above and see if it correlates to the others that this happened to in the Vibrant section. I'll post the same in their threads too.

i was running ICS Passion 13 with the Kiss kernel that came with it. and i've looked around and many people with ics have gotten this problem both on our device and on the AT&T's captivate.
 
 
31st March 2012, 03:44 AM |#12  
Junior Member
Thanks Meter: 2
 
More
If you loaded Eugene's rom, and are stuck at the recovery, don't wait so long to type that adb reboot command and don't unplug the usb just type the command. let the rom load then get the phone back in download mode and flash the stock rom.

Eugene's rom properly set up will fix your issue. try again!
31st March 2012, 04:17 PM |#13  
OP Member
Thanks Meter: 9
 
More
Quote:
Originally Posted by cotbu

If you loaded Eugene's rom, and are stuck at the recovery, don't wait so long to type that adb reboot command and don't unplug the usb just type the command. let the rom load then get the phone back in download mode and flash the stock rom.

Eugene's rom properly set up will fix your issue. try again!

that wouldn't work as the /data partition isn't being red by the phone. Nothing happens when i try that command.
2nd April 2012, 09:46 AM |#14  
Junior Member
Thanks Meter: 2
 
More
These are the instructions, Eugene's rom write like a lowlevel format, either you are not following directions or you actually bricked the vibrant.
But....you say you've made it to Eugene's recovery if you did you should be good to go.

Okay, Now with the Caution Posted, Lets Begin with the Froyo that Don't Brick

I have Tested this 5 Time's to Make Sure! Only install What I Post!

First,
You must already Have Odin installed & Know how to boot into Down-loader Mode!!

Do Not Select Repartition In ODIN Flasher


Quote:
Installing...
Extract the .zip file

Open ODIN Flasher, Select the Pit File.
Select Eugene373_GalaxyS_Froyo_PDA.tar
Select start..


Second,
Once Odin had Done Flashed, & you are in Recovery Mode you will not be able to Access anything & need to be at a Computer with Samsung Driver's installed & a working SDK pre-installed..

Side note: you will get an error in recovery, Don't be worried!!!! Ignore this!

Third,
Open a CMD Prompt & type:

Quote:
adb reboot


Froyo with Downgrading back to Stock Possible:
[COLOR="DarkRed"]Download here > EUGENE373_SamsungS_Froyo_PDA.zip
*Stock Froyo with*
~ Root
~ SuperUser.apk
~ Build.prop now Correct
~ Defualt.prop Also Correct
****
*Issue's
Volume Key are Reversed

****
*Not working*
~ Rom Manager via reboot to Recovery!
~ Selectable Menu in Recovery
~ 3.5 Head-jack
~ Hot Spot Tethering

sorry for stressing but, I have a 4yr old that loves playing with the vibrant and I think I've brought it back from every brick situation possible. As long as the vibrant has power, it will not stop! xd!
Post Reply Subscribe to Thread

Tags
bricked, encryption, recovery, unsuccessful
Previous Thread Next Thread
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes