Attend XDA's Second Annual Developer Conference, XDA:DevCon 2014!
5,813,020 Members 54,022 Now Online
XDA Developers Android and Mobile Development Forum

Extended Battery Mod - P769 - with case

Tip us?
 
CAVO14
Old
#1  
Junior Member - OP
Thanks Meter 1
Posts: 2
Join Date: Aug 2013
Battery Low Extended Battery Mod - P769 - with case

This is an extended battery mod using two OEM batteries for the LG Optimus L9 P769. I am currently running AntonX's version of CM 10.2, which is OC'd to 1350 and UC'd to 200. Love his rom.

Credits to:
fastwanabe - http://forum.xda-developers.com/show....php?t=2397045

s0me guy - http://forum.xda-developers.com/show...ht=battery+mod

Do this mod at your own risk! Soldering together lithium-ion batteries can be dangerous especially if you short them out. Those without soldering skills probably shouldn't do this! This can also destroy your phone!

The case I used was a pandmimi ULAK case - http://www.amazon.com/gp/product/B00...?ie=UTF8&psc=1

I also suggest getting another wall charger with a higher amperage output. The stock charger might not work anymore. Something around 1.5 amps would probably do fine.

Suggested tools and parts:
- two new OEM BL-53qh batteries
- Soldering Equipment (Iron, Desoldering Braid, Solder, tip cleaner, etc)
- Wire to solder batteries together
- Small rotary cutting tool such as a dremel to cut case and back plate
- Razor knife to cut rubber sleeve
- Liquid Electrical Tape to cover exposed terminals
- Tape to hold batteries together
- Volt meter with a continuity or resistance function to test for shorts
- Double sided tape or tape roller up into a cylinder
- Pencil or marker

Step One- Gather materials and prepare a clean working area so you have ample room

Step Two- Charge both NEW batteries fully so their voltages are about the same.

Step Three - Place one battery in phone and put rolled up tape or double sided tape between back case and battery close it tight

Step Four - Remove back case so the battery comes out with it mark it with a pencil or marker

Step Five - Cut out back piece with razor knife or rotary cutting tool be careful not to break the back case. Keep the thin plastic we will use that later

Step Six - place the rubber piece on with nothing else and cut out the hole by pressing on it to mark the battery compartment and cut the rubber with the razor knife.

Step Seven - Tape both batteries together and place them in the phone put on the back case and the rubber. Place double sided tape on battery then line up the hard ULAK case with the rubber. Once alligned press them firmly together and pull the hard ULAK case off with the battery still attached. Mark where the batteries are with something. Remove the batteries and use the rotary cutting tool to cut the square battery hole out.

Step Eight - Clean up all the holes so that each piece can be removed without interfering with the batteries.

Step Nine- Use the liquid tape on the P769 back cover where the copper might be exposed

Step Ten - Solder positive to positive then check for shorts if there are no shorts solder negative to negative and check for shorts. if there are no shorts and the connections are good and sturdy then all the soldering is done. Make sure that the wire doesn't stick out to far from the battery because it might not fit in the battery compartment. To make things easier I burnt away the little bit of plastic that sticks up between the solder bridge and it is also a good idea to tin the connections and the wire before soldering them together.

Step Eleven - Once all the soldering is done and you are certain there are no shorts and your connections are good. connect the battery to the phone and try to turn it on. It should boot up with around 100% battery life during the first hour of use make sure to feel for battery warmth. If it starts to get really hot. It's probably messed up and you should fix it. Once all the checks are done and the battery fits in the phone fine use fast discharge and turn it on select everything if you want. Run it for about 5 or 10 minutes. if the battery gets warm but the temperature monitor doesn't move than your solder bridges are too tall making the other two connections not to touch the pins inside the battery compartment. After that is done and working use the liquid tape to cover the exposed connections that don't go inside your phone.

Step Twelve - Put the all the case pieces back on. Take the piece that you cut off the P769 back case and place it ontop of the battery use tape to tape it on. Then put on any decorative tape to cover the ugly hole. Take off the ULAK hard plastic case and put tape on the other side to prevent it slightly sticking to the battery. Then you can put it back together and enjoy you're long battery life.

Step Thirteen - Calibrate your phones battery http://forum.xda-developers.com/show....php?t=2192948

That's it. If anyone reads through it and doesn't understand or think I may have went too in depth they are welcomed to correct me. I hope you enjoy the mod whether you try or not that's up to you.
Attached Thumbnails
Click image for larger version

Name:	IMG_20140209_151431.jpg
Views:	263
Size:	233.6 KB
ID:	2569530   Click image for larger version

Name:	IMG_20140209_151534.jpg
Views:	243
Size:	231.5 KB
ID:	2569531   Click image for larger version

Name:	IMG_20140209_151542.jpg
Views:	216
Size:	231.8 KB
ID:	2569533   Click image for larger version

Name:	IMG_20140209_151552.jpg
Views:	217
Size:	239.0 KB
ID:	2569534   Click image for larger version

Name:	Screenshot_2014-02-09-15-34-03.png
Views:	236
Size:	68.1 KB
ID:	2569568  

Click image for larger version

Name:	Screenshot_2014-02-09-15-33-57.png
Views:	217
Size:	130.1 KB
ID:	2569569   Click image for larger version

Name:	Screenshot_2014-02-09-15-33-46.png
Views:	202
Size:	78.5 KB
ID:	2569570   Click image for larger version

Name:	Messenger_5827832163152033719_13894634638985884.jpg
Views:	195
Size:	92.7 KB
ID:	2569625   Click image for larger version

Name:	IMG_20140209_161103.jpg
Views:	169
Size:	238.4 KB
ID:	2569638   Click image for larger version

Name:	IMG_20140209_161201.jpg
Views:	179
Size:	242.7 KB
ID:	2569639  

Click image for larger version

Name:	IMG_20140209_161209.jpg
Views:	157
Size:	242.0 KB
ID:	2569640   Click image for larger version

Name:	IMG_20140209_161219.jpg
Views:	156
Size:	246.7 KB
ID:	2569641  
The Following User Says Thank You to CAVO14 For This Useful Post: [ Click to Expand ]
 
Ilxaot
Old
#2  
Ilxaot's Avatar
Senior Member
Thanks Meter 580
Posts: 1,115
Join Date: May 2013
Location: Parrish
That is absolutely sick. Father was showing me how to solder awhile back, maybe I'll get around to this
Take a moment to read this.
Romans 1:22 ~ Professing to be wise, they in turn became fools.
Humility is not thinking less of yourself, it is thinking of yourself less.
Veritas Aequitas

My Google+
A glad member of the Anti-Apple regime ^-^
 
CAVO14
Old
#3  
Junior Member - OP
Thanks Meter 1
Posts: 2
Join Date: Aug 2013
Yeah it's a pretty good mod. I love absolutely love it. feels good in my hand, it isn't heavy. it really isn't hard to do as long as you have the tools and take your time. I love it. idt i've had my phone die in one day since I have did the double battery mod. it's quite spectacular. I suppose I have the extra battery life because it's a bit undervolted by AntonX's CM 11.
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes