Prompt [Q][Info][Tab3] System Dump / Kitchen

I'm trying to pull a system dump to make a Back it in kitchen for the Tab3 10.1

I did a ton of reading on this device, since there is not much developing with it
I pulled a Firmware/ system dump from My Samsung Galaxy Tab 3 10.1
GT-P5210 JDQ39.P5210UEUAMK1

It's rooted with recovery only

After pulling the dump I was able to load it up into kitchen
I loaded up the following three files:
boot.img, cache.img, and system.img
fired up the kitchen Set up working folder as usual
extracted it (no errors)
Added root permissions
Added Busybox
Added /etc/init.d script support
De-odex
zipalign all the APK's
updated the mounting point in the updater-script
Code:
unmount("/system");
format("ext4", "EMMC", "/dev/block/mmcblk0p8", "0");
mount("ext4", "EMMC", "/dev/block/mmcblk0p8", "/system");
-------------------------------------------------------------------------------------
I flashed it in recovery (seemed to have flashed) But when it reboots it just sits @ the boot screen.

Now I'm trying to figure out where i went wrong.
does below look correct?
are the commands i used correct?
Mounting points seem correct ?

I'm 99% sure the mounting points are correct..
I'm 50% sure I used the correct commands to create the sys dump etc
I'm not sure why the recovery img and boot img are the same exact size
(is it normal for the boot.img and the recovery.img to be the same exact size?)

I baked it in kitchen. with out any errors


here are the mounting points I used

1 '/efs' 'ext4' '/dev/block/mmcblk0p2'
2 '/config' 'ext4' '/dev/block/mmcblk0p3'
3 '/cache' 'ext4' '/dev/block/mmcblk0p6'
4 '/system' 'ext4' '/dev/block/mmcblk0p8'
5 '/data' 'ext4' '/dev/block/mmcblk0p9'
6 '/recovery' 'emmc' '/dev/block/mmcblk0p11'
7 '/modem' 'emmc' '/dev/block/mmcblk0p12'
8 '/preload' 'ext4' '/dev/block/mmcblk0p13'
9 '/boot' 'emmc' '/dev/block/mmcblk0p10'
10 '/sdcard' 'vfat' '/dev/block/mmcblk1p1'

I used these commands in terminal

Code:
dd if=/dev/block/mmcblk0p8 of=/mnt/extSdCard/backup/mmcblk0p8_system.img bs=4096
Code:
dd if=/dev/block/mmcblk0p10 of=/mnt/extSdCard/backup/mmcblk0p10_boot.img bs=4096
Code:
dd if=/dev/block/mmcblk0p6 of=/mnt/extSdCard/backup/mmcblk0p6_cache.img bs=4096
Code:
dd if=/dev/block/mmcblk0p12 of=/mnt/extSdCard/backup/mmcblk0p12_modem.img bs=4096
Code:
dd if=/dev/block/mmcblk0p11 of=/mnt/extSdCard/backup/mmcblk0p11_recovery.img bs=4096

So nowI ended up with


[*] mmcblk0p6_cache.img 350M [*] mcblk0p8_system.img 2.3G [*] mmcblk0p10_boot.img 20M [*] mmcblk0p11_recovery.img 20M [*] mmcblk0p12_modem.img 4.0M

etc

Any Help would be greatly appreciated