Disclaimer: I am not responsible for bricked devices, dead SD cards, thermonuclear war, or anything else. YOU doing this at your own risk.
This guide is taken from 4pda.ru forums and tested on my own device.
I strongly recommend you to make Nandroid backup with CWM Recovery v6.0.3.0 so after repartitioning ALL DATA (/system, /system1, /data, /cache) WILL BE ERASED.
1. Connect you phone to PC via USB. (USB debugging must be turned on)
2. Install MiFlash. Remember installation path. It will install drivers for "Android Composite ADB Device". If there's still one "Android" device without drivers - just ignore.
3. Run Command Prompt (cmd) and go to the %FOLDER_WHERE_YOU_INSTALLED_MIFLASH%\Google\Android (For me it was C:\Program Files (x86)\Xiaomi\MiPhone\Google\Android)
4. Type adb devices and press enter. It should start adb daemon and show your device with status offline. Check phone for dialog and allow USB debug from your computer.
5. Type adb devices again. Now it should show your phone with status device. Close Command Prompt.
6. Download and unpack to any folder attached archive tadb.zip
7. Run tadb shell.bat. If everything fine it will show something like "shell@android:/ $"
9. Type su and press enter. If requested allow root access on phone.
10. Now enter busybox fdisk /dev/block/mmcblk0 to start repartiotioning program (All changes are virtual until written)
11. Delete all partitions from 20 to 15 inclusive. For this enter d, enter 20, enter d, enter 19 till 15th partition.
After this enter p. Your partition table must be like this
12. Recreate needed partitions table. Press n, enter start block, end block. You can use attached partitions.xls to calculate needed values. Also You can change size of system partitions in this file as you wish (Make them 384Mb for example). Values will be recalculated.
13. Now we must return System type for 17th block (recovery). Enter t, enter 17, enter 60. After this operation your partiotion table will be like this (If you left 256Mb):
14. Time to save changes. If you not sure, you can just enter q to leave without saving changes. Enter w to write new partition table. Program will show error about using old partition table - that's normal. After you reboot phone - changes will be applied, so it will not load anything except fastboot.
15. Load phone in fastboot mode (Power + Volume Down + Mi-Button), go to folder with tadb and run flash_recovery.bat. It will flash CWM 6.0.3.0 to your device.
16. Go to mounts & storage menu and format /cache, /system, /system1 and /data
17. Now you can restore your nandroid backup.
NOTE: All operations been made on Windows 7 32-bit and Xiaomi Mi-One Plus with MIUIv5 3.7.19
This guide is taken from 4pda.ru forums and tested on my own device.
I strongly recommend you to make Nandroid backup with CWM Recovery v6.0.3.0 so after repartitioning ALL DATA (/system, /system1, /data, /cache) WILL BE ERASED.
1. Connect you phone to PC via USB. (USB debugging must be turned on)
2. Install MiFlash. Remember installation path. It will install drivers for "Android Composite ADB Device". If there's still one "Android" device without drivers - just ignore.
3. Run Command Prompt (cmd) and go to the %FOLDER_WHERE_YOU_INSTALLED_MIFLASH%\Google\Android (For me it was C:\Program Files (x86)\Xiaomi\MiPhone\Google\Android)
4. Type adb devices and press enter. It should start adb daemon and show your device with status offline. Check phone for dialog and allow USB debug from your computer.
5. Type adb devices again. Now it should show your phone with status device. Close Command Prompt.
6. Download and unpack to any folder attached archive tadb.zip
7. Run tadb shell.bat. If everything fine it will show something like "shell@android:/ $"
9. Type su and press enter. If requested allow root access on phone.
10. Now enter busybox fdisk /dev/block/mmcblk0 to start repartiotioning program (All changes are virtual until written)
11. Delete all partitions from 20 to 15 inclusive. For this enter d, enter 20, enter d, enter 19 till 15th partition.
After this enter p. Your partition table must be like this
Code:
Device Boot Start End Blocks Id System
/dev/block/mmcblk0p1 1 12801 102400 c Win95 FAT32 (LBA)
Partition 1 does not end on cylinder boundary
/dev/block/mmcblk0p2 * 12801 12863 500 4d Unknown
Partition 2 does not end on cylinder boundary
/dev/block/mmcblk0p3 12863 13051 1500 51 Unknown
Partition 3 does not end on cylinder boundary
/dev/block/mmcblk0p4 13051 488448 3803183+ 5 Extended
Partition 4 does not end on cylinder boundary
/dev/block/mmcblk0p5 13052 13114 500 47 Unknown
/dev/block/mmcblk0p6 13114 13370 2048 45 Unknown
/dev/block/mmcblk0p7 13370 13683 2500 4c Unknown
/dev/block/mmcblk0p8 13683 14963 10240 48 Unknown
/dev/block/mmcblk0p9 14963 16243 10240 64 Unknown
/dev/block/mmcblk0p10 16243 16305 500 46 Unknown
/dev/block/mmcblk0p11 16305 16368 500 65 Unknown
/dev/block/mmcblk0p12 16385 16768 3072 4a Unknown
/dev/block/mmcblk0p13 16769 17152 3072 4b Unknown
/dev/block/mmcblk0p14 20481 20864 3072 58 Unknown
13. Now we must return System type for 17th block (recovery). Enter t, enter 17, enter 60. After this operation your partiotion table will be like this (If you left 256Mb):
Code:
Device Boot Start End Blocks Id System
/dev/block/mmcblk0p1 1 12801 102400 c Win95 FAT32 (LBA)
Partition 1 does not end on cylinder boundary
/dev/block/mmcblk0p2 * 12801 12863 500 4d Unknown
Partition 2 does not end on cylinder boundary
/dev/block/mmcblk0p3 12863 13051 1500 51 Unknown
Partition 3 does not end on cylinder boundary
/dev/block/mmcblk0p4 13051 488448 3803183+ 5 Extended
Partition 4 does not end on cylinder boundary
/dev/block/mmcblk0p5 13052 13114 500 47 Unknown
/dev/block/mmcblk0p6 13114 13370 2048 45 Unknown
/dev/block/mmcblk0p7 13370 13683 2500 4c Unknown
/dev/block/mmcblk0p8 13683 14963 10240 48 Unknown
/dev/block/mmcblk0p9 14963 16243 10240 64 Unknown
/dev/block/mmcblk0p10 16243 16305 500 46 Unknown
/dev/block/mmcblk0p11 16305 16368 500 65 Unknown
/dev/block/mmcblk0p12 16385 16768 3072 4a Unknown
/dev/block/mmcblk0p13 16769 17152 3072 4b Unknown
/dev/block/mmcblk0p14 20481 20864 3072 58 Unknown
/dev/block/mmcblk0p15 20866 53633 262144 83 Linux
/dev/block/mmcblk0p16 53635 86402 262144 83 Linux
/dev/block/mmcblk0p17 86404 87683 10240 60 Unknown
/dev/block/mmcblk0p18 87685 88708 8192 83 Linux
/dev/block/mmcblk0p19 88710 111749 184320 83 Linux
/dev/block/mmcblk0p20 111751 488448 3013584 83 Linux
15. Load phone in fastboot mode (Power + Volume Down + Mi-Button), go to folder with tadb and run flash_recovery.bat. It will flash CWM 6.0.3.0 to your device.
16. Go to mounts & storage menu and format /cache, /system, /system1 and /data
17. Now you can restore your nandroid backup.
NOTE: All operations been made on Windows 7 32-bit and Xiaomi Mi-One Plus with MIUIv5 3.7.19
Attachments
Last edited: