Ok, Well now it prompted me to hit ctrl + c within 5 seconds, in which I did.
It just exits out of the program... :/
You don't do that. It's like press any key to exit lol
Sent from my ADR6425LVW using XDA
Ok, Well now it prompted me to hit ctrl + c within 5 seconds, in which I did.
It just exits out of the program... :/
Waiting device....
Found device... Please wait...
Getting into bar.....
Raising Glass
SUCCESS - Taking a sip.
SUCCESS - Beer is tasty.
SUCCESS - Beer is tasty.
SUCCESS - Beer is tasty.
SUCCESS - Beer is tasty.
SUCCESS - Buddies and Beer
Checking alcohol level......
Let's take one more......
S-OFF Failed
Errorcode: 66732337
ErrorMsg: Still sober
Quit....
Press ENTER to exit.....
Ive got the wire trick down but its been doing this every time... any ideas anyone?
Originally Posted by johnwaynegacy
whats the deal with my install?
loading sixpacks on sdcard...
loaded....
board vigor detected.
Just sits there forever,
there is a htc logo on my phone screen.
Im having the same problem!!!
Forgive me if this is a dumb question but....
I'm on the leaked firmware and I'm locked and unrooted. Let's say I pull a pc out of my ass ( because I have a mac ) and I use the all in 1 toolkit to get unlocked and load up a Rom. If I'm correct my hboot would then say "tampered " right? If I do s-off after this, and I flash the hboot they provide will the tampered go away and will it say s-off and locked instead of s-on and unlocked
Sent from my ADR6425LVW using Tapatalk 2
I have s-off but it wont boot it hangs at the juopunutbear screen...
looks like im f'cked procedure didnt complete, now when i start the phone. im stuck on the green arrow joupunutbear screen? am i bricked?
I also am having this same problem. I have been sitting at this screen for 30 minutes now. I'm assuming something hung. Has anyone found a fix for this specific problem (sorry if I missed it in my reading).
I am:
running Clean Rom
Windows 7
unlocked
started in Android
have USB debugging on
am unlocked
am rooted
Thanks!
In the proccess of restoring boot image now and going to give this another go. Placed the s-off files in my adb / fastboot folder now. Hopefully it plays nice. :/
In the proccess of restoring boot image now and going to give this another go. Placed the s-off files in my adb / fastboot folder now. Hopefully it plays nice. :/
Thanks. I'm giving it a try. Wish me luck haha.The second device I did this with had the same problem. I closed the program, pulled the battery on the phone, restarted it, and then I ran the program again and it would pick up right where it left off.
Thanks guys just kept trying and sure enough I got it. Timing is everything and I guess mines not always that great ask my last girlfriend LOL
Prerequisites said:Prerequisites
In order to use JuopunutBear you must meet the following pre-requisites:
Be unlocked using the HTCdev bootloader unlock
Be rooted (have superuser and/or an unsecured boot image installed)
Have a spare microSD card, or to have backed up all contents of your SDcard
Have fastboot and adb drivers installed and working (windows)
Have usb debugging enabled
Have a legth of insulated wire of sufficient length to join the contact points for your device. See images and videos for device specific information.
Instructions said:Instructions
(Optional) Perform a full backup and replace your sdcard with one that you are willing to wipe.
Ensure that your battery is fully charged.
Choose the correct download for your device and operating system
Extract the zip file to a new directory
Verify the MD5 checksum for your download
Read and/or watch the video for the device specific information for your device
Run controlbear as admin(windows) or root or using sudo on linux
Follow the on-screen instructions from ControlBear
Do not press any of the buttons on the phone during the process.
After doing the “wire-trick” yor phone will reboot. The sequence of the reboot may vary somewhat from that you see in the videos as these were taken during various stages of development.
If you see the following message from ControlBear after doing the wire trick:
ErrorMsg: Still sober.
This means that you have been unsuccessful in implementing the wire-trick. Run ControlBear again.
The usual casue for this is that you failed to perform 2 clean contacts or mistimed the wire trick.
Your phone will reboot several times during the process, this is normal. ControlBear will tell you when it has finished whether sucessfully or not.
Wire Trick said:Wire Trick
The “wire trick” is an essential part of the JuopunutBear S-OFF procedure.
When instructed to do so by the program you must perform the “wire trick” which is done as follows.
Obtain an insulated wire of appropriate length and gauge
Insert one end of the wire into the hole where pin 1 is indicated in the picture below, ensuring that a firm contact it made with the metal contact at the bottom of the hole
Briefly touch to other end of the wire to the contact marked GND in the picture below.
Wait approximately 1.75 seconds and then again touch the wire to the marked GND.
Allow the program to continue.
Note: it may take several attempts of running the program in order to obtain the correct timing for the wire trick.
The contact points for the “wire trick” are shown in the picture below.
Fix for external SD is as follows:
- Install busybox
- adb shell busybox fdisk /dev/block/mmcblk1
- type o
- type w
- adb shell busybox fdisk /dev/block/mmcblk1
- type n
- select primary, then 1
- chose default sizes
- type w
- adb shell busybox mkfs.vfat /dev/block/mmcblk1p1
For those of you having problems with internal storage, my apologies. We accidentally included the GB hboot.
Download this:
http://dl.dropbox.com/u/14779955/jb_hboot.zip MD5: b05336c08f709bf0a909205bcb95b951
Put the phone in fastboot mode, then run the follwoing commands:
Code:fastboot oem rebootRUU fastboot flash zip jb_hboot.zip fastboot reboot
Ignore the green bar.