Originally Posted by Darkman

CF-Auto Rooter and the App that us the Exynos Error are two different things...

Use the CF-Auto Rooter in first Post and then Triangle Away ... it works very fine on my GC with 4.1.2

I already did... I tried several ways for the past few hours...

My original ROM was stock 4.1.1 rooted.
I fwiped, flashed stock 4.1.2, CF Auto Root, Triangle Away, then factory reset.
When I went to download mode, the status displayed correctly as official, but the counter still not back to 0.

Re: How to root your Galaxy Camera

---

Here goes...

Stock 4.1.1 (I flashed back from 4.1.2)
CF Auto Root
Triangle Away 2.60

I'm trying to make my SGC back to factory default... so after binary counter back to 0, i'm planning to unroot and wipe.

that means triangle away setting (reset counter on every boot) is out of question.

as you can see, all the status back to official, I even can connect to OTA server (still have CF Auto Root).
but the counter can't back to 0.




Sent from my GT-I9300 using Tapatalk 2

I temporarily rooted my Camera and also couldn't get it to be completely un-rooted. I finally installed Kies on my Windows box (which takes forever as it is insanely bloated), but it had an option to force install factory firmware which I used to get it back to factory state (it was a little hard to find - I had to page through various menus to discover it). This was in the US with an AT&T version of the camera.

is this method compatible with XXBLL7 4.1.2?

im just making sure before i flash.. thanks

Originally Posted by AdamOutler

Warning
This cannot hurt your device because full recovery is simply a 1.1gig Odin flash away.

Introduction:
This is a Rooted Galaxy Camera CF AutoRoot based on GC100XXALK1.

You Will Need:

• A windows computer (or heimdall built from source and the files included in the package)
• The Recovery+Cache which will flash upon installation. Get it here: http://download.chainfire.eu/283/CF-...d1-ekgc100.zip
• The Odin version used is Version 1.85. Get it here: https://rapidshare.com/files/2195283307/Odin3_v1.85.zip
• Use JellyBean 4.1.1 build:GC100XXALK1 in case of problems. Get it here: http://www.hotfile.com/dl/179234447/...B_THL.zip.html

Instructions:

• unzip the CF-Auto-Root-gd1-ekgc100.tar.md5 from the zip package to a place you can find it.
• Launch the Odin3 application
  
  
  
• place CF-Auto-Root-gd1-ekgc100.tar.md5 in the "PDA" section
• Put your device into Download Mode:
  Remove and replace the battery.
  Press "Volume down+Camera+Power".
• Connect your device to your machine
• click start

Conclusion
By default, this device does not show a Warning Triangle. In the future it may. Go back to stock by using the 1.1G recovery package above after using TriangleAway by Chainfire.

Originally Posted by fren17

is this method compatible with XXBLL7 4.1.2?

im just making sure before i flash.. thanks

Yes it is!

i just used camera toolbbox to do it...no sweat

Runs perfect. Many thanks... Just started a Titanium Backup

once rooted.. what will happen if there a firmware upgrade? do we have to proceed or unroot it first?

Originally Posted by fren17

is this method compatible with XXBLL7 4.1.2?

im just making sure before i flash.. thanks

is this method compatible with XXBMA2 or XXBMA1 as well ?

Hi could someone put the bulb option in this camera? Long exposure surely will bring the galaxy camera to the fullest. thanks

Sent from my EK-GC100 using xda app-developers app